Black Box IC714A-449-R2 Manual de usuario
CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
MAY 1997
IC714A-449-R2 IC714AE-449-R2 IC714A-48-449-R2
IC714A-530-R2 IC714AE-530-R2 IC714A-48-530-R2
IC714A-V35-R2 IC714AE-V35-R2 IC714A-48-V35-R2
IC714A-X21-R2 IC714AE-X21-R2 IC714A-48-X21-R2
G.703 Codirectional Converter
G.703↔V.35 CODIRECTIONAL
PWR TD RD LOS TEST ERR PATT
REM
ANA
DIG
1
FCC AND DOC/MDC RFI STATEMENTS
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio-frequency energy, and if not
installed and used properly, that is, in strict accordance with the manufacturer’s
instructions, may cause interference to radio communication. It has been tested
and found to comply with the limits for a Class A computing device in accordance
with the specifications in Subpart B of Part 15 of FCC rules, which are designed to
provide reasonable protection against such interference when the equipment is
operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference, in which case the user at his own
expense will be required to take whatever measures may be necessary to correct
the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le
brouillage radioélectrique publié par Industrie Canada.
2
G.703 CODIRECTIONAL CONVERTER
NORMAS OFICIALES MEXICANAS (NOM)
ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de
que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que
sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá
a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser
referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,
alfombra o superficie similar puede bloquea la ventilación, no se debe colocar
en libreros o gabinetes que impidan el flujo de aire por los orificios de
ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del
tipo descrito en el instructivo de operación, o como se indique en el aparato.
3
NOM STATEMENT
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización
del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen del
aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas
de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea
usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean
derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su
desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
4
G.703 CODIRECTIONAL CONVERTER
DISCLAIMERS
This manual contains information proprietary to the manufacturer. No part
of this publication may be reproduced in any form whatsoever without prior
written approval.
No representation or warranties for the fitness of these products for any
purpose other than those specifically mentioned in this manual are made
either by the manufacturer or its agents.
The manufacturer reserves the right to revise this publication and make
changes without obligation to notify any person of such revisions and
changes.
The manufacturer shall not be liable for any direct, indirect, special,
incidental, or consequential damages, whether based on contract, tort, or any
legal theory.
SAFETY WARNING
Always observe standard safety precautions while installing, operating, or
troubleshooting this product. To avoid the possibility of electrical shock,
disconnect the unit’s power cord from the power source before you remove
the unit’s cover.
TRADEMARKS USED IN THIS MANUAL
Any trademarks mentioned in this manual are acknowledged to be the property of the
trademark owners.
5
TABLE OF CONTENTS
Contents
Chapter Page
1. Specifications .............................................................................................. 7
1.1 G.703 Interface ...................................................................................... 7
1.2 Data-Communications Interface .......................................................... 7
1.3 Data-Communications Control Signals ............................................... 8
1.4 Other Physical Specifications ............................................................... 9
2. Introduction .............................................................................................. 11
2.1 Functional Description ....................................................................... 11
2.2 Timing Theory .................................................................................... 13
2.2.1 CCITT G.703 Signalling ............................................................ 13
2.2.2 G.703 Codirectional Timing ..................................................... 13
2.2.3 Tail-End Clocking ...................................................................... 17
2.2.4 G.703 Codirectional Rules ......................................................... 17
2.3 Rate-Conversion Rules ........................................................................ 19
2.4 Physical Description ............................................................................ 19
3. Installation .................................................................................................. 20
3.1 Unpacking ........................................................................................... 20
3.2 Site Requirements ............................................................................... 20
3.3 Setting Jumpers ................................................................................... 21
3.3.1 Overview ..................................................................................... 21
3.3.2 The Jumper-Setting Procedure ................................................. 23
3.4 Installation in 19-Inch Racks .............................................................. 23
3.4.1 Overview ..................................................................................... 23
3.4.2 Installing a Single Unit in a 19-Inch Rack ................................ 24
3.4.3 Installing Two Units in a 19-Inch Rack ..................................... 25
3.5 Connecting Power and Data Cables .................................................. 27
3.5.1 Power Connection ..................................................................... 28
3.5.2 G.703 LINE Connection ............................................................ 29
3.5.3 DTE Connection ........................................................................ 30
3.5.4 Async Secondary-Channel Connection .................................... 30
6
G.703 CODIRECTIONAL CONVERTER
Contents (continued)
Chapter Page
4. Operation ................................................................................................... 31
4.1 Front-Panel Controls and LEDs ......................................................... 31
4.2 Operating Instructions ....................................................................... 33
4.2.1 Turn-On Procedure ................................................................... 33
4.2.2 Activating Loops ......................................................................... 33
4.2.3 Turn-Off Procedure ................................................................... 33
4.3 Diagnostic Loops ................................................................................. 33
4.3.1 The Modem Self-Test ................................................................. 34
4.3.2 Local Analog Loopback ............................................................. 35
4.3.3 Remote Digital Loopback .......................................................... 36
4.3.4 Local Digital Loopback ............................................................. 37
4.4 Calling Black Box ................................................................................ 38
4.5 Shipping and Packaging ..................................................................... 39
Appendix: Pinouts ............................................................................................. 42
7
CHAPTER 1: Specifications
1. Specifications
1.1 G.703 Interface
Type — Codirectional 64-kbps
Line — 4-wire, 19- to 26-gauge
Range — Up to 800 meters (1⁄2mile) over 24-gauge wire
Impedance — 120 ohms nominal
Balance — Greater than 45 dB (up to 256 kHz)
Greater than 35 dB (up to 384 kHz)
Return Loss — Less than 20 dB (up to 128 kHz)
Less than 14 dB (up to 384 kHz)
“Pulse” Amplitude — 1.0 V nominal
“Zero” Amplitude — 0 V ± 0.1 V max
Clock Frequency — 64 kHz
Frequency Tracking — ± 500 ppm
Connector — 5-screw terminal block
Jitter Performance — To G.823 requirements
1.2 Data Communications Interface
Type — Models with “-449” affix: EIA RS-530 adapted to
EIA RS-449 (ITU-TSS V.11/V.36/EIA RS-422/423);
Models with “-530” affix: EIA RS-530;
Models with “-V35” affix: ITU-TSS V.35;
Models with “-X21” affix: ITU-TSS X.21/V.11
8
G.703 CODIRECTIONAL CONVERTER
Data Rate — 64, 56, or 48 kbps, user-selectable
Spare Bandwidth — [at 56 or 48 kbps:] “1’s” density bit stuffing as per
ITU-TSS V.110; additional asynchronous channel
at 1200 bps; or transfer of RTS to DCD control
signal, end-to-end
Connector — Models with “-449” affix: DB25 female cabled to
DB37 female;
Models with “-530” affix: DB25 female;
Models with “-V35” affix: 34-pin M-block female;
Models with “-X21” affix: DB15 female
1.3 Data-Communications Control Signals
Functional — DCD, 64 kbps: ON when Rx pair contains required
violations, OFF when the Rx pair does not
contain required violations;
DCD, 48 or 56 kbps: When the Rx pair contains
the required violations, the DCD signal reflects
the state of the remote RTS; DCD is always OFF
when no violations are detected;
CTS output: ON after RTS ON, with delay; OFF
when RTS OFF, or during Loss of Signal
condition;
DSR output: ON (+V) when power is available
Clock Source — From G.703 Receive pair (LBT), from DCE (EXT),
or from internal source (INT), user-selectable;
If LBT, three sub-options are user-selectable:
Unit is DCE and RC and TC signals are outputs
from the unit to the local DTE (LBT-DTE);
RC signal is an output from the unit to the local
DTE, but TC signal is an input from a tail-
circuit DCE (LBT-DCE); or
X.21 only: Unit is DTE and RC and TC signals
are both inputs to the unit from the local DCE
(LBT-DCE21)
9
CHAPTER 1: Specifications
1.4 Other Physical Specifications
Compliance — EMI/RFI: FCC Part 15 Class A, DOC Class/MDC
classe A
Safety: IEC 380
Standards — Diagnostics: ITU-TSS V.52 and V.54
Internal Memory — 32 bits of RAM divided into (2) independent 16-bit
buffers
User Controls — (4) Front-mounted pushbuttons: Local Digital
Loopback (DIG), Local Analog Loopback (ANA),
Remote Digital Loopback (REM), and Test
Pattern (PATT);
(5) Internal jumpers: Connect/disconnect grounds,
clock source, LBT clock-signal derivation, data
rate, and V.54 delay;
(1) Internal solder contact to connect grounds;
Loopback tests can also be triggered by interface
signals from local DTE
Diagnostics — Local digital loopback; local analog loopback (V.54
Loop 3); remote digital loopback (V.54 Loop 2);
511-bit V.52 BERT; all user-initiated and user-
terminated
Indicators — (6) Front-mounted LEDs: Power (PWR), Receive
Data (RD), Transmit Data (TD), Loss of Signal
(LOS), Test (TEST), and Error (ERR)
Power — IC714A models : Directly from outlet through
detachable 6-ft. (1.8-m) power cord (included):
Optimal
Input: 115 VAC, 60 Hz, 0.2 amps;
Input Ranges: 103.5 to 126.5 VAC, 47 to 63 Hz;
IC714AE models: Directly
from outlet through
detachable 6-ft. (1.8-m) power cord (included):
Optimal
Input: 230 VAC, 50 Hz, 0.1 amps;
Input Ranges: 207 to 253 VAC, 47 to 63 Hz;
Este manual sirve para los siguientes modelos
11
Tabla de contenidos
Otros manuales de Convertidor de medios de Black Box
Black Box
Black Box LPD401A Manual de usuario
Black Box
Black Box LE2120A-R4 Manual de usuario
Black Box
Black Box IC920A Manual de usuario
Black Box
Black Box LMC009A-R4 Manual de usuario
Black Box
Black Box AC215A Manual de usuario
Black Box
Black Box LE1500-BNC Manual de usuario
Black Box
Black Box AC136A Manual de usuario
Black Box
Black Box LMC11032A Manual de usuario
Black Box
Black Box IC135A Manual de usuario
Black Box
Black Box AC340A Manual de usuario
Black Box
Black Box AVSC-VGA-HDMI Manual de usuario
Black Box
Black Box AC500A-R2 Manual de usuario
Black Box
Black Box LH1703A-SC-US Manual de usuario
Black Box
Black Box AC139A Manual de usuario
Black Box
Black Box LMC1600A Manual de usuario
Black Box
Black Box AVSC-HDMI Manual de usuario
Black Box
Black Box AC328A-R4 Manual de usuario
Black Box
Black Box MT660A-MM Manual de usuario
Black Box
Black Box AC135A-R2 Manual de usuario
Black Box
Black Box VSP-HDMI1X8-4K Manual de usuario
