Beyerdynamic Opus 910 Manual de usuario

OPERATING INSTRUCTIONS

Opus 910

Wireless UHF System

CONTENTS

OPERATING INSTRUCTIONS Opus 910

Important Safety Information . . . . . . . . . . . . . . . . . . . Page 4

NE 911 / 912 / 914 Diversity Receiver . . . . . . . . . . . . . Page 8

ZAS 900 Antenna Splitter . . . . . . . . . . . . . . . . . . . . . . Page 16

Connection to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . Page 18

S 910 C / S 910 M Handheld Transmitters . . . . . . . . . Page 19

TS 910 Beltpack Transmitter . . . . . . . . . . . . . . . . . . . . Page 26

General Instructions for all Transmitters . . . . . . . . . . . Page 32

Trouble Shooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 33

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 34

Licensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 34

Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 34

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . Page 35

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . Page 36

OPERATING INSTRUCTIONS OPUS 910

Thank you for selecting the Opus 910 wireless system. Please take some time to read carefully

through this manual before setting up the equipment.

Important:

• When you unpack the product, inspect it for transport damage. If you do find transport damage,

notify the transportation company without delay. Delay in reporting transport damage could result

in the loss of your rights to compensation.

Receiver

• READ these instructions.

• KEEP these instructions.

• HEED all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with a dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus

(including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarised or grounding-type plug. A polarised plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

• Only use attachements/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with

the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to

avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

• The equipment must be set up so that the mains switch, mains plug and all connection on the rear

of the device are easily accessible.

• The equipment must be connected to a mains socket that has an earth contact.

• Never expose the equipment to rain or a high level of humidity. For this reason do not install it in

the immediate vicinity of swimming pools, showers, damp basement rooms or other areas with

unusually high atmospheric humidity.

• Do not use the device/s outside. WARNING: To reduce the risk of fire or electric shock, do not

expose this/these device/s to rain or moisture.

• Never place objects containing liquid (e.g. vases or drinking glasses) on the equipment. Liquids in

the equipment could cause a short circuit.

• Lay all connection cables so that they do not present a trip hazard.

• Check whether the connection figures comply with the existing mains supply. Serious damage

could occur due to connecting the system to the wrong power supply. An incorrect mains voltage

could damage the equipment or cause an electric shock.

Important Safety Instructions

Transmitter

• Protect the transmitter from moisture and sudden impacts. You could either injure yourself or others

or damage the transmitter.

• Do not blow into the microphone. In a condenser microphone this could damage the transformer.

It is preferable to carry out a speech trial.

• Clip-on microphones are often very compact. If they are accidentally swallowed there is a risk of

choking. Always keep this type of microphone away from small children.

• Always switch off the transmitter before charging or changing the battery.

• If the transmitter is fitted with a normal battery, never charge it in the charging unit. The transmitter

or the batteries could be destroyed. There is a risk of explosion.

• The normal commercial 9 V alkaline batteries can have a length tolerance of 2 - 3 mm. When

changing the battery always ensure good contact.

• From time to time the battery contacts should be cleaned with a soft cloth moistened with spirits

or alcohol.

• If the transmitter is not being used for weeks or months, please remove the batteries. Batteries can

leak when not being used for a long time and corrode the conductor strips and components.

Repair is not then possible. In this case all warranty claims are null and void. The description “leak

proof” on batteries is no guarantee that they will not run out.

• Never take batteries apart yourself. The battery acid contained will damage skin and clothing.

• Do not throw used batteries into the domestic rubbish, but hand them in to local collection points.

• This equipment needs adequate ventilation. Do not cover ventilation grilles. If the heat it generates

cannot be dissipated, the equipment could be damaged or flammable materials in its immediate

vicinity could be ignited. Take care to ensure that the air can circulate freely through the ventilation

grilles and keep flammable materials away.

• Never place naked flames near the equipment.

• If the equipment causes a blown fuse or a short circuit, disconnect it from the mains and have it

checked and repaired.

• Do not open the equipment without authorisation. You could receive an electric shock. Leave all

service work to authorised expert personnel.

• Do not hold the mains cable with wet hands. There must be no water or dust on the contact pins.

In both cases you could receive an electric shock.

• The mains cable must be firmly connected. If it is loose there is a fire hazard.

• Always pull out the mains cable from the mains and/or from the equipment by the plug - never by

the cable. The cable could be damaged and cause an electric shock or fire.

• If the power cable is connected, avoid contact of the unit with other metallic objects.

• Do not insert objects into the ventilation grilles or other openings. You could damage the

equipment and/or injure yourself.

• Do not use the equipment if the mains plug is damaged.

• When installing the device into a 19" rack, make sure that the mains switch, mains plug and all

connection on the rear of the device are easily accessible.

• When connecting a headphone, please make sure that the volume is turned down to minimum.

Adjust the volume after putting on the headphone. Do not set the volume too high, as you could

permanently damage your hearing.

FCC Regulation

FCC ID: OSDTS910 for TS 910 M, TS 910 C

OSDS910M for S 910 M

OSDS910C for S 910 C

Canada IC: 3628A-S910M for S 910 M

3628A-S910C for S 910 C

3628A-TS910 for TS 910 M, TS 910 C

3628A-NE91X for NE 911

3628A-NE91X for NE 912

3628A-NE91X for NE 914

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

NOTICE:

Changes or modifications made to this equipment not expressly approved by

beyerdynamic GmbH & Co. KG may void the FCC authorization to operate this equipment.

NOTICE:

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

NOTICE:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

For USA:

OPERATION OF WIRELESS MICROPHONES IN THE 700 MHZ BAND IS PROHIBITED AFTER

JUNE 12, 2010.

CONSUMER ALERT

Most users do not need a license to operate this wireless microphone system. Nevertheless, operating

this microphone system without a license is subject to certain restrictions: the system may not cause

harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has

no protection from interference received from any other device.

Purchasers should also be aware that FCC is currently evaluating use of wireless microphone systems,

and these rules are subject to change.

For more information, call the FCC at 1-888-CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCC´s wire-

less microphone website at www.fcc.gov/cgb/wirelessmicrophones.

1. NE 911 / 912 / 914 Diversity Receiver

1.1 Controls and Indicators

NE 911 front view

Power switch with LED indicator

Headphone input

Volume control for headphone input to listen to individual receiving channels

NE 912 / 914: Press the volume control to select the receiving channel

Display

ACT button

Scan button

Menu control (for selecting different settings)

ESC button

Antenna connection when connecting the antennae on the front

NE 912 front view

NE 914 front view

1 2 5 4 6 7 8

1 2 5 4 6 7 8 99

1 2 5 4 6 7 8 9

Antenna input B. TNC socket. With power supply for antenna amplifier.

AF output, 3-pin XLR, balanced

Remote connection IN / OUT

Antenna input A. TNC socket. With power supply for antenna amplifier.

Mains

NE 911 only: AF output, 1/4" (6.35 mm) jack, unbalanced

NE 912 rear view

NE 911 rear view

NE 914 rear view

10 11 15 12 14 13

10 11 11 12 1413

10 11 11 11 11 12 1413

1.2 How to connect the Antennae

Connect the antennae to the TNC sockets and ( . Set them at an angle (60°).

Please note that for diversity operation both antennae have to be connected. A weighting circuit

silently switches the signal with the better S/N ratio to the output.

1.4 LC-Display and Menu Settings

On the LC-Display all operating parameters such as RF and AF level will be shown. Using the “Menu“

control you can select from 6 options. The selected function is surrounded by a square frame and

shown at the bottom of the LC-Display.

By selecting the ESC button you can cancel the current entry into the menu to display the

previous setting.

To select the individual receiving channels of the NE 912 / 914 for entering the menu settings, press

the menu control until the green LED between the ACT and the SCAN button is flashing. Turn the

menu control to select the receiving channel. The green LED of the selected receiving channel will

flash. Press the menu control to confirm. The green LED will illuminate permanently.

The functions and operation are described in the following.

1.3 Setting up

1. Place the diversity receiver in the same room or area as the transmitters. Make sure the diversity

receiver is placed as close as possible to the transmitter.

2. Do not place the diversity receiver near digitally controlled equipment.

3. Connect the AF-output to the corresponding input of the mixing console or amplifier.

4. Connect the receiver to AC power.

5. Switch on the receiver . The red LED will illuminate.

6. If you use the receiver on a tabletop, please stick the supplied rubber pads to the bottom of the

receiver to ensure a sufficient ventilation.

1310

1.4.1 Diversity indication of the Receiving Channel

Each receiving module has two separate receiving circuits, one for each antenna. The signal with the

better S/N ratio is switched to the output. The received diversity channel is shown in the LC-display.

Otros manuales para Opus 910

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de micrófono de Beyerdynamic

Beyerdynamic

Beyerdynamic Opus 500 Manual de usuario

Beyerdynamic

Beyerdynamic STEGOS Manual de usuario

Beyerdynamic

Beyerdynamic UHF Wireless System Opus 900 Manual de usuario

Beyerdynamic

Beyerdynamic Opus 100 Manual de usuario

Beyerdynamic

Beyerdynamic TG 100 Beltpack Set Manual de usuario

Beyerdynamic

Beyerdynamic STEGOS Guía de configuración

Beyerdynamic

Beyerdynamic TG 1000 Manual de usuario

Beyerdynamic

Beyerdynamic TG 1000 Manual de usuario

Beyerdynamic

Beyerdynamic Synexis Manual de usuario

Beyerdynamic

Beyerdynamic Opus 600 Manual de usuario

Beyerdynamic

Beyerdynamic STEGOS Manual de usuario

Beyerdynamic

Beyerdynamic TG 500 Manual de usuario

Beyerdynamic

Beyerdynamic Opus 910 Manual de usuario

Beyerdynamic

Beyerdynamic Opus 600 Manual de usuario

Beyerdynamic

Beyerdynamic TG 500 Instrucciones de funcionamiento y mantenimiento

Beyerdynamic

Beyerdynamic UHF Wireless System Opus 900 Manual de usuario

Beyerdynamic

Beyerdynamic SIS Manual de usuario

Beyerdynamic

Beyerdynamic TG 100 Beltpack Set Manual de usuario

Beyerdynamic

Beyerdynamic TG 100 Beltpack Set Manual de usuario

Beyerdynamic

Beyerdynamic TG 1000 Manual de usuario

Beyerdynamic

Beyerdynamic TG 1000 Manual de usuario

Beyerdynamic

Beyerdynamic Opus 600 Manual de usuario

Manuales populares de Sistema de micrófono de otras marcas

Paso

Paso R824 Manual de usuario

Naxa

Naxa NAM-982 Manual de usuario

Motorola

Motorola PMNN4461 Manual de usuario

Xvive

Xvive U3 Manual de usuario

Tekon

Tekon DUOS Manual de usuario

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manual de usuario

Devine

Devine WMD-IE Manual de usuario

LG LF-D7150 Manual de usuario

GE S768DAV Manual de usuario

LD U305 HBH 2 Manual de usuario

Chainway

Chainway URA8 Manual de usuario

ORATOR

ORATOR D860TD Manual de usuario

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manual de usuario

Alpha Technologies

Alpha Technologies RBMS Manual de usuario

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manual de usuario

Shure

Shure UA844 Manual de usuario

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manual de usuario

Pyle

Pyle PDWM5000 Manual de usuario