Bernina 8 SERIES V29.39.00 Manual técnico

Information on Software Update

BERNINA 8 Series, V29.39.00

Information on Software Update

BERNINA 830 / 820

Software Version 3

1 General Changes 3

1.1 Language “Finnish” integrated 3

1.2 Display of data version number 3

2 Sewing Updates 4

2.1 Thread tension for the underlay segments (buttonholes) 4

2.2 Manual threading 5

2.3 The use of straight stitch feet with thread cutting 5

2.4 Disable automatic thread cutting when opening the bobbin door 5

2.5 Thread cutting without fabric movement 5

2.6 “Manual” winding of the lower bobbin thread 5

2.7 Winding indicator during sewing/embroidery 6

2.8 Reset of back stepping history 6

2.9 Thread breakage hint 7

2.10 Problem with Foot #57D and straight stitch plate compatibility 7

2.11 Presser Foot #0 can be used for automatic threading. With the “Walking foot”

automatic threading is not possible 8

2.12 Information Foot #2a corrected 8

2.13 Pattern #169 improved 9

2.14 Tension changed for the “tie on” stitches 9

2.15 Upper thread detection changed 9

3 Embroidery Updates (BERNINA 830 only) 10

3.1 Start of embroidery 10

3.2 Using zoom option with panning 10

3.3 Using Foot #44C (The new CutWork & Echo quilting foot) 10

3.4 Thread tension can be changed to a minimum of 0.5 11

3.5 Stop for manual cutting can be switched off 12

3.6 Manual “tie on” for embroidery 12

3.7 Delay of Start/Stop button reduced for embroidery 13

3.8 Thread breakage during jump stitches 13

3.9 Stitching “without thread”, shown now in embroidery mode 13

4 Important points 13

4.1 Hoop calibration 13

4.2 Feedback issues 13

4.3 Free memory 13

2/14, 04.11.2009

SOFTWARE VERSION

The Release Note V29.39.00 is in addition to the Release Note V29.21.40 (6/2009).

The newest ﬁrmware version for:

Sewing machine Firmware Embroidery module

BERNINA 830 V 29.39.00 V 1.00.10

BERNINA 820 V 29.39.00 Not available

1 GENERAL CHANGES

1.1 Language “Finnish” integrated

The following languages are now integrated: Danish, German, English, Spanish, French, Italian,

Japanese, Dutch, Russian, Swedish, Turkish and Finnish.

1.2 Display of data version number

In “Setup-Program/Information/Version”, the version of the data is visible.

Data contains all sewing and embroidery stitches.

3/14, 04.11.2009

2 SEWING UPDATES

2.1 Thread tension for the underlay segments (buttonholes)

To eliminate possible thread loops, the thread tension for segments with short step stitches is inc-

reased from 2.0 to 3.0.

2.2 Manual threading

In some cases during manual threading, the thread swing support mechanism can be blocked.

This update avoids this issue without performing any mechanical readjustments.

4/14, 04.11.2009

2.3 The use of straight stitch feet with thread cutting

The opening of the straight stitch foot is 0.4mm on both sides. The “tie on” stitch after cutting is

0.4mm to the left side. After thread cutting, the ﬁrst stitch failed resulting in the animation “need-

le will penetrate presser foot” due to the narrow tolerance in the foot opening. This has been

resolved.

2.4 Disable automatic thread cutting when opening the bobbin door

Previously the thread was cut automatically before the hook turned to the front.

To accommodate the need to change the bobbin without cutting the upper thread, the cutter is

disabled and the “lower thread empty” message appears.

2.5 Thread cutting without fabric movement

Thread cutting with the needle stop down, will NOT result in fabric movement.

2.6 “Manual” winding of the lower bobbin thread

The ﬁlling process stops at a detection of 100% ﬁll level. As a result of mechanical tolerances, it

is possible that the bobbin does not ﬁll to the maximum capacity.

5/14, 04.11.2009

In addition to the “automatic” mode, an extended manual mode is implemented.

This mode gives the user the opportunity to start and stop the winding process by

holding and releasing the winding button.

2.7 Winding indicator during sewing/embroidery

When closing the winder menu during winding, the clock symbol changes to the

winding symbol and allows switching back to the winding menu.

2.8 Reset of back stepping history

Lifting the presser foot when the needle is up automatically deletes the back stepping history in

memory.

6/14, 04.11.2009

2.9 Thread breakage hint

If the thread breaks, press the threading button to open the thread tension and remove the th-

read. Rethread the normal way.

2.10 Problem with Foot #57D and straight stitch compatibility

Select stitch #1, attach and select the foot #57D (Patchworkfoot with guide).

Open the securing function and select the straight stitch plate.

Now, it is possible to start the sewing process, without the warning message appearing:

7/14, 04.11.2009

2.11 Presser Foot #0 can be used for automatic threading. With the “Walking foot”

automatic threading is not possible

The original help text mentioned that the machine cannot be threaded automatically with foot

attached. New help text implemented:

2.12 Information Foot #2a corrected

Data correction of the dimensions of the presser foot sole.

8/14, 04.11.2009

2.13 Pattern #169 improved

Elongation limited to a maximum value of two for optimal results.

2.14 Tension changed for the “tie on” stitches

To improve the “tie on” quality with stretchy threads, such as polyester, monoﬁlament etc. the

tension setting for the ﬁrst four stitches is reduced.

2.15 Upper thread detection changed

To prevent an inaccurate warning messages from the upper thread detection, if the thread tensi-

on is detected not to be correct the machine now stops after eight stitches.

New: Before:

Max. Warning Stitches = 8 Max. Warning Stitches = 6

9/14, 04.11.2009

3 EMBROIDERY UPDATES (BERNINA 830 ONLY)

3.1 Start of embroidery

If the Start button was pressed while the bobbin door was open, either the embroidery start was

not possible or the start position was incorrect. This has been resolved.

3.2 Using zoom option with panning

When using the zoom option, only the view of the design will be moved. The hoop position rela-

tive to the design will not be changed.

3.3 Using Foot #44C (The new CutWork & Echo quilting foot)

Developed for the CutWork tool, this foot can also be used for quilting.

For designs with “cut” and “normal” embroidery layers, the foot #44C can be selected in the

stitch out mode. The outlines for the selected foot will be immediately set. The position of the

design will not change.

10/14, 04.11.2009

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de coser de Bernina

Bernina

Bernina Activa 210 Manual de usuario

Bernina

Bernina Record 930 Electronic Manual de usuario

Bernina

Bernina 900 Manual de usuario

Bernina

Bernina 820 Manual de usuario

Bernina

Bernina Record 930 Electronic Manual de usuario

Bernina

Bernina B 350 Manual de usuario

Bernina

Bernina artista 200 Embroidery Manual de usuario

Bernina

Bernina Q 24 Manual de usuario

Bernina

Bernina Bernette London 2 Manual de usuario

Bernina

Bernina L220 Manual de usuario

Bernina

Bernina Bernette 715 Manual de usuario

Bernina

Bernina Artista 180 Manual de usuario

Bernina

Bernina B 590 Guía de instalación y uso

Bernina

Bernina Sergers Manual de usuario

Bernina

Bernina 950 Industrial Manual de usuario

Bernina

Bernina 790 PRO Manual de usuario

Bernina

Bernina 540 Manual de usuario

Bernina

Bernina 700 Manual de usuario

Bernina

Bernina 435 Manual de usuario

Bernina

Bernina 950 Industrial Manual de usuario

Bernina

Bernina 740 Favorite Manual de usuario

Bernina

Bernina 570 QE Manual de usuario

Bernina

Bernina 1230 Manual de usuario

Bernina

Bernina aurora 440 QE Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario