BFE Esprit ET188 Manual de usuario
ESP0016
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW TREADMILL!
Z100 / Z300 Z500 Z700
OWNER’S MANUAL
ET188
Treadmill
ET188
1
Product Registration………………………………………………………………………..2
Important Safety Instructions…………………………………………………………….. 3
Important Electrical Information………………………………………………………….. 4
Important Operation Instructions…………………………………………………………. 5
Assembly instructions………………………………………………………………………6
Operation of Your New Treadmill………………………………………………………….9
General Maintenance.……………….……………………………………………………..12
Service Checklist - Diagnosis Guide…………………………………………………….. 15
Manufacturer’s Limited Warranty………………………………………………………….16
Table of Contents
ET188
2
Thank you for your purchase of this quality treadmill. Your new treadmill was
manufactured by one of the leading fitness manufacturers in the world and is backed by
one of the most comprehensive warranties available.
Please take a moment at this time to record the name of the dealer and the date of
purchase below to make any future, needed contact easy. We appreciate your support
and we will always remember that you are the reason that we are in business.
Yours in Health,
BOYLES FITNESS Equipment Pty Ltd.
Name of Dealer______________________________________
Purchase Date_______________________________________
ET188/ESP0016_ver.A
CONGRATULATIONS ON YOUR
NEW TREADMILL AND WELCOME
TO THE SPIRIT FAMILY!
ET188
3
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your treadmill from the electrical
outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the
treadmill on a flat level surface with access to a 240-volt, 10-amp grounded outlet.
DO NOT USE AN EXTENSION CORD UNLESS IT IS 14AWG OR BETTER, WITH ONLY ONE
OUTLET ON THE END. The treadmill should be the only appliance in the circuit in which it is
connected. DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING IMPROPER
ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET. A serious shock or fire hazard may
result along with computer malfunctions. See Grounding Instructions, page 3.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both
carpet and treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance
between the rear of the treadmill and any fixed object.
Keep children away from the treadmill. There are obvious pinch points and other
caution areas that can cause harm.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not working
properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, remove tether cord, then remove the plug
from the outlet.
Do not attempt to use your treadmill for any purpose other than for the purpose it is
intended.
The pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Remove tether cord after use to prevent unauthorized treadmill operation.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
Important Safety Instructions
ET188
4
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Large
switching currents of the drive motor will trip GFCI type outlets, as any appliance with a
large motor will. Route the power cord away from any moving part of the treadmill
including the elevation mechanism and transport wheels.
NEVER remove any cover without first disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your treadmill may be
affected. Such conditions are not covered under your warranty. If you suspect the
voltage is low, contact your local power company or a licensed electrician for proper
testing.
NEVER expose this treadmill to rain or moisture. This product is NOT designed for use
outdoors, near a pool or spa, or in any other high humidity environment. The operating
temperature specification is 40 to 120 degrees Fahrenheit and humidity limit is 95%,
non-condensing (no water drops forming on surfaces).
This product must be grounded. If the treadmill should malfunction or breakdown, proper
grounding provides a path of least resistance for electric current, reducing the risk of electric
shock. This product is equipped with a cord having an equipment-grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in
doubt as to whether the product is properly grounded. Do not modify the plug provided
with the product if it will not fit the outlet; have a proper outlet installed by a qualified
electrician.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like
the plug illustrated below. A temporary adapter that looks like the adapter illustrated below
may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded
outlet is not available. The temporary adapter should be used only until a properly grounded
outlet, (below) can be installed by a qualified electrician. The green colored rigid ear-lug, or the
like, extending from the adapter, must be connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal
screw.
Important Electrical Information
Grounding Instructions
Grounded Outlet
Grounding Pin Grounded Outlet Box
Metal Screw
Adapter
Tab of
Grounding
Screw
ET188
5
NEVER operate this treadmill without reading and completely understanding the results of any
operational change you request from the computer.
Understand that changes in speed and incline do not occur immediately. Set your desired
speed on the computer console and release the adjustment key. The computer will obey the
command gradually.
NEVER use your treadmill during an electrical storm. Surges may occur in your household
power supply that could damage treadmill components.
Use caution while participating in other activities while walking on your treadmill; such as
watching television, reading, etc. These distractions may cause you to lose balance or stray
from walking in the center of the belt, which may result in serious injury.
NEVER mount or dismount the treadmill while the belt is moving. the treadmills start with at a
very low speed and it is unnecessary to straddle the belt during start up. Simply standing on
the belt during slow acceleration is proper after you have learned to operate the unit.
Always hold on to a handrail or hand bar while making control changes (incline, speed, etc.).
A safety tether cord is provided with this unit. It is a simple magnetic design that should be used at
all times. It is for your safety should you fall or move too far back on the tread-belt.
Pulling this safety tether cord will stop tread-belt movement.
To Use:
1. Place the magnet into position on the round portion of the console control head. Your treadmill
will not start and operate without this. Removing the magnet also secures the treadmill from
unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note: The
magnet has strong enough power to minimize accidental, unexpected stopping. The clip should be
attached securely to make certain it does not come off. Be familiar with its function and limitations.
The treadmill will stop, depending on speed, with a one to two step coast anytime the magnet is
pulled off the console.
Safety Tether Cord
Important Operation Instructions
ET188
6
ASSEMBLY PACK CHECK LIST
#84
-
5/16” x 1/2”
Button Head Socket Bolt (2pcs)
#37 - Safety Key (1pc)
#69
-
5/16” x 18mm
Flat Washer (6pcs)
#71
-
3/8” x 19mm
Flat Washer (2pcs)
#86 - 13/14 mm Wrench (1pc) #85 - M5/M6 Allen Wrench (1pc)
#87 - Lubricant (1pc)
#65
-
3/8”
Nyloc Nut (2pcs)
#55
-
3/8” x 46mm
Button Head Socket Bolt (2pcs)
#83
-
5/16” x 3”
Button Head Socket Bolt (4pcs)
#94
-
Short Phillips Head
Screw Driver (1pc)
#60
-
M5 x 15mm
Phillips Head Screw (4pcs)
(These four screws are attached
to the back of the console)
ET188
7
STEP 1
Remove all the parts from the carton.
STEP 2
Raise the upright supports into place as shown. Secure the uprights with the four 5/16” x
3” socket head bolts (83) and 5/16” flat washers (69).
Assembly Instructions for ET188
ET188
8
STEP 3
Install, and just hand tighten for now, the two 5/16” x 1/2“ socket head bolts (84) and
5/16” flat washers (69) into the front of the left and right upright tubes. Now install the 3/8”
x 46mm socket head bolts (55) from the outside of the upright tubes, 3/8” flat washers
(71) and 3/8” nuts from the inside of the uprights and tighten all four bolts as tight as
possible.
STEP 4
Connect the computer cable (38) and pulse sensor wires (93) to the mating connectors
on the back of the console. Secure the console in place with the four M5 x 15mm screws
(60).
ET188
9
GETTING STARTED:
Power the treadmill on by plugging it into a grounded wall outlet, then turn on the power switch
located at the front of the treadmill below the motor hood. Ensure that the safety key is installed,
as the treadmill will not operate without it.
When the power is initially turned on, the display will light up and then show an Odometer and
Time reading. The odometer reading shows how many virtual miles the treadmill gone and Time
shows how many hours it has been in use. The display will also show a software version; i.e. VER
1.0. The console will now be in idle mode, which is the starting point for operation.
QUICK START:
After the treadmill is powered on and the safety key is in place simply press the START key. The
treadmill will start at the minimum speed of 1 kmph, the time will count up from zero and all data
will begin to accrue. You can adjust the speed manually by pressing the Fast and Slow buttons or
the Quick Keys labeled: Walk (3 kmph), Jog (6 kmph) and Run (9 kmph).
Operation of Your Treadmill
Tabla de contenidos
Otros manuales de Rueda de andar de BFE
Manuales populares de Rueda de andar de otras marcas
Smooth Fitness
Smooth Fitness EVO 3i Manual de usuario
NordicTrack
NordicTrack NETL81810.0 Manual de usuario
Schwinn
Schwinn 830/Journey 8.0 Manual de usuario
Keys Fitness
Keys Fitness HealthTrainer HT-740T Manual de usuario
Spirit
Spirit XT8 Manual de usuario
NordicTrack
NordicTrack T 14.0 Treadmill Manual de usuario