BirCraft BADCD12-10 Manual de usuario

Address: 320 B Percheron Road, Kyalami, Midrand, 1684

GPS Coordinates: S 25.98115º / E 028.06869º

BirCraft

GEARED MOTORS - LINEAR ACTUATORS - CONTROLS

+ (27) 011 468 1881

+(27) 074 465 1744

01@BirCraft.co.za

www.BirCraft.co.za

GUIDELINE DIMENSIONS ONLY

- Over

40 Years

of Supplying Africa -

Variable DC Speed Drives –Operation Manual

BADCD12-10 and BADCD24-10

Contents

Safety Precautions: .............................................................................................................................................................................................................................. 1

Specification and Model: ..................................................................................................................................................................................................................... 1

Product Characteristics:....................................................................................................................................................................................................................... 2

Installation Requirements:................................................................................................................................................................................................................... 2

Performance Indexes:.......................................................................................................................................................................................................................... 2

Wiring Requirements:.......................................................................................................................................................................................................................... 3

Driver Terminal Function Diagram:...................................................................................................................................................................................................... 3

Description of control Terminal’s Functions: ....................................................................................................................................................................................... 3

EN (Enable Control).................................................................................................................................................................................................................... 3

DIR (Direction Control)............................................................................................................................................................................................................... 3

C E (OC Door Alarm Output)....................................................................................................................................................................................................... 4

4. S1 S2 S3 Signal Output Terminal: ..................................................................................................................................................................................................... 4

Description of Indicator: ...................................................................................................................................................................................................................... 5

Regulation Description of Functional Potentiometer:.......................................................................................................................................................................... 5

Driver Examination steps before Charged: .......................................................................................................................................................................................... 5

Common Fault Treatment:................................................................................................................................................................................................................... 5

Safety Precautions:

•Installation, connection and commissioning of this device shall be carried out by professionals.

•Do not install, remove or replace device circuit under charged circumstances.

•Please make sure that necessary protectors are mounted between power input end of this device and power supply

(storage battery) to avoid accidents or fatal damages; Devices need to be mounted: over-current protector, fuse,

emergency switch.

•Isolation and insulation protection between device and ground as well as devices shall be well equipped.

•In case that charged commissioning of this device is really needed, well-insulated non-metal special screwdriver or

special commissioning tools shall be used.

•This device shall be installed in well-ventilated environment.

•This device shall not be directly exposed to abnormal environments with high humidity, dust, corrosive gas and intense

vibration.

Specification and Model:

PRODUCT #:

CONTINUOUS OUTPUT CURRENT

DC (A):

MAX OUTPUT CURRENT

DC (A):

DC VOLTAGE WORKING RANGE

10-18 DC (V):

BADCD12-10

10 - 18

BADCD24-10

20 - 55

T: 011 468 1881 |www.BirCraft.co.za

C: 074 465 1744 |e: 01@BirCraft.co.za

Address: 320 B Percheron Road, Kyalami, Midrand, 1684

GPS Coordinates: S 25.98115º / E 028.06869º

Page 2of 5

Variable Speed Drives –Operation Manual

BADCD12-10 and BADCD24-10

- Over

40 Years

of Supplying Africa -

GUIDELINE DIMENSIONS ONLY

Product Characteristics:

This series of speed controller is a low voltage DC four-quadrant regeneration pulse width controller adopts special single-chip

intelligent control system and has rapid response speed, steady operation, reliable work status and multiple protection functions.

•SMT technology, small size.

•Pulse width modulation.

•Low noise during operation, high efficiency, and low maintenance cost which better enhance the service life of DC

motor.

•Four-quadrant regenerative operating mode.

•Regenerative braking function.

•It doesn’t need external reversing contactor and will not result in electric motor parts or other components overheating

or burning down.

•Enable/ reversing terminal.

•To realize certain functions by using simple passive switching value or transistor collector open circuit.

•Status indicator light - Power supply indicator and over-current alarm indicator can provide the visible status of speed

controller.

•Output current setting function (amplitude limiting).

•Torque compensate function.

•Double closed-loop PI regulation (current, voltage).

•Standard analogue quantity signal control analogue quantity: 0-6V 0-10V or controlled by potentiometer

•A broader scope of input voltage: 10-55V.

Installation Requirements:

•Controller cannot be installed, connected or removed under charged circumstance. Otherwise accidents or severe

damages may be caused. Users should read and understand the details of “safety warning” (Page 1) before installation

and obey the rules strictly.

•Drive element is sensitive to electrostatic magnetic interference shall be kept away from environments where static is

easy to be generated; otherwise, speed controller may be damaged.

•The driver shall be kept away from dust, high humidity environment and prevented from accidental contact. Enough

space shall be reserved around the driver for easy ventilation and regulation.

•When fixed, the driver shall be kept from other heat sources. Guarantee that the driver works in the specified

environment temperature range.

•The driver shall not be installed on equipment’s with extreme vibration; if not, precaution against vibration shall be

taken.

Performance Indexes:

SPEED RATIO:

1:100

CONTROL POTENTIOMETER

(1K ……50K) / 2W

INPUT VOLTAGE:

10-55V VDC

OUTPUT CURRENT:

0-20A (Amplitude Limiting)

INPUT IMPEDANCE:

≥50KΩ

ROTATE SPEED (STANDARD PRECISION %):

1 %

START/BRAKING TIME:

0.2-20 S

ENVIRONMENT TEMPERATURE:

-10°C + 50°C

ENVIRONMENT HUMIDITY:

≤80RH (no moisture condensation) (relative humidity)

INSULATION AND VOLTAGE RESISTANCE:

1100V DC 1 minute

INSULATION RESISTANCE:

> 20 MΩ

LEAKAGE CURRENT:

≤ 0.9 mA

WEIGHT:

0.25 KG

•It is appropriate for permanent magnet and separately excited motor

T: 011 468 1881 |www.BirCraft.co.za

C: 074 465 1744 |e: 01@BirCraft.co.za

Address: 320 B Percheron Road, Kyalami, Midrand, 1684

GPS Coordinates: S 25.98115º / E 028.06869º

Page 3of 5

Variable Speed Drives –Operation Manual

BADCD12-10 and BADCD24-10

- Over

40 Years

of Supplying Africa -

GUIDELINE DIMENSIONS ONLY

Wiring Requirements:

•Do not connect wire under charged.

•Insulated connection, shielded wire which match with driver’s voltage current shall be selected and connected,

specifications of driver’s power input wire and motor’s wire are shown below:

Table 1 Wire Specification and Length Table

CURRENT (A)

WIRE SPECIFICATION (MM2)

MAX. LENGTH (M)

1.5

2.5

•Signal line and control line shall adopt shielded wire and shall be separated with power input wire and output wire.

•The driver does not have internal power supply reverse connection protection function, make sure that wiring between

power input and driver is correct, otherwise the driver may be damaged.

•Proper tools shall be used for wiring and make sure that wiring is correct.

Driver Terminal Function Diagram:

Description of control Terminal’s Functions:

EN (Enable Control)

During motor operation, simply connect/ disconnect EN with COM to control the start and stop of motor

Connect EN terminal with COM, EN terminal is effective, at this time regulate external speed potentiometer and

motor is in normal operation.

EN terminal suspends in the air or is not connected, EN terminal is invalid; circuit of controller is blocked and motor

stops.

DIR (Direction Control)

During motor operation, simply connect/ disconnect EN with COM to reverse the motor rotation. It doesn’t need

external reversing contactor and will not result in electric motor parts or other components overheating or burning

down.

Connect DIR terminal with COM, DIR terminal is effective, motor is in negative rotation.

DIR terminal suspends in the air or is not connected, DIR terminal is invalid; motor is in positive rotation (runs in

opposite direction as above mentioned).

In any cases, signal line and logic control line shall not be bound, mixed and wired with power input wire, output wire

(motor line) and other power lines. Induced voltage generated may cause interface, malfunction or directly damage the

driver.

T: 011 468 1881 |www.BirCraft.co.za

C: 074 465 1744 |e: 01@BirCraft.co.za

Address: 320 B Percheron Road, Kyalami, Midrand, 1684

GPS Coordinates: S 25.98115º / E 028.06869º

Page 4of 5

Variable Speed Drives –Operation Manual

BADCD12-10 and BADCD24-10

- Over

40 Years

of Supplying Africa -

GUIDELINE DIMENSIONS ONLY

C E (OC Door Alarm Output)

The internal design of “OC door alarm output”is that over‐current signal is transmitted through an opto‐coupler to

give alarms. When over‐current is detected on the controller, over‐current signal will be immediately sent to diode

of opto‐coupler for break over and then transmitted to C, E ports. The client can wire as their own requirements, as

shown in Figure 1, connect to over‐current indicator, Figure 2, relay actuation after over‐current to give alarms.

Internal wiring diagram of “OC door alarm output”is shown as follows:

4. S1 S2 S3 Signal Output Terminal:

Such controller has two control modes of external speed potentiometer control and external analogue quantity input.

Description of various terminals is as follows:

•S1 Terminal: external power+10V ，

•S2 Terminal: signal input terminal

•S3 Terminal: GND (grounded).

When external speed potentiometer control is used, S1, S2, S3 terminals shall be connected with external potentiometer as

shown in VI. Driver terminal function diagram to regulate external potentiometer for speed governing

When external analogue quantity input control is used, speed can be controlled through S2 and S3 input, both 0‐ 5V and 0‐10V

are OK.

T: 011 468 1881 |www.BirCraft.co.za

C: 074 465 1744 |e: 01@BirCraft.co.za

Address: 320 B Percheron Road, Kyalami, Midrand, 1684

GPS Coordinates: S 25.98115º / E 028.06869º

Page 5of 5

Variable Speed Drives –Operation Manual

BADCD12-10 and BADCD24-10

- Over

40 Years

of Supplying Africa -

GUIDELINE DIMENSIONS ONLY

Description of Indicator:

POWER (Green) power indicator:

If the controller is charged, this indicator lights up to indicate that controller is under normal operation.

TORQUE (Red) over-current indicator:

Turns red to indicate that output current of the controller exceeds client’s pre-set current, and the controller will automatically

limit the output current to such value.

Regulation Description of Functional Potentiometer:

MAX (Maximum Revolving Speed Limit)

It is used for limiting motor’s maximum revolving speed. Increase in clockwise rotation and decrease in counter clockwise rotation.

IR (Torque Compensation)

Regulate “IR” enable motor work under different loads and keep revolving speed constant (normally factory default is 0), Increase

in clockwise rotation and decrease in counter clockwise rotation.

RAMP (Soft Start/ Stop)

Regulate “RAMP” to set motor’s starting and stopping time (1-20 S). Increase in clockwise rotation.

TORQUE (Current Limit Regulation)

Regulate “TORQUE” to set over-current protection value of the controller; regulating range is 0-20A, Increase in clockwise rotation

and decrease in counter clockwise rotation. When reaches over-current limit value, over-current indicator (Red) lights constantly

and current is be limited to such value, at this time, continue to regulate the external potentiometer, current value is invariant(

i.e. amplitude limiting).

Driver Examination steps before Charged:

•Firstly, check whether positive and negative connection of battery pack and driver is correct, reliable and whether input

power is within driver’s applicable range.

•Check whether the circuit board of driver is clean, clear and without conductive metals, humidity, dew and debris

•Check whether periphery connecting line of driver is correct and free from short circuit and ground connection.

•Confirm that external speed governing potentiometer is at minimum position (given signal is at 0)

Common Fault Treatment:

PROBLEMS

CAUSES

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

Danfoss

Danfoss VLT 2800 Series Hoja de especificaciones

ABB

ABB ACQ580-01 Series Manual de instalación

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

ABB

ABB RSYC-01 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario