Biostar M7SXG Manual de usuario

M7SXG

Federal Communications Commission

(F.C.C) Statement

This device complies with Part 15 of the FCC Rules. Operation of this device is

subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Accessories: This device has been tested and found to comply with the limits of a

Class B digital device; the accessories associated with this equipment are as

follows:

1. Shielded serial cable. (Can be obtained from multiple retail outlets)

2. Shielded printer cable. (Can be obtained from multiple retail outlets)

3. Shielded video cable. (Can be obtained from multiple retail outlets)

4. Shielded power cord. (Provided by manufacturer)

These accessories are required to ensure compliance with FCC Rules. It is the

responsibility of the user to provide and use these accessories properly.

This equipment has been tested and found to comply with the limits of a Class B

digital device, pursuant of Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and radiates radio frequency energy

and, if you did not installed and used in accordance with the instructions, may cause

harmful interference in the radio communications. There is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference in the radio or television reception, which can be determined

by turning the equipment off and on, you are encouraged to try to correct the

interference by one or more of the following measures:

1. Reorient / relocate the receiving antenna.

2. Increase the separation between the equipment and the receiver.

3. Connect the equipment into an outlet from a different circuit where the

receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications that is not expressly approved by the

manufacturer could void the user’s authority to operate the equipment.

Disclaimer

The vendor makes no representations or warranties with respect to the contents

and specially the vendor disclaims any implied warranties of merchantability or

fitness for any purpose. Further the vendor reserves the right to revise this

publication and to make changes of the contents without obligation to notify any

party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

Trademarks and Remarks

MS-DOS, Windows, Windows NT, Windows 9X, Windows ME, Windows XP

and Windows 2000 are products of Microsoft Corp, with its ownership of

trademark, and are distributed by the vendor under a license agreement.

All trademarks used in this manual are property of their respective owners.

Canadian D.O.C. Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions

from digital apparatus to set out of the radio interference regulations of the

Canadian Department of Communications.

Cet appareil numbérique n‘émet pas de bruits radioélectriques dépassant les

limites appliquées aux appareils numériques de Class B préscrits dans le réglement

du brouillage radioélectrique edict par leminister Des Communications du Canada.

Contents

Introduction ..................................................................................1-1

1. Motherboard Description ........................................................1-2

1.1 Features...................................................................................................1-2

1.1.1 Hardware...........................................................................................................1-2

1.1.2 BIOS.................................................................................................................1-6

1.1.3 Software............................................................................................................1-6

1.1.4 Accessories.......................................................................................................1-6

1.2 Motherboard Installation.........................................................................1-7

1.2.1 System Block Diagram....................................................................................1-7

1.2.2 Layout of Motherboard....................................................................................1-8

1.2.3 Quick Reference............................................................................................... 1-8

1.2.3 Quick Reference............................................................................................... 1-9

1.3 CPU Installation....................................................................................1-10

1.3.1 CPU Installation Procedure: Socket 478......................................................1-10

1.3.2 CPU Fan Header: JCFAN1...........................................................................1-11

1.3.3 System Fan Header: JSFAN1 (Optional).....................................................1-11

1.4 RAM Module Installation.....................................................................1-12

1.4.1 DIMM.............................................................................................................1-12

1.4.2 How toinstall a DIMM Module...................................................................1-13

1.5 Slots ......................................................................................................1-14

1.5.1 AGP (Accelerated Graphics Port) Slot.........................................................1-15

1.5.2 CNR (Communication Network Riser) Slot................................................1-15

1.5.3 PCI (Peripheral Component Interconnect) Slots..........................................1-15

Contents

1.6 Connectors, Headers & Jumpers...........................................................1-16

1.6.1 Front Panel Connector: JPANEL1 ...............................................................1-17

1.6.2 ATX 20-pin Power Connector: JATXPWR1..............................................1-19

1.6.3 ATX 12V Power Connector: JATXPWR2.................................................1-19

1.6.4 DIMM Power Voltage Selection: JDIMMPWR1 ......................................1-19

1.6.5 AUX Power Connector: JAUXPWR1 (Optional)......................................1-20

1.6.6 Hard Disk Connectors: IDE1/IDE2..............................................................1-20

1.6.7 FloppyDisk Connector: FDD1.....................................................................1-20

1.6.8 Wake On LAN Header: JWOL1..................................................................1-21

1.6.9 Clear CMOSJumper: JCMOS1...................................................................1-21

1.6.10 Front USB Headers: JUSB1/JUSB2..........................................................1-22

1.7 Peripheral Port.......................................................................................1-23

1.7.1 PS/2 Mouse / Keyboard Connector: JKBMS1............................................1-23

1.7.2 USB & LAN Connectors: JUSBLAN1.......................................................1-24

1.7.3 VGA Connector: JVGA1..............................................................................1-25

1.7.4 Serial and Parallel Interface Ports..................................................................1-26

1.7.4.1 The Serial Interface: JCOM1...................................................................1-26

1.7.4.2 Parallel Interface Port: JPRNT1 ..............................................................1-28

1.7.5 Game (Joystick/MIDI) Port Connector: JGAME1 .....................................1-29

1.7.6 Audio Port Connectors: JSPKR1/JLIN1/JMIC1.........................................1-29

1.7.7 Audio Subsystem...........................................................................................1-30

1.7.7.1 CD-ROM Audio-In Header: JCDIN1 .....................................................1-31

1.7.7.2 CD-ROM Audio-In Header: JCDIN2 .....................................................1-31

1.7.7.3 Front Panel Audio Header: JAUDIO1 ....................................................1-31

Contents

iii

1.7.7.4 Telephony Audio Header: JTAD1...........................................................1-31

2. BIOS Setup................................................................................2-1

2.1 Main Menu..............................................................................................2-3

2.2 Standard CMOS Features........................................................................2-6

2.3 Advanced BIOS Features........................................................................2-9

2.4 Advanced Chipset Features...................................................................2-13

2.5 Integrated Peripherals ...........................................................................2-15

2.6 Power Management Setup.....................................................................2-21

2.7 PnP/PCI Configurations........................................................................2-24

2.8 PC Health Status ...................................................................................2-27

2.9 Frequency Control.................................................................................2-29

3. Trouble Shooting.......................................................................3-1

Chapter 1 Motherboard Description

1-1

Introduction

System Overview

Congratulations on the purchase of your new system! This motherboard is designed to

take advantage of the latest industry technology to provide you with the ultimate

solution in data processing. In the tradition of its predecessors, this motherboard

continues the commitment of reliability, performance and strives for full compliance

and compatibility with industry software and hardware standards.

M7SXG Highlights:

8 Contains on board I/O facilities, which include one serial port, a parallel port, a PS/2

mouse port, a PS/2 keyboard port, audio ports, USB ports, a game port and a VGA

port.

8 Contains on board IDE facilities for IDE devices such as hard disks and CD-ROM

Drives.

8 Supports the Intel Pentium®4 (Socket 478) processor, a leading edge processor which

brings to you the latest technology in micro architecture design, graphics performance,

system bus design, cache architecture and much more.

8 Complies with PC Micro ATX form factor specifications.

8 Supports popular operating systems such as Windows 95/98, Windows NT, Windows

2000, Windows ME, Windows XP, Novell and SCO UNIX.

Chapter 1 Motherboard Description

1-2

1. Motherboard Description

1.1 Features

1.1.1 Hardware

CPU

−Provides Socket-478.

−Supports the Intel Pentium®4 processor providing the new generation

power for high-end workstations system.

Speed

−Runing at 400 MHz Front Side Bus frequency.

−Supports up to 2.2 GHz CPU core speeds.

−The 33MHz 32 bit PCI 2.2 compliant.

−The 66MHz AGP 2.0 compliant interface supports 1x, 2x and 4x data

transfer mode.

Chipset

−SiS 650/645, SiS 961.

−Winbond W83697HF.

DRAM Memory

−Supports 200MHz, 266MHz or 333MHz(only for SiS 645) DDR

SDRAM devices.

−Supports 128Mb, 256Mb ,512Mb and 1GB technologies.

−Max of 2 Double-Sided DIMMs with unbuffer (without ECC)

PC2100/PC1600/PC2700(only for SiS 645).

−The largest memory capacity is 2 GB for unbuffer DIMMs.

Shadow RAM

−Motherboard is equipped with a memory controller providing shadow

RAM and support for ROM BIOS.

Chapter 1 Motherboard Description

1-3

Green Functionality

−Supports Award BIOS ™ power management functionality.

−Has a power down timer from 1 to 15 minutes.

−Wakes from power saving sleep mode with any keyboard or mouse

activity.

BUS Slots

−One AGP slot (support AGP v2.0 compliant).

−One CNR slot.

−Three 32-bit PCI bus slots.

Flash Memory

−Supports flash memory functionality.

−Supports ESCD functionality.

Built in IDE Facilities

−Supports four IDE hard disk drives.

−Supports PIO Mode 4, Master Mode, and high performance hard disk

drives.

−Supports disk transfer rates up to 100 MB/second.

−Supports Ultra DMA 33, Ultra DMA 66, Ultra DMA 100 Bus Master

Modes.

−Supports IDE interface with CD-ROM.

−Supports high capacity hard disk drives.

−Supports LBA mode.

AC’97 Sound Codec Onboard

−AC-LINK protocol compliance.

−Compliant with AC’97 2.2 specification.

−18-bit full duplex stereo ADC, DACs.

−SNR>95 dB through mixer and DAC.

−AC-3 playback required for PVD applications.

Chapter 1 Motherboard Description

1-4

Onboard Graphic

−High Performance and High Quality 3D Accelerator:

Built-in a high performance 256-bit 3D engine.

Built-in a high quality 3D engine.

−High Performance 2D Accelerator.

−MPEG-2/1 Video Decoder:

MPEG-2 ISO/IEC 13818-2 MP@HL and MPEG-1 ISO/IEC 11172-2

standards compliant.

Built-in advanced hardware DVD acceleration logic.

Support AGP bus master/LFB-mode code fetching.

Half pixel resolution in motion compensation.

Support VCD, DVD and HDTV (all ATSC modes) decoding.

Direct DVD to TV playback.

−Video Accelerator.

−High Integration:

Built-in 64x128 CRT FIFOs to support ultra high resolution graphics

modes and reduce CPU wait-state.

I/O facilities

−One multi-mode Parallel Port capable of supporting the following

specifications:

Standard & Bidirection Parallel Port.

Enhanced Parallel Port (EPP).

Extended Capabilities Port (ECP).

−Supports one serial ports, 16550 UART.

−Supports Infrared Data Transmission using IrDA.

−Supports 360KB, 720KB, 1.2MB, 1.44MB, and 2.88MB floppy disk

drives.

Universal Serial Bus

−Supports two back panel Universal Serial Bus Ports and four front panel

Universal Serial Bus Ports (optional).

−Supports 48 MHz USB.

Chapter 1 Motherboard Description

1-5

BIOS Hardware Monitor Function

−Monitors CPU Fan Speed.

−Monitors System Fan Speed.

−Monitors System Voltage.

Dimensions (Micro ATX form-factor)

−24.5cm x 24.5cm (WxL)

Otros manuales para M7SXG

Tabla de contenidos

Otros manuales de Placa madre de Biostar

Biostar

Biostar A960D+V2 Guía del usuario

Biostar

Biostar M7 VKQ Manual de usuario

Biostar

Biostar M7MIA Manual de usuario

Biostar

Biostar P4VTC Manual de usuario

Biostar

Biostar P4 VTB Manual de usuario

Biostar

Biostar TFORCE4 SLI Guía del usuario

Biostar

Biostar ta320-btc Manual de usuario

Biostar

Biostar B75MU3 Guía del usuario

Biostar

Biostar P4 TSE-D2 Manual de usuario

Biostar

Biostar TZ590-BTC DUO Manual de usuario

Biostar

Biostar TA970XE Guía del usuario

Biostar

Biostar P4 SDL Manual de usuario

Biostar

Biostar P4TCA PRO Guía del usuario

Biostar

Biostar Hi-Fi B85N 3D Guía del usuario

Biostar

Biostar P4 SDL Manual de usuario

Biostar

Biostar M7VIT Bravo Guía del usuario

Biostar

Biostar H81A Guía del usuario

Biostar

Biostar Hi-Fi Z170Z5 Manual de usuario

Biostar

Biostar A75MH Guía del usuario

Biostar

Biostar A880G Guía del usuario

Biostar

Biostar A55MLV2 Manual de usuario

Biostar

Biostar A57A2 Guía del usuario

Biostar

Biostar B560MX-E PRO Manual de usuario

Biostar

Biostar MCP6P-M2 Guía del usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario