BESTEK FEB-1251 Manual de usuario

Fanless System

FEB-1251

Always at the forefront of innovation

User Manual

This publication contains information that is protected by copyright. No part of it may be reproduced in any

form or by any means or used to make any transformation adaptation without the prior written permission

from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no representations or

warranties with respect to the contents or use of this manual and specifically disclaims any express or implied

warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the

use or the results of the use of this document. Further, the manufacturer reserves the right to revise this

publication and make changes to its contents at any time, without obligation to notify any person or entity of

such revisions or changes.

All trademarks and registered trademarks of products appearing in this manual are the properties of their

respective holders.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

Trademarks

FCC and DOC Statement on Class A

1. Warranty does not cover damages or failures that are raised from misuse of the product, inability to use the

product, unauthorized replacement or alteration of components and product specifications.

2. The warranty is void if the product has been subject to physical abuse, improper installation, modification,

accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to

perform service, adjustments or repairs on the product, whether in or out of warranty. It must be returned

to the purchase point, factory or authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequential damages to the product that has

been modified or altered.

It is quite easy to inadvertently damage your PC, system board, components or devices even before installing

them in your system unit. Static electrical discharge can damage computer components without causing any

signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are ready to install

it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or connectors by their

ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other

components. Perform the upgrade instruction procedures described at an ESD

workstation only. If such a station is not available, you can provide some ESD protection

by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis.

If a wrist strap is unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Warranty

Static Electricity Precautions

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation

or servicing, cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by the manufacturer.

• Dispose of used batteries according to local ordinance.

Before using the system, prepare basic system components.

If the system comes as a barebone; that is, none of the key components, including processor, memory, and hard

drive has been pre-installed as part of your purchase, you will need to at least ensure a compatible counterpart

is located and installed.

You will also need a few external system peripherals intended for the use of the system, a common pool with

at least a keyboard, a mouse, and a monitor is thus suggested.

Safety Measures

Before Using the

System

Table of Content

Copyright ....................................................................................................................................................................

Trademarks ....................................................................................................................................................................

FCC and DOC Statement On Class A.............................................................................................................................. 2

Warranty ........................................................................................................................................................................ 3

Static Electricity Precautions......................................................................................................................................... 3

Safety Measures ............................................................................................................................................................ 4

Before Using the System Board..................................................................................................................................... 4

Table of Content ............................................................................................................................................................ 5

Chapter 1 General Information

1.1 Main

Feature ........................................................................................................................................................... 7

1.2

Specifications .......................................................................................................................................................

1.3 System Layout ................................................................................................................................................... 9

1.4 Indicators and Features .................................................................................................................................. 10

Chapter 2 Preparation

2.1 Before You Begin...................................................................................................................................... 13

2.2

Precautions.........................................................................................................................................................

2.3 Open Up Bottom Cover

......................................................................................................................................

2.4 Accessing Memory............................................................................................................................................. 15

2.5 Accessing 2.5” Drive......................................................................................................................................... 16

2.6 Accessing CFast Card ...................................................................................................................................... 17

2.7 Installing Wireless Module & Antenna........................................................................................................... 18

2.8 Accessing SIM Card......................................................................................................................................... 20

2.9 Installing SATADOM ........................................................................................................................................ 21

Chapter 3 Operation

3.1 Turning On The System.................................................................................................................................... 23

3.2 Installing

Operating System & Drivers ........................................................................................................

3.3 Understanding LED Indicators ........................................................................................................................ 25

Chapter 4 BIOS Setup

4.1 Entering Setup ................................................................................................................................................ 28

4.2 Getting Help.................................................................................................................................................... 28

4.3 Control Keys .................................................................................................................................................... 28

4.4 The Main Menu............................................................................................................................................... 29

4.5 The Advanced Menu........................................................................................................................................ 30

4.6 The Chipset Menu..................................................................................................................................................... 32

4.7 The Boot Menu................................................................................................................................................ 34

4.8 The Security Menu .......................................................................................................................................... 35

4.9 The Save & Exit Menu...................................................................................................................................... 36

Chapter 5 Auxiliary Information

5.1 GPIO Programming Guide .............................................................................................................................. 39

5.2 WDT Programming Guide............................................................................................................................... 40

Chapter 1

General Information

Processor Performance

FEB-1251 is a fanless embedded wall mount system that is pre-installed with Intel® Cedarview D2550 Dual-

Core 1.86GHz processor bundled with integrated graphic and one SO-DIMM slot supporting up to maximum

4GB DDR3-800/1066.

All-In-One & Compact Design

The system boasts a considerably compact size of just 185x131x54mm, with one DVI-I, one HDMI, dual

gigabit RJ45 network, four COM ports, six USB 2.0, and one CFast, all available on the built-in embedded

board therein the TCO (Total Cost of Ownership) can be minimized. The provision of wide range DC power

input and the true fanless feature has made the system a perfect controller for FA and MA, where a variety

of different power sources, such as 12/19/24Vdc, are available.

List of Key Features

Onboard Intel® Atom™ D2550

1x HDMI + 1x DVI-I Output

Dual Intel® Gigabit LAN Ports

2x RS-232, 2x RS-232/422/485

6x USB 2.0 Ports

1x External CFast Socket

1x miniPCIe Slot

Two Antenna Outlets

10~28Vdc Wide Range Power Input

1.1 Main Feature

Construction

Form Factor

Proprietary Wall Mount Chassis

Material

Aluminum

Dimension (W x D x H)

185 (W) x 131 (D) x 54 (H) mm

Color

Silver & Red

Certification

CE/FCC

System

Processor

Intel® Atom™Cedarview D2550 Dual-Core Processor

Memory

1x DDR3 SO-DIMM Slot up to 4GB

Power

12~28Vdc / Optional 12Vdc Power Adaptor

Drive Bays

SATA HDD

1 (2.5”)

CFast

1x External Accessible

Cooling

True Fanless Design via Aluminum Housing

Connectivity

Communication

Dual Intel® 82574L PCIe GbE, Support WOL & PXE

Front I/O

1x ATX Power Switch, 1x Power LED, 1x HDD LED

4 x COM Ports (Two RS232/422/485)

2x USB 2.0 Ports, 2x Audio Jacks, 2x Antenna Outlets

Rear I/O

2x RJ45 LAN Ports, 4 x USB 2.0 Ports

1x HDMI + 1x DVI-I (Support VGA via Cable)

1x 2-pin Power Input, Support +10~28Vdc

1x External Screwed Type CFast Socket

Expansion Slots

Rear Access

1x miniPCIe Slots for Half-sized and Full-sized Adaptor

Environment

Operating Temperature

-5 ~ 55oC

Storage Temperature

-20 ~ 80oC

Operating Humidity

0% ~ 90%

Storage Humidity

0% ~ 90%

Shock Protection

HDD (20G), CFast (50G)

Vibration Protection

Random (0.5Grms), Sinusoidal (0.5Grms)

1.2 Specifications

Figure 1.1: System Layout of FEB-1251

1.3 System Layout

►Front View

1. DB9 RS-232

2. DB9 RS-232/422/485

3. DB9 RS-232/422/485

4. DB9 RS-232

5. Power Switch

6. Antenna Cut-Out

7. Power LED (Green) + HDD LED (Yellow)

8. Microphone Jack

9. Line-Out Jack

10. 1* USB 2.0

11. 1* USB 2.0

12. Antenna Cut-Out

1.4 Indicators & Features

Tabla de contenidos

Otros manuales de De oficina de BESTEK

BESTEK

BESTEK MEB-7601 Manual de usuario

BESTEK

BESTEK MEB-7601 Manual de usuario

BESTEK

BESTEK MEB-7400D Manual de usuario

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario