Biamp Apprimo Touch 8i Manual de usuario
Apprimo Touch 8i - Overview
Details
The Apprimo Touch 8i is an 8" control panel for any room requiring an advanced level of control while still being a stylish
and discreet interface that fits any type of interior design.
FEATURES
• Control up to 20 IP-based devi
• 8" capacitive touch LCD interface
• Scratch-resistant glass
• Display brightness can adjust automatically to the ambient light level
• Customizable user interface to fit customers’ control requirements and corporate identity
• PoE powered (IEEE 802.3at Class 3, 15W) for simple, single CAT5e/CAT6 cable installation
• Fits standard single gang US, EU, and DK back boxes
CONTENTS
• Apprimo Touch 8i (with table mount attached)
• Reset Pin
• 3m (10ft) Cat5 cable
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 1
Installation and operation guide
Apprimo user interfaces are designed and configured via our Project Designer software.
•Apprimo 8i install guide.pdf
Table installation
1. Remove the cover from the bottom of the
table mount.
2. Plug the network cable into the rear port.
3. Route the cable through the notch in the
latch and stand and reattach the cover.
4. Follow on-screen prompts to complete the
installation.
Wall mounting (optional accessories)
Note: The control panel may be mounted to the wall with or without a gang box.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 2
1. The center of the control panel would typically be
located between 102 – 165 cm (40" – 65") above the
finished floor. Follow local guidelines for accessible
wall controls. Route Cat 5e/6 cable to the location.
There is a channel on the base plate and a knockout
on the angled plate for cable routing if installed on a
solid wall.
Note: For installations complying with US
ADA guidelines the top of the panel should
not exceed 122 cm (48") from the floor.
2. Remove the cover from the rear of the table
mount.
3. Remove the screw holding the table mount to the
control panel.
4. Remove the mount by sliding it down and then lifting it.
5. Attach the wall plate directly to the wall with screw anchors or screw it to a gang box (most gang box
styles are
supported). Orient the plate with the arrows pointing up.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 3
6. Attach the wall mount base to the control panel - fit clips into the control panel back (a), and slide up (b).
7. Secure the base with a screw.
8. Insert the network cable into the port in the back of the control panel.
9. Mount the panel on the wall plate by hanging it on the top tabs then rotating in and clipping it into the
bottom tab. Ensure the tab is fully engaged (see circled views).
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 4
Operation
Touch the control panel to wake it up. It provides a method of interacting with or controlling the room system. To
program in Biamp Project Designer software, create a new project and select the Apprimo Touch 8i from the touch panel
controllers list.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 5
A project can then be created using a blank layout or one of the provided templates.
Note: The IP address can be found either by automatic LAN lookup in Project Designer, directly on the screen if no
project is currently uploaded, or in the setup menu of the Apprimo Touch 8i that can be accessed with the pinhole
button.
Settings/reboot
To bring up the device settings screen, insert the reset pin into the designated hole at the top of the control panel rear
and press lightly. To initiate a device reboot, insert the reset pin into the other hole and press lightly.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 6
Otros manuales para Apprimo Touch 8i
2
Tabla de contenidos
Otros manuales de Panel de control de Biamp
Biamp
Biamp IMPERA SIERRA II Manual de usuario
Biamp
Biamp Apprimo Touch 8i Instrucciones de funcionamiento
Biamp
Biamp Vocia WR-1 Manual de usuario
Biamp
Biamp TEC-X 2000 Instrucciones de funcionamiento originales
Biamp
Biamp RP-S4 Manual de usuario
Biamp
Biamp Apprimo Touch 8i Instrucciones de funcionamiento
Biamp
Biamp TEC-X 1000 Instrucciones de funcionamiento originales
