Besam PowerSwing Manual de usuario
Besam PowerSwing
Installation, Adjustment and Troubleshooting Manual
Complies with ANSI/BHMA A156.10 standard for Power Operated Pedestrian Doors and A156.19
standard for Power Assist and Low Energy Power Operated Doors. UL 325 Listed.
US23-0922-02 10-21-2002
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
PowerSwing US23-0922-022
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
Improperly adjusted doors can cause injury and equipment damage.
Inspect door operation daily using safety checklist in Owner’s Manual and at
door.
Have door adjusted as described in Owner’s Manual.
Safety devices must be in place and operational.
Have door inspected at least once a year by an AAADM inspector, and always
after any adjustment or repair.
In the following manual, the word:
Caution means that injury or property damage can result from failure to
follow instructions;
Note indicates important steps to be followed or important differences in
equipment.
Revision
At each revision all revised pages will get a new updated issue number (year-
month-day). The first leaf (pages 1 and 2) will always have the same issue num-
ber as the revised pages. Changes will be marked with a vertical line in the margin.
The table below shows the latest issue numbers.
Page Issue No. Page Issue No. Page Issue No.
01 10-21-2002
|
02 10-21-2002
|
03 10-21-2002
|
04 01-18-2001
05 01-18-2001
06 10-21-2002
|
07 01-18-2001
08 10-21-2002
|
09 01-18-2001
10 10-21-2002
|
11 10-21-2002
|
12 10-21-2002
|
13 10-21-2002
|
14 10-21-2002
|
15 10-21-2002
|
16 01-18-2001
17 10-21-2002
|
18 01-18-2001
19 10-21-2002
|
20 10-21-2002
|
21 10-21-2002
|
22 10-21-2002
|
23 10-21-2002
|
24 10-21-2002
|
25 10-21-2002
|
26 01-18-2001
27 01-18-2001
28 01-18-2001
29 01-18-2001
30 01-18-2001
31 10-21-2002
|
32 10-21-2002
|
33 01-18-2001
34 01-18-2001
35 10-21-2002
|
36 01-18-2001
37 01-18-2001
38 01-18-2001
39 01-18-2001
40 10-21-2002
|
41 01-18-2001
10-21-2002
3PowerSwing US23-0922-02
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
Contents
Revision 2
Important information 4
Introduction 5
Function description 5
Technical specifications 6
Models 7
Part Identification & Options 8-10
Mechanical installation 11-19
Installation with adapter plate 13-14
Operator with arm system PUSH 15-17
Operator with arm system PULL 18-21
Electrical connection 22-25
Control units 22
Connection of control units 23-25
Start-Up 26-31
Connection of activation units… 28
Connection of mat to extension unit EXA 29
Connection of OPD to extension unit EXA 29
Connection of Push & Go to extension unit EXA 30
Connection of Airing position to extension unit EXA 30
Connection of PassPort presence sensor 31
Cover 32
Installation on fire doors 33-38
Troubleshooting 39-40
Installation examples 41
10-21-2002
01-18-2001 PowerSwing US23-0922-024
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
Important I nformation
Important Notice!
To avoid bodily injury, material damage and malfunction of the product,
the instructions contained in this manual must be strictly observed dur-
ing installation, adjustment, repairs and service etc. Only Besam trained
experts should be allowed to carry out these operations.
Radio and Television Reception
This equipment generates and uses radio frequency energy and if not
installed and used properly, that is, in strict accordance with the manufac-
turer’s instructions, may cause interference to radio and television recep-
tion. It has been designed to comply with the emission limits in accord-
ance with EN 500811 (US market FCC Part 15) which are designed to
provide reasonable protection against such interference in a residential
installation. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Re-orient the receiving antenna.
Relocate the receiver with respect to the equipment.
Move the receiver away from the equipment.
Plug the receiver into a different outlet so that equipment and receiver are
on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/
television technician for additional suggestions.
Note!
Instructions, design, specifications and illustrations which are contained
in this manual are not binding. Rights reserved for changes without previ-
ous notice.
01-18-2001 5PowerSwing US23-0922-02
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
Introduction
This manual contains the necessary details and instructions for the installation,
maintenance and service of the Besam PowerSwing.
The Besam PowerSwing is suitable for most types of external and internal swing
doors. The operator can be mounted to walls on either side of the door for pull
or push action and is suitable for single or double doors fitted with butt hinges or
center pivots.
The motor, oil pump and hydraulic unit are combined into a compact unit mounted
alongside the control unit within the cover. The operator is connected to the door
leaf with a range of different arm systems.
Function Description
The Besam PowerSwing works electro-hydraulically. It opens with an AC-motor
that via a hydraulic unit and an arm system transmits the power to the door leaf.
The closing power is from a coil spring. The movement of the door is controlled
by limit switches and valve screws.
Opening
When an opening impulse is received by the control unit, the motor starts and
the hydraulic unit rotates the drive shaft and arm system (door) with high speed
towards open position. Before fully open position the speed is reduced to low
speed. The door stops and the motor rotation ceases when the selected door open-
ing angle is reached. This open position is kept by a hydraulic valve.
Closing
The spring closing starts when the hold open time has run out. Before fully closed
position the speed is reduced to low speed, which will be kept until the door is
completely closed. The door is kept closed by spring power. To overcome the
resistance of a striking plate a “lock kick” can be adjusted to required level.
PowerSwing US23-0922-026
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
Technical Specifications
Mains power 120 V AC ± 10 %, 60 Hz
fuse 10 A
Note!
Switch with clearly marked off-position, having a
contact separation of at least 3 (1/8'') mm in all
poles, must be incorporated in the fixed wiring.
The operator can also be plug-connected to a
wall socket.
Power consumption max. 230 W
Auxiliary voltage 13-20 V DC, 275 mA
24 V DC, 375 mA (stabilized)
Motor fuse F1 10 Amp (10 ATH)
Control fuse F2 1/2 Amp (500 mAT)
Recommended max. door weight Arm system PUSH
250 kg (550 lb) for door leaf width 1600 mm (63'')
Arm system PULL
100 kg (220 lb) for door leaf width 1400 mm
(55''). Higher door weights on request.
The PowerSwing complies with the door
weights/widths stated in the:
Controlled door closing,
EN 1154 sizes 3-6
Electrically powered hold-open device for
swing doors,
EN 1155
Coordination unit for rebated doors, EN 1158
Türschliesser mit Öffnungsautomatik
(Drechflügelantrieb)
DIN 18263-4 AU Grösse 3-6
ANSI/BHMA A156.10, A156.19
UL325/CUL325
SITAC 0166/99
Ambient temperature -30°C to +50°C (-22°F to 122°F)
Dimensions:
PowerSwing Length: 716 mm, 746-1600 mm *
(28-3/16", 29-17/32" – 63'')
PowerSwing-2 Length: 1435-3200 mm
(56 1/2" – 126")
Height: 110 mm (4-11/32")
Depth: 110 mm (4-11/32")
To be installed internally or externally with suitable weather protection.
* 716 is the European short header package.
746 allows for the operator to be mounted to the adapter plate with the addition of 2 cover
clips.
10-21-2002
01-18-2001 7PowerSwing US23-0922-02
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
Models
Two main models of the Besam PowerSwing are available:
•PowerSwing,
• PowerSwing-2, double door operators
The operators are non-handed and not dependent on the hinges. The operators suit
both pushing and pulling arm systems.
PowerSwing
The operator is offered standard in an oversize length which is field cut to required
length. Optionally length L may be specified to the factory as part of order. Pushing
arm system shown.
PowerSwing-2, double door operators
The designation PowerSwing-2 means that two operators are mounted under the
same cover to open one door each. The operator is offered standard in an oversize
length which is field cut to required length. Optionally length L may be specified
to the factory as part of order. Pushing and pulling arm system shown. It is also
possible to use two pushing or two pulling arm systems.
PowerSwing US23-0922-028
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
Part Identification & Options
1. Mounting plate
2. Motor/pump
3. Valve
4. Hydraulic unit
5. Drive shaft
6. Spring tube
7. Cable inlet
8. Main connection
9. Control unit, CSDA
10.Extension unit, EXA (option)
11.End plate
12.Programme selector,
PS3A (option)
13.Cover
14.Bearing sleeve
15.Cable holder
16.Adapter plate
17.Cover mounting clip
C Center line, drive shaft
L1
C Center line, hinge
L2
Arm system, PUSH P/N: 173 009 BK (173 883, Hybrid)
This arm systems is delivered with drive arm, telescopic part and door fitting. It is
used if the operator is installed on the wall on the opposite side of the door swing,
and approved for fire door application.
Arm system, PULL P/N: 100 125 BK
This arm system is delivered with drive arm, guide shoe and door fitting.
Arm system, PULL-P P/N: 100 134 BK
This arm system is delivered with drive arm, guide shoe door fitting, and panic
break-out.
10-21-2002
01-18-2001 9PowerSwing US23-0922-02
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
Part Identification & Options
PowerSwing US23-0922-0210
© Copyright 2006 Besam Entrance Solutions. May not be reprinted or reproduced without permission.
Part Identification & Options
10-21-2002
Otros manuales para PowerSwing
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de apertura de puertas de Besam
