BFT Lux BT QSG Manual de usuario

Lux BT QSG

(see also Thalia P or Libra CLX QRG)

Quick reference guides are not a replacement for the supplied instructions, they are supplementary

Read and understand the installer warnings in the main instruction document first

Always apply good, safe, state of the art engineering and electrical installation principles

Safety of the completed installation is the ultimate responsibility of the installer

This product is not suitable for DIY use and should only be installed and maintained by a trained, skilled, professional installer

Geometry

This motor will work best when A = B, any other configuration will detract

from its performance and could affect reliability

Lux BT – A = 135mm B = 135mm C = 1050mm

Lux G BT – A = 195mm B = 195mm C = 1295mm

Geometry

Extreme difference between A and B should be avoided at all

cost, and will only work on the lightest gates in perfect locations

and with perfect set up

End of Stroke Limit

The rams need a

degree of travel left un

used in the open and

closed positions

If these dimensions are

exceeded the encoder

will not accept the limit

positions and give ER

SU during the set up

procedure

Length, Weight and Locks

Leaf weight/length should not exceed;

Lux BT 300Kg/2m

Lux G BT 800Kg/3m

300kg/5m

Where the G BT is used on gates over 3m length, it must be used in

non locking form. Turn both valves fully anti clockwise after set up

Ground stops are recommended in the open and closed positions.

Neither motor is recommended for use with wind affected gates.

Open and Close locks are

provide on either side of the

release valve

10 11 14 15 41 42 43

Wiring

Libra CLX Thalia P

Use 3 core externally rated flex in accordance with

BS7671

1.5mm2 up to 10m

2.5mm2 up to 20m

Method Libra CLX

Fit the motors and check the end of stroke limits

Close the gates and lock off

Wire in the motors

Run “LSU ADJ” (the aim is to stop at the stop, not hit the stop)

•Press and hold top button – lift off at open point – “OK” (M2 Open)

•Press and hold top button – Lift off at open point “OK” (M1 Open)

•Press and hold middle button – Lift off at close point “OK” (M1 Close)

•Press and hold middle button – Lift off at close point “OK” (M2 Close)

Run “AUTOSET”

Increase N1T and N2T to 25%

Increase SLOW SPEED to 35%

Fit accessories one at a time and test each before moving on

Method Thalia P

Fit the motors and check the end of stroke limits

Close the gates and lock off

Wire in the motors

Run the quick menu – Press OK once

Follow the prompts to “LSU ADJ”

•Press and hold top button – lift off at open point – “OK” (M1 Open)

•Press and hold top button – Lift off at open point “OK” (M2 Open)

•Press and hold middle button – Lift off at close point “OK” (M2 Close)

•Press and hold middle button – Lift off at close point “OK” (M1 Close)

Run “AUTOSET”

Increase OPEN FORCE and CLOSE FORCE to 25%

Increase SLOW SPEED to 35%

Fit accessories one at a time and test each before moving on

Adjust close delay to give 700mm min. between M2 and M1 at closing

Adjust slow speed to cut in at 700mm from closed

Measure force/time at 500mm distance in line with the motor

Thalia P;

Increase close force & slow speed to just below 150N

Libra CLX;

Adjust N2T and SLOW speed to just below 150N

Run a full set of tests

Address all other risks as appropriate

MD Compliance

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de apertura de puertas de BFT

BFT

BFT BOTTICELLI Manual de usuario

BFT

BFT VISTA SW 260 SXL Manual de usuario

BFT

BFT BRCT Manual de usuario

BFT

BFT VISTA SW SXL Manual de usuario

BFT

BFT MOOVI GA Manual de usuario

BFT

BFT OBERON TRI A2000 INV Manual de usuario

BFT

BFT FR95 Series Manual de usuario

BFT

BFT BOTTICELLI SMART BT A 850-1250 Manual de usuario

BFT

BFT VISTA EMERGENCY Manual de usuario

BFT

BFT KIT P.B. BL-SMALL XTREME 35 Manual de usuario

BFT

BFT VISTA-SLE Manual de usuario

BFT

BFT Q.BO KEY Manual de usuario

BFT

BFT VISTA SW SXL Manual de usuario

BFT

BFT WIND RMB 130B 200 Manual de usuario

BFT

BFT EOS Manual de usuario

BFT

BFT VIRGO Manual de usuario

BFT

BFT VISTA-SL Series Manual de usuario

BFT

BFT RTD Manual de usuario

BFT

BFT ARGO Manual de usuario

BFT

BFT CLONIX1 Manual de usuario

BFT

BFT PHOBOS BT A25 Manual de usuario

BFT

BFT SUB EL Manual de usuario

BFT

BFT ELI-250 Manual de usuario

BFT

BFT PEGASO B CJA 6 25 L01 Manual de usuario

Manuales populares de Sistema de apertura de puertas de otras marcas

Pamex

Pamex KT-INP35 Manual de usuario

Label

Label NEPTIS/LE Manual de usuario

Cal-Royal

Cal-Royal N-F77CVR Manual de usuario

Scrigno

Scrigno OPEN1000 Manual de usuario

TriMark

TriMark UM 34 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Besam

Besam Swingmaster MP Guía

CRL

CRL SENIOR PRIMA Manual de usuario

Assa Abloy

Assa Abloy SARGENT 1431 Series Manual de usuario

GAL

GAL MOVFR Hoja de especificaciones

Olide

Olide 120B Manual de usuario

Normstahl

Normstahl IDO7 Manual de usuario

Häfele

Häfele Finetta T 70 VF Manual de usuario

AGS

AGS D-PL Manual

Stanley

Stanley MA900ñ Instrucciones de instalación

WITTUR

WITTUR Hydra Plus UD300 Manual

Alutech

Alutech TR-3019-230E-ICU Instrucciones de instalación y funcionamiento

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Hoja de especificaciones