Bend-Pak XPR-12FDL Manual de usuario

INSTALLATION AND OPERATION MANUAL

RECEIVING

The shipment should be thoroughly inspected as soon as it

is received. The signed Bill of Lading is acknowledgement

by the shipping carrier as receipt of this product as listed

in your invoice as being in a good condition of shipment. If

any of these goods listed on this Bill of Lading are missing

or damaged, do not accept goods until the shipping carrier

makes a notation on the freight bill of the missing or dam-

aged goods. Do this for your own protection.

BE SAFE

Your new lift was designed and built with safety in mind.

However, your overall safety can be increased with proper

training and thoughtful operation on the part of the operator.

DO NOT operate or repair this equipment without reading

this manual and the important safety instructions shown

inside. Keep this operation manual near the lift at all times.

Make sure that ALL USERS read and understand this

manual.

1645 Lemonwood Dr.

Santa Paula, CA. 93060, USA

Toll Free 1-800-253-2363

Tel: 1-805-933-9970

www.bendpak.com

12,000 POUND CAPACITY

SURFACE MOUNTED TWO-POST LIFTS

MODEL:

XPR-12FDL

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO

INSTALLATION AND OPERATION. BY PROCEEDING WITH LIFT

INSTALLATION AND OPERATION YOU AGREE THAT YOU FULLY

UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS

DOCUMENT. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO

OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.

Manual Revision A4 - March 2020

Manual Part Number 5900952

DRAFT

12,000 POUND CAPACITY SURFACE MOUNTED TWO-POST LIFTS

This instruction manual has been prepared especially for you.

Your new lift is the product of over 40 years of continuous research, testing and development;

it is the most technically advanced lift on the market today.

READ THIS ENTIRE MANUAL BEFORE INSTALLATION & OPERATION BEGINS.

RECORD HERE THE LIFT AND

POWER UNIT INFORMATION WHICH IS LOCATED

ON THE SERIAL NUMBER

DATA PLATES ON THE LIFT AND

ON THE POWER UNIT

Power Unit Model # _____________

Power Unit Date Of Mfg. _____________

Power Unit Serial # _____________

This information is required when

calling for parts or warranty issues.

PRODUCT WARRANTY

Our comprehensive product warranty means more than a commitment to you; it’s also a commitment to the value of your

new BendPak lift. For full warranty details and to register your new lift contact your nearest BendPak dealer or visit:

http:/ / www.bendpak.com/support/ warranty/

NOTE:

Every effort has been taken to ensure complete and accurate instructions have been included in this manual, however,

possible product updates, revisions and or changes may have occurred since this printing. BendPak Ranger reserves the right

to change specications without incurring any obligation for equipment previously or subsequently sold.

Not responsible for typographical errors.

Santa Paula, CA USA

www.bendpak.com

Model NuMber

lift CapaCity

Serial NuMber

deSCriptioN

Voltage

DANGER!

Disconnect Power

Before Servicing

WARRANTY VOID IF DATA PLATE IS REMOVED

PN 5905950

110-240VAC, 50-60 Hz, 1 Ph 380-415VAC, 50-60 Hz, 3 Ph

208-240VAC, 50-60 Hz, 1 Ph 208-440VAC, 50-60 Hz, 3 Ph

date of Mfg.

When removing the lift from shipping angles, pay close attention as the posts can slide and can cause injury. Prior

to removing the bolts make sure the posts are held securely by a fork lift or some other heavy lifting device.

PARTS INVENTORY

Be sure to take a complete inventory of parts prior to beginning installation.

Description Qty

Floorplate 1

Arm Assemblies 4

Rear Arm Assembly 2

Frame Contact Pads 4

Frame Cradle Pads 4

Off Side Column with Carriage Assembly 1

Power Side Column with Carriage Assembly 1

Hydraulic Cylinder 2

Parts Box (Packing List Enclosed) 1

Parts Bag (Packaged in Part Box) 1

Hydraulic Power Unit 1

Off Side Column

Assembly

Floorplate

Power Side

Column

Assembly

Hydraulic Power

Unit

Frame

Contact Pad

Stacking Pad

Adapters

Arm Assemblies

Frame Cradle

Pad

FLOOR PLAN

MODEL XPR-12FDL

Lifting Capacity 12,000Lbs. / 5443Kg.

*Max Capacity/ Front Axle 6,000Lbs. / 2722Kg.

*Max Capacity/ Rear Axle 6,000Lbs. / 2722Kg.

A- Height Overall: 144" / 3403mm.

B -Width Overall (Outside of Base Plate) 155" / 3937mm.

D- Cover Height 2" / 51mm.

F -Reach (Front Arm Min.): 39" / 991mm.

G -Reach (Front Arm Max.): 59" / 1499mm.

H- Reach (Rear Arm Min.): 39" / 991mm.

I- Reach (Rear Arm Max.): 59" / 1499mm.

J- Min. Pad Height: 5" / 127mm.

K- Rise: 69" / 1753mm.

L -Max Lift Height (Pad Only): 74”/1880mm

M - Max Lift Height (6" Adapter): 80” /2032mm

Motor(**) 220VAC / 60Hz.1Ph.

Time of Full Rise: 55 Seconds

Emission sound pressure at Operator Position < 70 dB(A)

* Special Voltages Available Upon Request.

The design, material and specications are subject to change without notice.

Note: Power Unit can be located at either “X” location.

CLEARANCES

XPR-12FDL

109 1

2781

22 1

571mm

136"

3453

MINIMUM

TO NEAREST

OBSTRUCTION

160 3

4082

MINIMUM

TO NEAREST

OBSTRUCTION

76mm

MINIMUM TO NEAREST BAY

OR OBSTRUCTION

152mm

MINIMUM TO NEAREST WALL

LIFT HEIGHT CLEARANCE NOTE: There must be 70” plus the height

of typical vehicle MIN distance from top of lift to nearest obstruction.

APPROACH

VALUES ARE STATED IN FOOT POUNDS (ft-lb)

SAE 0-1-2 SAE Grade 5 SAE Grade 8 SOCKET HEAD CAP SCREW

CLASS 4.8 CLASS 8.8 CLASS 10.9 CLASS 12.9

Bolt Size

(SAE)

Bolt Size

(Metric)

1/4-20 M6 x 1.0 6 10 14 13

5/16-18 M8 x 1.25 12 19 29 31.4

3/8-16 M10 x 1.50 20 33 47 62

7/16-14 32 54 78

1/2-13 M12 x 1.75 47 78 119 108

9/16-12 M14 x 2.00 69 114 169 173

5/8-11 M16 x 2.00 96 154 230 269

3/4-10 M18 x 2.50 155 257 380 372

7/8-9 M22 x 2.50 206 382 600 716

3/4 Anchor Bolts 75 MIN 110 MAX

Torque Recommendations

DIMENSIONS ARE IN MM

☺

REVISION

REV

DESCRIPTION

DATE

EDITED BY

ECO#

ADDED (2) 5540075, REPLACED 5530314 WITH

5530261, REPLACED 5540001 WITH 5540075,

UPDATED BOM REVISION AND NEXT ASSEMBLIES

06/17/2013

00605

UPDATED BOM REVISION

05/29/2014

00649

H-001

REPLACED 5505113 WITH 5505001

UPDATED NEXT ASSEMBLIES

10/06/2014

12/17/2015

00663

00738

NEXT ASSEMBLY

5250042

5250038

ITEM NO

PART NUMBER

DESCRIPTION

QTY

REV

1 5505001

GP-7/PL-6000/XPR SERIES SAFETY CLEVIS PIN

2 5715196

XPR PLASTIC COVER BLOCK 105 x 80

3 5550183

FTG ELB -06 JIC -06L ORB

4 5505350 MODEL#211 HAIR PIN/ LARGE 2

5 5530261

PHPS M6 x 1 x 10

6 5545347

WASHER, M12 FLAT WASHER

7 5535354

NUT M12 x1.75

8 5535001

NUT M8 x 1.25 NL

9 5530010

HHB M8 x 1.25 x 25

10 5545200

WASHER M10 x Ø18 SL

11 5535998

NUT M10 x 1.5

12 5530760

HEX HEAD BOLT M10x1.25x35

13 5540075

2.5 WIRE DIA., Ø20.5 x 75 LG

14 5550147

FTG NPL -04 JIC x -04 NPT

15 5550178

FTG TEE -04JIC -04JIC -06NPT

16 5550109

FTG ELB -06 JIC x -06 F NPT

17 5545535

C WASHER SHIM FOR LIFTS

18 5545341

WASHER M10 x Ø20 FLAT

19 5535013

NUT M10 x 1.5 NL

20 5505031

ROTOR CLIP 12mm SS

SHEET 1 OF 1

REV

DWG. NO.

SIZE

TITLE:

NAME

DATE

CHECKED

DRAWN

1645 LEMONWOOD DR.

SANTA PAULA, CA 93060

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS DRAWING IS

THE SOLE PROPERTY OF

BENDPAK INC.

ANY

REPRODUCTION IN PART OR AS A WHOLE WITHOUT

THE WRITTEN PERMISSION OF

BENDPAK INC.

PROHIBITED.

NOTE: UNLESS OTHERWISE SPECIFIED

5174114

XPR-9D/12FD PARTS BAG

02/10/2010

DO NOT SCALE DRAWING

1:18

SCALE:

THIRD ANGLE PROJECTION

02/19/2016

SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING

DIMENSIONS ARE IN MM

☺

REVISION

REV

DESCRIPTION

DATE

EDITED BY

ECO#

UPDATED BOM REVISIONS

12/01/2014

00673

UPDATED BOM REVISIONS

05/14/2015

00689

UPDATED BOM REVISIONS AND NEXT ASSEMBLIES

12/08/2015

00738

NEXT ASSEMBLY

5260568

5260570

ITEM NO

PART NUMBER

DESCRIPTION

QTY

REV

1 5215356

XPR-12FD POWER SIDE POST ASSEMBLY

2 5215233

XPR-12FD OFF SIDE POST ASSEMBLY

3 5210047

XPR-12FD GROUND PLATE

SHEET 1 OF 1

REV

DWG. NO.

SIZE

TITLE:

NAME

DATE

CHECKED

DRAWN

1645 LEMONWOOD DR.

SANTA PAULA, CA 93060

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS DRAWING IS

THE SOLE PROPERTY OF

BENDPAK INC.

ANY

REPRODUCTION IN PART OR AS A WHOLE WITHOUT

THE WRITTEN PERMISSION OF

BENDPAK INC.

PROHIBITED.

NOTE: UNLESS OTHERWISE SPECIFIED

5245137

XPR-12FD LIFT

SUPERSTRUCTURE

02/12/2010

DO NOT SCALE DRAWING

1:30

SCALE:

THIRD ANGLE PROJECTION

02/23/2016

SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING

5900952

XPR-12FDL/12FDL-LWB

Otros manuales para XPR-12FDL

Tabla de contenidos

Otros manuales de Sistema de elevación de Bend-Pak

Bend-Pak

Bend-Pak Clearfloor 10APX Manual de usuario

Bend-Pak

Bend-Pak EXCEL Series Manual de usuario

Bend-Pak

Bend-Pak HD-7500 Series Manual de usuario

Bend-Pak

Bend-Pak XPR-10T Manual de usuario

Bend-Pak

Bend-Pak HDSO-14P Manual de usuario

Bend-Pak

Bend-Pak xpR-10C-168 Manual de usuario

Bend-Pak

Bend-Pak XPR-10A Manual de usuario

Bend-Pak

Bend-Pak EV2400SL Manual de instrucciones

Bend-Pak

Bend-Pak XPR-9F Manual de usuario

Bend-Pak

Bend-Pak HDS-27 Manual de usuario

Bend-Pak

Bend-Pak XPR-12CL Manual de usuario

Bend-Pak

Bend-Pak GP-7LCS Manual de usuario

Bend-Pak

Bend-Pak GP-9XLT Package Manual de usuario

Bend-Pak

Bend-Pak SP-7XF Manual de usuario

Bend-Pak

Bend-Pak xpR-10C Manual de usuario

Bend-Pak

Bend-Pak XPR-10 Series Manual de usuario

Bend-Pak

Bend-Pak HD-9SWX Manual de usuario

Bend-Pak

Bend-Pak HDS-35 Manual de usuario

Bend-Pak

Bend-Pak HDS-14LSX Manual de usuario

Bend-Pak

Bend-Pak HDS-40X Manual de usuario

Bend-Pak

Bend-Pak HD-12LS Manual de usuario

Bend-Pak

Bend-Pak LR-60P Manual de usuario

Bend-Pak

Bend-Pak HD-7ZM Manual de usuario

Bend-Pak

Bend-Pak HDS-14 Manual de usuario

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario