BEST ACCESS SYSTEMS 45HM IDH Max Mortise Lock Manual de usuario

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc

The 45HM IDH Max® Mortise Lock provides the following

features in an integrated lock, eliminating the need to

install separate sensors in and around the door frame:

■electrified locking mechanism

■electronic token reader

■integrated trim

■door status detection

■latchbolt status detection

■ability to exit without triggering an alarm (RQE)

■compatibility with varied access control panels/

reader interfaces.

Note:

For a list of compatible access control panels/

reader interfaces, contact your local BEST

representative.

A panel interface module is provided with the lock. The

panel interface module receives token data and lock

sensor data from the lock through an RS-485 connection.

It translates this data into parallel signals, which it sends

to the access control panel/reader interface. The panel

interface module also translates control signals received

from the access control panel/reader interface and sends

them to the lock. The figure below shows the relationship

between the components in the IDH Max® system.

Installation Instructions for

45HM IDH Max® Mortise Locks

Power

supply

Lock

Wire

transfer

hinge

Field wire

harness

Power (2)

RS-485 Communication (2)

Communication tamper or

Latchbolt status (2)

Door & latchbolt status or

Door status (2)

RQE status (2)

Strike (2)

Token data (2)

Reader LED (2)

Sounder (2)

Card present (1)

Panel interface

module

Access

control

panel/

reader

interface

Power (2)

Power

supply

For hole sizes, see the

W28 Template

(T81625)

Figure 1 Identifying holes to drill

Installation Instructions for 45HM IDH Max® Mortise Locks

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc.

2Align templates

Note:

If the door is a fabricated hollow metal door,

determine whether it is properly reinforced to support

the lock. If door reinforcement is not adequate, consult

the door manufacturer for information on proper

reinforcement. For dimensions for preparing metal

doors, see the

W29 Template –

Installation

Specifications for 45HM IDH Max Mortise Locks

(T81630)

1 Separate the four templates provided on the

W28

Template—Installation Template for 45HM IDH Max

Mortise Locks

(T81625).

2 Position one of the door edge templates on the door,

making sure that the lock case mortise shown on the

template aligns with the mortise pocket prepared in

the door.

3 Using the centerlines on the door edge template as a

guide, position the appropriate door template on each

side of the door. You need to take the bevel into

account. Tape the templates to the door.

Figure 1 Aligning the templates

Installation

template

Door edge

template

Centerline

1Identify holes to drill

1 Determine the lock function to be

installed.

2 Determine the inside and outside, hand,

and bevel of the door.

3 See the

Holes by Function

table and

Figure 1 to determine the holes to be

drilled for the lock function.

Functions

Holes by Function

DEU/DEL LEU/LEL NXEU/NXEL TDEU/TDEL

Holes to drill I/S O/S I/S O/S I/S O/S I/S O/S

AForged trim

(2 holes)†

† Because these holes pass through the mortise pocket, it is recommended that each

hole be drilled separately rather than straight through.

Through

door

Through

door

Through

door

Through

door

BHarness†Through

door

Through

door

Through

door

CStandard cylinder ■■

DSensor & solenoid wire ■■■■

FThumb turn ■ ■

GTrim mounting

(2 holes)†Through

door

Through

door

Through

door

Through

door

HLever†Through

door

Through

door

Through

door

Through

door

Installation Instructions for 45HM IDH Max® Mortise Locks

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc.

Installation Instructions for 45HM IDH Max® Mortise Locks

3Drill wire channel through door

Caution 1:

Check with your local fire marshal

before drilling a fire-rated door. Drilling through

a fire-rated door may void the fire label.

Caution 2:

Be careful to drill straight through the

door, making sure the drill does not break

through the face of the door.

1 Remove the hinge nearest the mortise cavity.

2 Using a 3 to 4 foot drill bit, drill a 3/8″diameter

channel through the upper back of the mortise cavity

to the center of the nearest hinge mortise.

See Figure 3.

Note:

It may be easier to drill halfway from each side

of the door.

4Optional: Prepare door for door status

switch

(for deadbolt function locks with

door sensing only)

1 Locate the centerpoint for the door status switch 2.5″

above the top of the faceplate mortise on the edge of

the door (as shown in Figure 4).

2 Drill a 1″diameter hole 1 3/4″deep for the door

status switch.

3 Position the drill so the tip of the bit is approximately

1″into the hole and the bit is close to the top edge of

the hole. Then drill a 3/8″channel at approximately a

35° angle from the door status switch hole into the

mortise cavity (as shown in Figure 4).

Figure 3 Drilling the wire channel through the door

Hinge mortise

Figure 4 Preparing for the door status switch

Door status

switch hole 3/8″

channel

Installation Instructions for 45HM IDH Max® Mortise Locks

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc.

5Determine wire gauge for power

wiring

1 Calculate the total length of the power wire run

by summing:

■The distance from the power supply to the first

door.

■If powering more than one door daisy-chained to

the same power supply, add the total distance of

the power runs between the doors.

2 Refer to the table below to determine the minimum

wire gauge based on the number of doors sharing the

power supply and the total length of the wire run.

6Prepare door for wire transfer hinge

and run field wiring

1 Drill a wire access hole through the frame side of the

hinge mortise where you removed the hinge in Task 3,

Step 1 on page 3.

2 Drill holes (or pockets) for splice connectors in the

frame and door. Refer to the hinge manufacturer’s

specifications for the hole location.

3 De-burr the holes to prevent damage to the hinge

leads.

4 Run the power field wiring from the location for the

lock’s power supply to the location for the wire

transfer hinge.

Note 1:

To match the lock’s wire color, use yellow for

12 volts DC power.

Note 2:

To minimize lever temperature, install an

8WTCM (temperature control module) in series with

the power and ground wiring within 20 feet of the

lock. Use only one 8WTCM per lock. This module is

supplied with electrically locked (EL) functions and is

optional with electrically unlocked (EU) functions.

– Continued

1 door 2 doors 3 doors 4 doors Min. wire gauge

250 ft. 125 ft. 75 ft. 60 ft. 18 AWG

400 ft. 200 ft. 130 ft. 100 ft. 16 AWG

600 ft. 300 ft. 185 ft. 150 ft. 14 AWG

Figure 6 Running field wiring

Door frame Door

Field wiring

Installation Instructions for 45HM IDH Max® Mortise Locks

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc.

Installation Instructions for 45HM IDH Max® Mortise Locks

Configuring & installing the mortise case

5 Run the sensor wiring from the location of the access

control panel to the location for the wire transfer

hinge.

To match the sensor wire colors, refer to the table

below.

7 Pull the field wiring down the wall and through the

access hole in the frame.

7Optional: Install door status switch

(for deadbolt function locks with door

sensing only)

1 Position the shield on the door status switch with the

notch facing downwards (towards the mortise

pocket).

Caution:

Make sure the wires are not routed across

any sharp edges or over any surface that could

damage its sleeving.

2 Feed the wires for the door status switch into the door

status switch hole and through the channel into the

mortise cavity.

3 Insert the door status switch assembly into the door

status switch hole.

8Rotate latchbolt

(if necessary)

Note:

If a function specific mortise case was ordered,

some steps for configuring the case have already been

performed at the factory.

1 Determine whether you need to rotate the latchbolt to

match the handing of the door.

Note:

The angled surface of the latchbolt must contact

the strike when the door closes.

2 If you need to rotate the latchbolt, insert a flat blade

screwdriver into the latch access point approximately

Wire connection Color No. of wires

Door status sensor White 2

Latchbolt status sensor Purple 2

RQE status sensor Brown & Orange 2

Figure 7 Installing the door status switch

Door

status

switch

Shield

Figure 8 Rotating the latchbolt

Latch access point

Installation Instructions for 45HM IDH Max® Mortise Locks

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc.

Configuring & installing the mortise case

1/2″into the case and press to extend the latch out of

the case. See Figure 8.

3 Rotate the latchbolt 180 degrees and allow it to retract

into the case.

9Position hub toggles

(if necessary)

1 Check whether the hub toggles are in the proper

position for the lock. See the table below and Figure 9.

Note 1:

For LH & LHRB doors, the inside is the back

side of the case and the outside is the cover side of the

case.

For RH & RHRB doors, the inside is the cover side of the

case and the outside is the back side of the case. The

cover is mounted to the case with four screws.

Note 2:

If the lock has an optional RQE status sensor,

two RQE status switches are installed in the mortise

case. However, only the switch for the inside of the

lock needs to be connected. Before you install the

mortise case in the door, determine whether you need

to connect the ‘Case Side’ pair of RQE wires or the

‘Cover Side’ pair of RQE wires, based on the handing of

the door.

2 To change the position of a hub toggle, remove the

toggle screw, move the toggle into the desired

position, and re-tighten the screw.

10 Install mortise case

1 Remove the faceplate from the mortise case, if

necessary.

2 Insert the mortise case into the mortise cavity, while

feeding the sensor and solenoid wires into the mortise

cavity and out the sensor & solenoid wire hole to the

inside of the door.

Hub toggle positions

Function Hub toggle positions

DEU/DEL, LEU/LEL, NXEU/

NXEL, TDEU/TDEL

Inside down (always unlocked) &

outside up (lockable)

Figure 9 Positioning hub toggles

Hub toggleHub toggle

Figure 10 Installing the mortise case (inside of door)

Field wire harness

Sensor & solenoid

wire hole and wires

Inside of door

Mortise

case

Fire plate

Installation Instructions for 45HM IDH Max® Mortise Locks

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc.

Installation Instructions for 45HM IDH Max® Mortise Locks

Installing the trim

Note 1:

The armored front of the mortise case self-

adjusts to the door bevel.

Note 2:

The field wire harness should be routed above

and behind the mortise case (depending on where the

hole through the door meets the mortise cavity).

3 Make sure there are 3″to 4″of slack in the field wire

harness to allow access to the control electronics

circuit board located in the fire plate.

3 Secure the mortise case with the case mounting

screws.

11 Install trim mounting plates

1 Insert the outside trim mounting plate through the

door and mortise case.

2 Position the inside trim mounting plate opposite the

outside trim mounting plate and screw them securely

in place.

Caution:

Do not overtighten the trim mounting

plate screws. Overtightening may damage the

locking mechanism.

12 Install concealed cylinder & core

(DEU/DEL and TDEU/TDEL functions

only)

1 Use a cylinder wrench to thread the cylinder into the

mortise case so that the groove around the cylinder is

even with the door surface as shown in Figure 12.

Caution:

A malfunction can occur if the cylinder is

threaded in too far.

2 Secure the cylinder in the mortise case with the

cylinder retainer screw.

3 Insert the control key into the core and rotate the key

15 degrees to the right.

4 With the control key in the core, insert the core into

the cylinder.

Figure 11 Installing the trim mounting plates

Outside

mounting

plate

Inside

mounting

plate

Figure 12 Installing the concealed cylinder

Cylinder

retainer

screw

Installation Instructions for 45HM IDH Max® Mortise Locks

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc.

Installing the trim

5 Rotate the control key 15 degrees to the left and

withdraw the key.

6 The control key can be used to remove cores and

to access doors. Provide adequate security for the

control key.

13 Install trim hole insert and bushing

1 Insert the trim hole insert into the upper trim hole on

the outside of the door, as shown in Figure 13.

2 Insert the bushing into the field harness & reader wire

hole on the outside of the door, as shown in

Figure 13.

Note:

You do not need to change the positions of the

DIP switches on the control electronics circuit board

located in the inside escutcheon.

■By default, switches 1 through 5 are set to ON.

These switches are for possible future applications.

■By default, switches 6 and 7 are set to ON for

automatic baud rate detection. This setting lets you

determine the baud rate for communication

between the lock’s control electronics circuit board

and the panel interface module by setting DIP

switches on the panel interface circuit board. (See

page 19.)

■Switch 8 is set to OFF for locks with a swipe-type

magnetic stripe card reader, a proximity reader, or

a keypad reader; it is set to ON only for locks with

an insertion-type magnetic stripe card reader.

Figure 13 Installing the trim hole insert and bushing

Trim hole

insert

Bushing

Outside of door

Installation Instructions for 45HM IDH Max® Mortise Locks

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc.

Installation Instructions for 45HM IDH Max® Mortise Locks

Installing the trim

14 Connect reader wire harness

1 From the outside of the door, feed the reader wire

harness connector through the field harness & reader

wire hole.

2 Temporarily rest the outside trim on the door by

inserting the trim studs into the stud holes.

15 Install fire plate

1 From the inside of the door, feed the wiring through

the fire plate harness hole.

2 Position the fire plate on the door so that the inside

mounting plate fits through the square opening in the

fire plate.

3 Insert the two counter sunk mounting screws into the

holes at the top and bottom of the fire plate.

Note:

You may have to push the PCB board up out of

the way of the mounting holes to access them.

4 Tighten the mounting screws until the fire plate is

securely mounted to the door.

Caution 1:

When routing the reader wire harness,

make sure the reader wire harness is not routed

across any sharp edges or over any surface that

could damage its sleeving or wire insulation.

Figure 14a Feeding the reader wire harness connector

from the outside trim through the door

Reader wire

harness connector

Field harness &

reader wire hole

Outside trim

Outside of door

Figure 15 Installing the fire plate and connecting the

reader wire harness

Inside of door

Reader wire

harness

connector

Control elec-

tronics cir-

cuit board

Mounting

screw

Mounting

screw

Installation Instructions for 45HM IDH Max® Mortise Locks

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc.

Completing the installation at the door

16 Secure through-bolt trim and

complete connections

Caution:

When routing the solenoid and sensor

wire harness, the sensor wires, and the solenoid

wires, make sure the wires are not routed across

any sharp edges or over any surface that could

damage their sleeving or wire insulation.

1 Make the solenoid connection and three sensor

connections, and place the wires into the inside trim.

Caution:

When making the sensor connections

and solenoid connection, make sure:

■there are no loose wire connections where the

wires are inserted into the connectors

■the connectors are firmly mated.

17 Install bottom cover

(inside escutcheon)

1 Position the battery wires above the side tabs and

against the side of the fire plate, as shown in

Figure 16.

2 Optional for Thumb Turn option only: Make sure

that the Thumb Turn is in the upright position, as

shown in Figure 16.

3 Use two cover screws to secure the cover to the side of

the fire plate.

Note:

Phillips Type 2 and T20 Torx options are

available for the cover mounting screws.

Caution:

Dress all wires away from possible pinch

points before the bottom cover is put in place.

Wire connection Color No. of

wires

No. of

pins

Solenoid Yellow 2 3

RQE Brn/Org 2 3

Shorting connection Purple 2 2

Door status sensor White 2 2

Figure 16 Installing the bottom cover

Inside of door

Bottom

cover

Cover

screws

Thumb turn

(optional)

Side tabs

Otros manuales para 45HM IDH Max Mortise Lock

Tabla de contenidos

Otros manuales de Cerradura de puerta de BEST ACCESS SYSTEMS

BEST ACCESS SYSTEMS

BEST ACCESS SYSTEMS 45HM IDH Max 1300 Manual de usuario

BEST ACCESS SYSTEMS

BEST ACCESS SYSTEMS 45HG Manual de usuario

BEST ACCESS SYSTEMS

BEST ACCESS SYSTEMS B.A.S.I.S. V Manual de usuario

BEST ACCESS SYSTEMS

BEST ACCESS SYSTEMS 34HW Manual de usuario

BEST ACCESS SYSTEMS

BEST ACCESS SYSTEMS V Series Manual de usuario

BEST ACCESS SYSTEMS

BEST ACCESS SYSTEMS 45HM IDH Max Mortise Lock Manual de usuario

BEST ACCESS SYSTEMS

BEST ACCESS SYSTEMS W Series Manual de usuario

BEST ACCESS SYSTEMS

BEST ACCESS SYSTEMS B.A.S.I.S. V Manual de usuario

Manuales populares de Cerradura de puerta de otras marcas

Assa Abloy

Assa Abloy effeff 827A-IP Manual de usuario

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario