Page 3 of 8
User Manual: HACCP SmartStep
™ Footwear Sanizing System | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Best Sanizers, Inc. I 888.225.3267 I www.bestsanizers.com
Installaon Instrucons:
For ADB0002 Unit:
1. Posion footwear sanizing unit in desired locaon.
2. Place Alpet® D2 Surface Sanizer pail in close proximity to
sanizing unit. Sucon hose length should not exceed 8
. (2.4 m). Remove white shipping cap from pail, replace
with red safety adapter cap (USP20028) and sucon line
(see page 7 for diagram). The HACCP SmartStep’s sucon
tube is now connected to the pail’s internal dip tube.
3. Connect an air line to the air ng (AP25).
4. Prime the unit according to the Priming Instrucons.
For ADB0002-MH Unit:
1. Posion footwear sanizing unit in desired locaon.
2. Aach handle to handle bracket with bolts on the ends
(B5161834). Secure with set screws (B5161858 and
LNSS516).
3. Mount handle assembly to oor or wall (hardware not
included).
4. Li up on the front of the grate and rotate the top half
of the unit to release from the base. Slide top half of unit
from the bracket (FS-GUARD).
5. Hook the plate (FS-FMP) on the underside of the collecon
basin to the bracket at the base of the mounng handle.
6. Place Alpet® D2 Surface Sanizer pail in close proximity to
sanizing unit. Sucon hose length should not exceed 8
. (2.4 m). Remove white shipping cap from pail, replace
with red safety adapter cap (USP20028) and sucon line
to pail.
7. Connect an air line to the air ng (AP25). Prime the unit
according to the Priming Instrucons.
For ADB0002-BS Unit:
1. Posion footwear sanizing unit in desired locaon.
2. Aach handle to boot scrubber base with bolts on the
ends (B5161812). Secure with set screws (B5161834 and
LNSS516).
3. Slide debris tray (DBTR) under boot scrubber, li up and
hook tray into slots on the front of the boot scrubber
frame to secure.
4. Connect debris shield (DBSH) by sliding hooks into the
slots on the back of the boot scrubber frame. Note:
Brushes (USP20032 and USP20033) must be removed
before installing/uninstalling debris shield.
5. Conrm that boot scrubber is in desired locaon and
mount to oor (hardware not included).
6. Posion mounng bracket (FS-BPL) for footwear sanizer
next to the boot scrubber and secure to the oor
(hardware not included).
7. Hook the plate (FS-FMP) on the underside of the collecon
basin to the bracket at the base of the mounng handle.
8. Place Alpet® D2 Surface Sanizer pail in close proximity to
sanizing unit. Sucon hose length should not exceed 8
. (2.4 m). Remove white shipping cap from pail, replace
with red safety adapter cap (USP20028) and sucon line.
9. Connect an air line to the air ng (AP25).
10. Prime the unit according to the Priming Instrucons.
For USP20031 Unit:
1. Posion boot scrubber unit in desired locaon.
2. Aach handle to boot scrubber base with bolts on the
ends (B5161812). Secure with set screws (B5161834 and
LNSS516).
3. Slide debris tray (DBTR) under boot scrubber, li up and
hook tray into slots on the front of the boot scrubber
frame to secure.
4. Connect debris shield (DBSH) by sliding hooks into the
slots on the back the boot scrubber frame. Note: Brushes
(USP20032 and USP20033) must be removed before
installing/uninstalling debris shield.
5. Conrm that boot scrubber is in desired locaon and
mount to oor (hardware not included).
6. Posion mounng bracket (FS-BPL) for footwear sanizer
next to the boot scrubber and secure to the oor
(hardware not included).
7. Hook the plate (FS-FMP) on the underside of the collecon
basin to the mounng bracket (FS-BPL).
Priming Instrucons:
Note: This unit is for use with fully protecve footwear only. Do not
acvate the unit if a user’s foot is not posioned inside the spray
guard (SS2-SH).
1. Verify that the Alpet® D2 Surface Sanizer pail is full. Check all
external tubing connecons and verify that none are loose or
leaking.
2. Place foot on the grate (FS-GRATE) and step down with heel
10-15 mes or unl all air has been purged from the sucon
line.
3. Check boom of footwear for proper sanizer applicaon. The
enre sole should be covered with a consistent spray paern.
