BEYES ApexPilot G2 Manual de usuario

Cordless Endo Motor

Instruction for Use

Note: The description on reciprocating mode is only applicable for the

device that has reciprocating mode.

1. Introduction

1.1 Features

• Use of brushless motor - low noise and long lifetime

• Cordless

• Contra angle with 360° rotation

• Built-inleparameters

• 15 memory setting

• Auto apical reverse/stop

• Large LCD display

• Connectable to Accurator A2, apex locator

1.2 Intended use

1.2.1 This device can be used for preparation and enlargement of root canals.

1.2.2 This device should only be operated by licensed dental professionals

ApexPilot G2 is mainly used for Endodontic treatments. It can be used as an endo

motor for preparation and enlargement of root canals.

1.3 Contraindication

• Patient or doctor with a pacemaker

• Patient with hemophilia

• Patient with heart disease

• Pregnant women or young

Table of Contents

1. Introduction.......................................................................................... 2

2. Warning and Safety............................................................................. 4

3. Installation ........................................................................................... 5

4. Operation............................................................................................. 7

5. Screen Display .................................................................................... 11

6. Automatic Reverse Function ............................................................... 14

7. Apex Locator ....................................................................................... 15

8. Troubleshooting................................................................................... 20

9. Cleaning, Disinfection and Sterilization ............................................... 20

10. Storage, maintenance and transportation ......................................... 22

11. Environmental Protection .................................................................. 23

12. Signs.................................................................................................. 23

13. Statement .......................................................................................... 24

14. Beyes Limited Warranty Statement................................................... 24

15.TechnicalSpecication...................................................................... 26

16. EMC-Declaration of conformity.......................................................... 27

1.4 Package includes

Motor handpiece Contra angle

Charging base Nozzle Power adapter

• O-ring

• Silicon cover

• Mini 8P cable

• Instruction manual

Diagram of components and control buttons

2. Warning and safety

Warning

• First read this instruction manual before operating this device

• This device should only be operated by licensed dental professionals

• Do not directly or indirectly place this device near heat source.

• Operate and store this device in reliable environment.

• This device requires special precautions regarding electromagnetic compatibility

(EMC) and must be in strict accordance with the EMC information for installation

anduse.Donotusethisequipmentespeciallyinthevicinityofuorescentlamps,

radio transmitting devices, remote control devices, handheld and mobile high-

frequency communication devices.

• Extended time use of Reciprocating Mode may result in motor overheat

• Use the original contra angle

• Do not make any changes to the device. Any changes may violate safety

regulations, causing harm to the patient

• Use original power adapter. Other power adapter will result in damage to lithium

battery and control circuit.

• The motor handpiece cannot be autoclaved. Use disinfectant of neutral pH value

or ethyl alcohol to wipe its surface.

• Do not remove contra angle before motor stops. It would cause damage to

handpiece and contra angle.

• Securethelebeforestarting

• Settorqueandspeedaspertherecommendedspecicationsofle

manufacturer.

• Follow instruction in this manual to replace battery and only replace with original

lithium battery.

• Remove battery from the handpiece before long-term storage

• Do not touch handpiece or charging base for more than 10 sec during charging.

Heat builds up while charging.

Safety

• Donotusedeviceinthepresenceofaammableanestheticmixturewithair,

oxygen, or nitrous oxide.

• Do not continuously use contra angle with patient longer than 10 minutes. The

temperature of contra angle may reach 46.6°C. Allow time to cool down before

further use.

3. Installation

3.1 Battery

Handpiece has built-in lithium battery. Battery charges wirelessly through the base.

• Plug in power adapter and connect it to the charging base

• Seat handpiece on the charging base

• Bluelightwillbeashingwhiledeviceischarging

• Blue light will stay on when fully charged

3.2 Contra angle

• The contra angle adopts precision gear transmission, and the transmission ratio

is 6:1.

• CleananddisinfectwithdisinfectantofneutralPHvaluebeforetherstuse.

• Clean and disinfect after each patient use

• Sterilize under 134°C, 2.0~2.3bar (0.20~0.23MPa).

• ContraangleinpackageonlytsApexPilotG2.Itdoesnottotherhandpieces.

Installation of contra angle

• Align any locating pin of the contra

angle with the positioning slot on the

motor handpiece and push in the

contra angle horizontally.

• The three locating pins on the

contra angle are inserted into the

three positioning slots on the motor

handpiece.

• A “click” sound indicates that the

installation is in place.

• The contra angle can be rotated 360°

freely.

Removal of contra angle

Pull out the contra angle horizontally when the motor handpiece is turned off.

Warning

After installation, give the contra angle a light tug to make sure that it is securely

attached before starting motor.

Stop the motor before plugging in or pulling out the contra angle.

3.3 File

Installationofle

1.Insertleintothechuck

2. Push button

3.Rotateletotthelatchgrooveandslipin

4.Releasepushbuttontolockle

5.Pullletoensuresecurity

Note:

OnlyuseleswithshanksthatmeettheISOstandard.(ISOstandard:Ø2.334–

2.350 mm)

Warning

Insertandremovelewithoutholdingthepushbuttonmaydamagethechuckof

contra angle.

Removal of le

1. Press and hold the push button

2.Pulloutthele

Warning

•Stopmotorbeforepluggingandpullingoutthele.

•Removingleswithoutholdingthepushbuttonwilldamagethechuckofcontra

angle.

•Usecautionwheninsertingandremovinglestoavoidinjurytongers

4. Operation

Press Main to turn on device to

Standby screen

Warning:

In custom setting, all parameters

shouldfollowthelerequirementfor

proper operation.

Press Main to start motor

Operating screen

Motor runs with set speed and torque

Moving bars from bottom up shows the

letorque.

Press Main to stop motor

Standby screen

Hold “P” and press Main to turn off

device

4.1 Start and stop operation

Standby screen

Press “+”/”-“ to change screen among

M0-9

Press “P” to show operating mode and

available parameter.

Operating Mode

Blinking is the current mode and ready

to change

Press “+”/”-“ to change among

CW, CCW, REC, ATR

Press “P” to show available parameters

for selected mode

Or press Main to exit to accept the

mode without changing the parameters

Parameter 1

Blinking is the current setting Press

“+”/”-“ to change number

(Press and hold “+”/”-“ speed up the

number changing)

Number reaching highest goes back to

lowest. Vice versa.

Press “P” to accept and go to the next

available parameter

Or press Main to accept and exit

without going to next parameter

Parameter 2

Blinking is the current setting Press

“+”/”-“ to change number

(Press and hold “+”/”-“ speed up the

number changing)

Number reaching highest goes back to

lowest. Vice versa.

Press “P” to accept and go to the next

available parameter

If no more available parameter, the

screen goes back to mode screen.

Steps can be repeated.

Press Main to accept and exit without

going to next parameter

4.2 Store setting on M0-9

M0-M9 is a memory program to store Operation mode and associated parameter.

Standby screen

Press “+”/”-“ to change screen passing

M0 or M9

Thescreenshowslenameandsize

instead of M0-9

Keep pressing “+”/”-“ to show 5 storage

locations.

Select the location to make change

Pressandhold“P”toenterlelist

File list

Press“+”/”-“toscrollandselectthele

Press “P” to show list of pre-set

parameters

Or press Main to accept and exit

without selecting parameters

Pre-set parameters

Press“+”/“-“toscrollandselectle

size

Press “P” to accept and back to File

lists

Or press Main to accept and back to

standby

Standby screen

Parametersissettoledefault

parameter

Warning:

Changing the default parameter for

selectedleisnotrecommended.

In the case that any parameter is

changed, press and hold “P” to repeat

stepstore-selectthele.

4.3 Store setting with build-in le system

4.4 Set handpiece functions

Turn off device

Hold “P” and press Main to enter function setting

Software version (unchangeable)

Screen show Auto Power Off in 2 sec

Auto Power Off

Press “+”/”-“ to change between 3 to 30 min

Press “P” to accept and go to next setting

or Press Main to accept and exit

Auto Standby Scr

Press “+”/”-“ to change between 3 to 30 min

Press “P” to accept and go to next setting

or Press Main to accept and exit

Dominant Hand

Press “+”/”-“ to switch between Left and Right

Press “P” to accept and go to next setting

or Press Main to accept and exit

Calibration

Note:

Calibration should be performed when

replacing contra angle

Press “+”/”-“ to switch between ON and OFF

Pluginoriginalcontraanglewithoutle.

Warning:

Use original contra angle only.

Any load applied to contra angle will be

offset. And calibration will not be correct.

Press “P” to accept and go to next setting

or Press Main to accept and exit

If set ON, calibration will be performed when

exiting. And setting will then switch back to

OFF.

Tabla de contenidos

Otros manuales de Equipo dental de BEYES

BEYES

BEYES AirLight M800 Manual de usuario

BEYES

BEYES AirLight M800 Manual de usuario

BEYES

BEYES Accurator A2 Manual de usuario

BEYES

BEYES APEXPILOT ALL-IN-ONE Manual de usuario

BEYES

BEYES Maxso High Speed M200 Manual de usuario

BEYES

BEYES Maxso X99 Series Manual de usuario

BEYES

BEYES Comfort-Sonic P9 Manual de usuario

BEYES

BEYES AirLight M800 Manual de usuario

BEYES

BEYES AirLight Highspeed Handpiece Series Manual de usuario

BEYES

BEYES Comfortek Manual de usuario

BEYES

BEYES Maxso E600P Manual de usuario

BEYES

BEYES ApexPilot G1 Manual de usuario

BEYES

BEYES EndoPilot Manual de usuario

BEYES

BEYES Maxso X200 Manual de usuario

BEYES

BEYES SLimax-C Manual de usuario

BEYES

BEYES Maxso E600 Manual de usuario

BEYES

BEYES GPRO P1 Manual de usuario

BEYES

BEYES Comfort-Sonic P6 Plus Manual de usuario

Manuales populares de Equipo dental de otras marcas

Vatech

Vatech EzRay Air VEX-P300 Manual de usuario

KaVo

KaVo GENTLEpower LUX Contra-angle 25 LP Manual de usuario

DENTSPLY

DENTSPLY SmartLite Focus Manual de usuario

LM ProPower CombiLED Manual de usuario

Owandy Radiology

Owandy Radiology RX-AC Manual de usuario

mectron

mectron Piezosurgery Manual de usuario

Belmont

Belmont CREDIA G1 Manual de usuario

Planmeca

Planmeca Sovereign Classic Manual de usuario

Bego

Bego Fornax T Manual de usuario

Renfert

Renfert SYMPRO Guía rápida

Ateco

Ateco AT-301 Manual de usuario

Nevadent

Nevadent NZPS 3 A1 Manual de usuario

Muss Dental

Muss Dental MA 50 Manual técnico

Diplomat

Diplomat Comfort Series Manual de usuario

Dentatus

Dentatus Nyström Manual de usuario

OMS

OMS DUKE EASY Manual

OMS

OMS LINEA PATAVIUM Manual

BRYANT DENTAL

BRYANT DENTAL Ignis Gesture A-494322 Manual de usuario