Black Box FAS 200 / MFA Manual de usuario
FAS 200 / MFA
Users Manual
--● Safety Instruction 3
---●Getting Started 4
----●Parts Descriptions 5
-----●Product Components 6
------●Installation 7
-----●Functions 12
----●Program 20
---●Specifications 24
Contents
Because the safety instruction is for preventing the accident or danger by using the product safely and correctly, please
keep the instructions invariably. We cannot be held responsible for what happens to our products when you did not keep
this users manual.
Safety Instruction
Warning Death, serious injury damage may result when following instructions are not observed
To dry this unit, do not use heat machines
(stove, microwave).
Fail to do may result in explosion or mal-function.
Do not disassemble or shock
No goods damaged by doing so will be accepted for free
service or replacement.
To clean the unit, do not use chemicals
(benzene, alcohol, thinner)
Fail to do may result in fire.
Do not look into IR sensor while using the remote
controller.
Fail to do may result in eye problems.
Caution injury or property damage may result when following instructions are not observed
Install the product according to the
manual
Fail to do may result in mal-function.
Keep the windshield clean especially front area of
lens
The system may not operate properly when objects or
debris block the camera lens of there is a reflection.
Tape the unit stably using both face tape.
Fail to do may result in decreasing performance of
system due to movement of unit by vibration of vehicle.
Do not place any objects on dash board
The system will not operate normally/regularly when
other items on dashboard reflects off the glass and
interferes with device. Minimize display viewing while driving
Viewing the display may distract the driver from looking
ahead of the vehicle and cause an accident.
This product is an intelligent ASV(Advanced Safety Vehicle) system that is verified by Korean
motor manufactures. Using high-technologies and equipment experience to top quality vehicle,
there are the lane departure warning, the front car departure warning and the black box function
that the frontal images and acceleration values are stored when a sudden stop or traffic accident is
occurred.
This product is intended to be a driving support system for safer driving. Inca Systems is not
responsible or liable in event of an accident or citation. Please follow all applicable road, vehicle
and traffic regulations carefully.
This hardware, software and intellectual property belong to the manufacturer. Copying,
processing, or distributing the product without written permission will be punished to
the fullest extent of the intellectual property rights laws, and of course, will be claimed
for damages.
The specification in manual may be modified for quality improvement without any notice.
Getting started
Parts Description
Power Input (DC 5V) and PC download
1
2
3
5
6
410
8
7
9
12
13 1
Camera sensor
2
Horizontal bar
3
Reset switch
4
LED
5
Power/Recording switch
Press a while(5 seconds), power ON/OFF
Press shortly (1 second), images are stored
with click sound
6
RC receiver
7
USB output
8
GPS input(option)
9
Speaker
10
Tilt controller
12
Mount
13
11
Rotator(360 degrees)
11
Product is composed of 8 components as shown in below figures. Please check all
components prior to installation.
Components
Main Unit Cigar adapter USB download cable Remote control
Software CD Cradle Both face tape Product decription
* Above components may be modified without any notice according to the component supplies.
Installation
This product should be installed while the vehicle is parked on a level road or parking lot with engine
off.
All the components required for installation are contained in the product box. Please review the
installation procedure prior to installation.
This installation procedure is for installation in passenger cars and SUVs. If installing the device in a
bus or truck, whole processing is similar to passenger car except the installation location of unit. This
location is explained separately, please refer to the page 10.
Please confirm that the camera installation is not blocking nor interfering with driver’s view of the
windshield.
If possible, hiding the cables enables to improve the safety and the fine view.
Keep the windshield clean especially front area of lens.
Set the correct time using the S/W served with package for recording the correct traffic accident time.
The setting can is accomplished while first purchase or first video data PC download.
Caution
Installation
Installation (Passenger Car, SUV, Larger SUV)
1
2
Confirm where to install the unit first. Prior to installation, clean the windshield
where the unit is to be installed. It is recommended that the unit is installed on
the windshield behind the rearview mirror in the area with anti-sun protection.
Please confirm that the unit installation is not blocking not interfering with the
driver’s view of the windshield.
Adjust the unit to the horizontal level in the middle. Peel off one side of the
tape and attach it to the desired area of windshield. Please confirm the tape
is attached tightly.
3After connect the cigarette cable to the cigarette socket of vehicle, connect the
mini USB connector on the opposite side to connector of unit that is marked as
DC 5V/USB (①). And turn on the engine, confirm that you can hear guidance
voice.
Installation
4
5To adjust the angle of unit, loosen the screw of the tilt controller (12) and adjust
a tilt angle to the unit until hearing beep. The beep is occurred when the camera
is entering the proper angle range. If You decrease the angle again, You here
the same beep again. You should now carefully and slowly adjust the angle
within this range so, that You hear one long beep for 3 seconds continuously.
Fasten the screw in this setting. Wait for the announcement Camera setting is
completed. (or press the automobile type selection button once more) If you
should hear Camera setting error! you should repeat the adjustment
procedure beginning with Step 4 once more. It is important to proceed slowly
and carefully- only the long beep is the correct signal which is accepted by the
system.
Installation (Passenger Car, SUV, Larger SUV)
Press the car button , followed by the “Save” button of the remote
controller for selecting the vehicle type. You will hear “Systems will select
automobile types”. The 5 kinds of vehicle types are supported, passenger car,
SUV, larger SUV, bus/truck type 1 and bus/truck type 2. Please select a proper
vehicle type using volume buttons. Then the system gives a ring 2 times.
Now the the system will be ready for the camera angle adjustment.
Installation
Press the power cable and video cable into the grove between the
windshield and the upholstery of the vehicle. You may use the mounts to
arrange the cable if needed.
6
This product have an ability that can rotate 360 degrees. Thus, if you want to
use for indoor image black box, rotate unit to the opposite side of front. When
rotate the unit, please check cable connectivity carefully.
Installation (Passenger Car, SUV, Larger SUV)
After proper vehicle type is selected and the camera is adjusted, you should drive the car on a road now and find a
road section with proper lane markings as soon as possible. The system will not start correct operation, before
You have passed at least 1 x such a road section for at least 30 seconds with a speed slightly higher than the
adjusted minimum speed warning level. Later, the image recognition software inside the camera will automatically
repeat the adjustments regularly and is even able to adjust the system temporarily to different lane marking
systems used in construction areas. After the system has made all internal adjustments and calibrations,
You will hear an announcement, that the warning system is now working properly.
Important note: Never press the automobile type selection button during driving- because pressing this knob
automatically will erase the old camera calibration and starts a new calibration procedure. If this should happen
accidentally, You can restore the old setting by waiting the 2 beeps, which start the tilt adjustment time and press
1 x the same knob again. This will restore the previous calibration again and the system will work again after
short time.
7
Tabla de contenidos
Otros manuales de Cámara de salpicadero de Black Box
