BFW Daymark Manual de usuario
LED Headlight
Operating Manual
DaymarkTM
Table of Content
Symbol Description .....................................................................................2
Warnings and Cautions................................................................................3
Intended Use ............................................................................................................... 4
Unintended Uses ......................................................................................................... 4
Overview.....................................................................................................5
System Description ...................................................................................................... 5
Assembly and Operation .............................................................................6
Ferrite .......................................................................................................................... 6
Headlight ..................................................................................................................... 7
Classic Headband......................................................................................................... 8
Key West Headband .................................................................................................... 8
Controller..................................................................................................................... 9
Battery ....................................................................................................................... 10
Charging the Battery.................................................................................................. 11
Linkage Assembly ...................................................................................................... 12
Removing the Headlight ............................................................................................ 13
Mounting the Headlight ............................................................................................ 14
Cleaning and Maintenance ........................................................................17
Headlight ................................................................................................................... 17
Specifications ............................................................................................18
Electromagnetic Compatibility...................................................................19
Troubleshooting and Service .....................................................................23
Warranty and Service ................................................................................................ 23
2
Symbol Description
These important symbols may appear on your Long Island Technology Group Optic Headlight. Please note their
meaning.
Attention: Read this owner’s manual for all warnings, precautions and instructions for use.
CE marking of conformity indicates this device complies with European Directive 93/42 EC
on medical devices and Directive 2002/95/EC on the restriction of the use of certain hazard-
ous substances in electrical and electronic equipment.
The UL mark indicates this product has been tested to, and conforms to applicable stan-
dards.
More information for this product can be found in this operating manual.
AS TO ELECTRICAL SHOCK, FIRE AND MECHANICAL HAZARDS ONLY
IEC 60601-1 Edition 4, IEC 60601-1-2 Edition 3,
ANSI/AAMI E-S60601-1 (2005), CAN/CSA-C22.2 No. 60601-1 (2008)
3
Warnings and Cautions
Users of this product should be thoroughly trained in the appropriate medical procedures. Also they should
read and understand this owner’s manual for this headlight and all equipment used with it.
!WARNING! NEVER direct the device light beam into the eyes of anyone. Strong light emied from the
device can cause damage or injury.
!Read and understand the Device Operang Manual before using the device.
!Avoid prolonged physical contact with the headlight during use as it may be warm.
!Standard Working Distance is 16 inches (40 cm) minimum. Use cauon when operang at closer dis-
tances.
!DO NOT use devices for direct illuminaon of the eye.
!DO NOT use mulple units simultaneously to illuminate the same area. High intensity illuminaon can
harm ssue.
!Use DaymarkTM only with BFWTM/Long Island Technology GroupTM products or accessories.
!RX Only: United States Federal Law restricts this device to sale by or on the order of a health care pro-
fessional.
!DO NOT subject the DaymarkTM to strong shocks, which include but are not limited to dropping the
device on the oor.
!DO NOT use this device for anything other than its intended use.
!DO NOT modify this equipment.
!DO NOT open device. No serviceable components are inside device.
!Only Qualied Personnel should operate the BFWTM DaymarkTM
!DO NOT submerge the device or any of its components in liquid.
4
Warnings and Cautions
!DO NOT use if packaging is damaged.
!USE ONLY components and accessories listed on page 5 and 18 of this manual. Failure to do so may
decrease system performance, may lead to unsafe operaon, may negavely aect EMC performance
and could result in non-compliance and could void the warranty
!WARNING Use of this equipment adjacent to or stacked with other equipment should be avoided
because it could result in improper operaon. If such use is necessary, this equipment and the other
equipment should be observed to verify that they are operang normally.
!WARNING Portable RF communicaons equipment (including peripherals such as antenna cables and
external antennas) should be used no closer than 30 cm (12 inches) to any part of the DaymarkTM, in-
cluding cables specied by the manufacturer. Otherwise, degradaon of the performance of this equip-
ment could result.
!Medical Electrical Equipment needs special precauons regarding EMC and needs to be installed and
put in service according to the EMC informaon in the Electromagnec Capability of this manual.
Intended Use
The BFWTM DaymarkTM LED Headlight is a device intended to supply supplemental, constant and con-
trolled illumination during medical procedures. This device is designed for use in the operating room. The
advantage of the DaymarkTM system is that the light is positioned between the medical professional’s eyes and
the direction of illumination is always in the exact direction of the medical professional’s vision. The intended
environment for use is for Professional Health Care except for near active HF Surgical Equipment and the RF
shielded room of an ME System for magnetic resonance imaging. Please follow the assembly instructions on
page 6 and maintenance instructions on page 17 in order to maintain basic safety.
5
Overview
System Descripon
The BFWTM DaymarkTM LED Headlight is constructed of durable plastic housing encasing a precision
aluminum lens system holder with glass anti-reflective coated lenses and a spot size adjusting iris. Light is
provided by a high power LED, driven by a solid state controller and battery to provide ON/OFF and 5 levels of
light output. The system includes two spare batteries and a battery charging system. The device is articulated,
allowing the lower part of the light to be turned left and right for ease of aiming.
As shown below the device is attached to a headband, which allows the medical professional to wear the
headlight on their head. The headband mounting system adjusts for comfortable fit and allows the light to be
adjusted for position between the user’s eyes so illumination is shadow free.
Two styles of headbands are available, the Classic headband as shown below, constructed of plastic with knobs
for size adjustment, and the Key West headband, designed to be lighter and more comfortable. (not shown)
ABC
D
EF
G
A. DaymarkTM LED Headlight
B. Headband (accessory)
Classic Headband (shown above)
Key West Headband (not shown)
C. Power Cable
D. Battery
E. Battery Holster/Controller
F. Battery Charger (Regular Shown)
G. Battery Charger Power Supply
6
Assembly and Operation
Ferrite
1. Open the Ferrite by pulling on the tab.
2. Attach the provided Ferrite onto the Power Cable close to the connector over-mold.
!DO NOT use the DaymarkTM without the Ferrite as it may result in non-compliant EMC levels.
7
Assembly and Operation
Headlight
A
B
CD
A. Headlight Front Lens
B. Iris Adjustment Ring
C. Power Cable
D. Mounting Linkage
DaymarkTM Operation:
1. The lower portion of the headlight (below the Iris Adjustment Ring) can be turned a small
amount to the left and right to facilitate aiming the light.
2. The Iris Adjustment Ring (B) allows for variation of the spot size projected by the headlight. The Mounting
Linkage (D) is adjustable for vertical aiming and position adjustment.
8
Assembly and Operation
Classic Headband
A
Key West Headband
B
A
A. Adjustment Knobs
Classic Headband Adjustment:
1. Turn the Adjustment Knobs (A) to tighten or loos-
en the headband.
A. Adjustment Tab
B. Release Button
Key West Headband Adjustment:
1. To tighten pull on the Adjustment Tab (A).
2. To loosen press the Release Button (B) and pull
on the front of the headband away from the
back.
Tabla de contenidos
