Bend-Pak LR-10000 Manual de usuario

1645 Lemonwood Dr.

Santa Paula, CA, 93060 USA

Toll Free (800) 253-2363

Tel: (805) 933-9970

bendpak.com

Low-Rise Scissor Lift

Installation and Operation Manual

Manual P/N 5900075 — Manual Revision B — August 2021

Models:

• LR-10000

Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

⚠

DANGER

Save these instructions! Read the

entire

contents of this

manual

before

using this product. Failure to follow the instructions

and safety precautions in this manual can result in serious injury or

death. Make sure all other operators also read this manual. Keep

the manual near the product for future reference. By proceeding

with setup and operation,

you agree that you fully understand

the contents of this manual

and accept full responsibility for

product use

Manual. LR-10000 Low-Rise Scissor Lift, Installation and Operation Manual, Manual Part Number 5900075,

Manual Revision B, released August 2021.

agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain

any rights to this content, and you will not use the copies for commercial purposes.

Trademarks. BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company,

product, and service names are used for identification only. All trademarks and registered trademarks mentioned

in this manual are the property of their respective owners.

Limitations. Every effort has been made to ensure complete and accurate instructions are included in this

manual. However, product updates, revisions, and/or changes may have occurred since this manual was

published. BendPak reserves the right to change any information in this manual without incurring any obligation for

equipment previously or subsequently sold. BendPak is not responsible for typographical errors in this manual.

You can always find the latest version of the manual for your product on the BendPak website.

Warranty. The BendPak warranty is more than a commitment to you: it is also a commitment to the value of

your new product. Contact your nearest BendPak dealer or visit www.bendpak.com/support/warranty for

full warranty details. Go to bendpak.com/support/register-your-product/ and fill out the online form to

Safety.Your product was designed and manufactured with safety in mind. However, your safety also depends

on proper training and thoughtful operation. Do not install, operate, maintain, or repair the unit without reading and

understanding this manual and the labels on the unit;

do not use your Lift unless you can do so safely!

Owner Responsibility. In order to ensure operator safety and maintain your product properly, it is the

responsibility of the product owner to read and follow these instructions:

• Follow all setup, operation, and maintenance instructions.

• Make sure product setup and use conforms to all applicable local, state, and federal codes, rules, and

regulations, such as state and federal OSHA regulations and electrical codes.

• Read and follow all safety instructions. Keep them readily available for operators.

• Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.

• Do not operate the product until you are certain all parts are in place and operating correctly.

• Carefully inspect the product on a regular basis and perform all maintenance as specified.

• Service and maintain the unit only with approved replacement parts.

• Keep all instructions permanently with the product and make sure all labels are clean and visible.

•Only use the Lift if it can be used safely!

Unit Information.

Enter the Model Number, Serial

Number

, and the Date of Manufacture from the label on

your unit

. This information is required for part or

warranty issues.

Model:

Serial:

Date of Manufacture

LR-10000 Low-Rise Scissor Lift 3P/N 5900075 — Rev. B — August 2021

Table of Contents

Introduction 3 Operation 29

Shipping Information 4 Maintenance 33

Safety Considerations 4 Troubleshooting 34

FAQs 6 Wiring Diagrams 35

Components 7 Labels 36

Specifications 8 Parts Diagrams 38

Installation Checklist 9 ALI Store 42

Installation 10 Maintenance Log 43

Introduction

This Manual describes the LR-10000, which is low-rise, frame-engaging Lift designed and engineered

for fast and easy wheel service. It is the perfect Lift for trucks and SUVs that many other Lifts cannot

handle.

The LR-10000 can raise Vehicles up to 10,000 lbs. (4,536 kg). ALI certified.

More information about the full line of BendPak products is available at bendpak.com.

This manual is mandatory reading for all LR-10000 users, including anyone who sets

up, operates, maintains, or repairs it

. Keep this manual on or near the equipment so that

anyone who uses or services it can read it. If you are having issues, refer to the Troubleshooting

section of this manual for assistance.

⚠DANGER Be very careful when setting up, operating, maintaining, or repairing this equipment;

failure to do so could result in property damage, product damage, injury, or (in very

rare cases) death. Make sure only authorized personnel operate this equipment. All

repairs must be performed by an authorized technician. Do not make modifications

to the unit; this voids the warranty and increases the chances of injury or property

damage. Make sure to read and follow the instructions on the labels on the unit.

Technical support and service is available from your dealer, on the Web at bendpak.com/support,

by email at support@bendpak.com, or by phone at (800) 253-2363, extension 196.

You may also contact BendPak for parts replacement information (please have the model and serial

number of your unit available) at (800) 253-2363, extension 191.

LR-10000 Low-Rise Scissor Lift 4P/N 5900075 — Rev. B — August 2021

Shipping Information

Your equipment was carefully checked before shipping. Nevertheless, you should thoroughly inspect

the shipment

before

you sign to acknowledge that you received it.

When you sign the bill of lading, it tells the carrier that the items on the invoice were received in good

condition.

Do not sign the bill of lading until

after

you have inspected the shipment.

If any of the

items listed on the bill of lading are missing or damaged, do not accept the shipment until the carrier

makes a notation on the bill of lading that lists the missing and/or damaged goods.

If you discover missing or damaged goods

after

you receive the shipment and have signed the bill of

lading, notify the carrier at once and request the carrier to make an inspection. If the carrier will not

make an inspection, prepare a signed statement to the effect that you have notified the carrier (on a

specific date) and that the carrier has failed to comply with your request.

It is difficult to collect for loss or damage after you have given the carrier a signed bill of lading. If this

happens to you, file a claim with the carrier promptly. Support your claim with copies of the bill of

lading, freight bill, invoice, and photographs. Our willingness to assist in helping you process your claim

does not make us responsible for collection of claims or replacement of lost or damaged materials.

Safety Considerations

Read this manual carefully before using your new product.

Do not set up or operate

the product until you are familiar with all operating instructions and warnings. Do not allow anyone else

to operate the product until they are also familiar with all operating instructions and warnings.

⚠WARNING California Proposition 65: This product contains chemicals known to the State

of California to cause cancer and birth defects or other reproductive harm. For

more information, visit www. P65warnings.ca.gov.

Important Safety Instructions

•Read and understand all safety warning procedures before operating the Lift.

•Make sure all Operators read and understand the Installation and Operation Manual.

Keep the

Manual near the device at all times

•The product is a Low-Rise Scissor Lift. Use it only for its intended purpose. Do not make any

modifications to the product.

•The product must

only

be operated by authorized personnel.

•While the Lift is in use, only the operator may be within 30 feet of the Lift.

•When the Lift is in motion, keep people and body parts well away from it.

•Keep loads centered and balanced on the Platforms.

•Never exceed the rated capacity of the Lift.

•You

must

wear OSHA-approved (publication 3151) personal protective equipment at all times

when installing, using, maintaining, or repairing the Lift: leather gloves, steel-toed boots, eye

protection, back belts, and hearing protection are

mandatory

•Always wear safety glasses! Everyday glasses only have impact resistant lenses, they are not

safety glasses.

•Keep hair, loose clothing, finders, and all body parts away from moving parts.

•Care should be taken as burns can occur from touching hot parts.

LR-10000 Low-Rise Scissor Lift 5P/N 5900075 — Rev. B — August 2021

•Do not operate equipment with a damaged power cord or if the equipment has been dropped or

damaged – until it has been examined by a qualified service person.

•Do not let a cord hang over the edge of a table, bench, or counter or come in contact with hot

manifolds or moving fan blades.

•If an extension cord is necessary, a cord with a current rating equal to or more than that of the

equipment should be used. Cords rated for less current than the equipment may overheat. Care

should be taken to arrange the cord so that it will not be tripped over or pulled.

•Always unplug equipment from the electrical outlet when not in use. Never use the cord to pull the

cord from the outlet. Grasp plug and pull to disconnect.

•Let equipment cool completely before storing away. Loop cord loosely around the equipment

when storing.

•To reduce the risk of fire, do not operate the equipment in the vicinity of open containers of

flammable liquids (gasoline).

•To reduce the risk of fire or electric shock, never overload receptacles. Refer to the labels for the

proper load on receptacles.

•To reduce the risk of electric shock, do not use on wet surfaces or expose to rain.

•Adequate ventilation should be provided when working on operating internal combustion engines.

•Consider the work environment. Keep the work area clean. Cluttered work areas invite injuries.

Keep areas well lit.

•Always make sure the Safety Locks are engaged before attempting to work on or near a Vehicle.

•Make a visual inspection of the product

before

using it. Check for damage or missing parts. Do

not use the product if you find any issues. Instead, take it out of service, then contact your dealer,

email support@bendpak.com, visit bendpak.com/support, or call (800) 253-2363.

•Make a thorough inspection of the product at least once a year. Replace any damaged or severely

worn parts, decals, or warning labels.

•BendPak recommends referring to the ANSI/ALI ALIS Standard (R2015) Safety Requirements for

Installation and Service for more information about safely installing, using, and servicing your Lift.

Symbols

Following are the symbols used in this manual:

⚠DANGER Calls attention to an immediate hazard that will result in injury or death.

⚠WARNING Calls attention to a hazard or unsafe practice that could result in injury or death.

⚠CAUTION Calls attention to a hazard or unsafe practice that could result in minor personal

injury, product, or property damage.

NOTICE Calls attention to a situation that, if not avoided, could result in product or property

damage.

Tip Calls attention to information that can help you use your product better.

LR-10000 Low-Rise Scissor Lift 6P/N 5900075 — Rev. B — August 2021

Liability Information

BendPak Inc. assumes no liability for damages resulting from:

• Use of the product for purposes other than those described in this manual.

• Modifications to the equipment without prior, written permission from BendPak Inc.

•Injury or death caused by modifying, disabling, overriding, or removing safety features.

• Damage to the equipment from external influences.

• Incorrect operation of the equipment.

Frequently Asked Questions

Question: How much weight can the LR-10000 raise?

Answer: The LR-10000 can raise Vehicles up to 10,000 pounds (4,536 kg).

Q: Can the LR-10000 be installed outside?

A: No. The LR-10000 is approved for indoor installation and use only.

Outdoor installation is

prohibited

Q: Can I put the Power Unit Stand on either side of the LR-10000?

A: Yes. The Power Unit Stand can be located on either side of the Lift. The drawing on the previous

page shows the Power Unit Stand on the left if you are looking at the Short Ramp end of the Lift.

Q: What if I want to raise a Vehicle that is slightly over the weight capacity of the Lift?

A: This is not an intended use of the product. We strongly recommend against trying to raise a

Vehicle that is heavier than the rated capacity.

Q: How many locking positions does my Lift have?

A: Three. This gives you multiple heights to which you can raise the Lift, so it is easy to find the right

height for the work you are doing.

Q: What do the Safety Locks do?

A: Safety Locks use gravity to hold the Platforms up, once they are engaged. Even if the Lift loses

power, the Platforms stay where they are if they were left engaged on a Safety Lock.

Only leave

your Lift either fully lowered or engaged on a Safety Lock!

Q: Which end of the LR-10000 is the “front”?

A: Neither. You can drive onto the Lift from either direction; there are ramps on both ends.

Q: The LR-10000 is described as “frame-engaging”, what does that mean?

A: it means the Platforms (actually, the Lift Pad or Lift Extensions on the Platforms) contact the

underside of the Vehicle to raise it, leaving the wheels free. Put another way, the Vehicle is

not

raised on its wheels, like a Vehicle on a Four-Post Lift.

Q: Anything else I should be aware of?

A: Do

not

remove all four of a Vehicle’s tires while it is on the LR-10000 and then lower the Vehicle all

the way to the ground. It will go down, but it will have a hard time coming back up again. The Lift

requires some space to build up enough upward force to raise a Vehicle.

LR-10000 Low-Rise Scissor Lift 7P/N 5900075 — Rev. B — August 2021

Components

LR-10000 components include:

•Power Unit. Provides Hydraulic Fluid to the Hydraulic Cylinders, which they use to raise the

Platforms. Connects to an external electric power source.

•Power Unit Stand. Holds the Power Unit. Provides Hydraulic Fluid and pressure to the

Hydraulic Cylinders.

•Hydraulic Hose Cover. Not shown. Covers the Hydraulic Hoses as the routed from the Power

Unit to the Frames.

•Short Ramps. Used to drive Vehicles onto or off of the Platforms.

•Hinged Ramps. Hinges up when the Platforms are raised. Located on the other end of the Lift

from the Short Ramps. Can also be used to drive Vehicles onto or off of the Platforms.

•Platforms. Flat steel plates that raise and lower. The Lift Pads or Lift Pad Extensions, which sit on

the Platforms, make contact with the underside of the Vehicle to raise and lower the Vehicle.

•Base. The bottom of the Lift, everything around the Platforms.

•Utility Trays. Built in to the Bases of the Lift, the Trays hold whatever you need them to hold.

•Hydraulic Cylinders. Push the Platforms up to raise a Vehicle, move down to lower a Vehicle.

•Safety Locks. Hold the Platforms in place while they are raised. The LR-10000 has three Safety

Lock positions, which lets you select the right Platform height for your needs.

•Safety Lock Release Handle. Moves the Platforms off the Safety Locks when you want to

lower the Lift. Must be on the same side of the Lift as the Long Hydraulic Hose and Power Unit

Stand.

•Lift Pads and Lift Pad Extensions. Blocks that make contact with the lifting points on the

Vehicle being raised. You can stack one Lift Pad Extension on one Lift Pad, but no more than that.

LR-10000 Low-Rise Scissor Lift 8P/N 5900075 — Rev. B — August 2021

Specifications

Model LR-10000

Lifting capacity 10,000 lbs. / 4,536 kg

ALift height w/Lift Pad and Extension 32" / 810 mm

BLift height w/Lift Pad 27.25" / 692 mm

CLift height 23" / 581 mm

DLowered height 4.5" / 113 mm

EPlatform width 24" / 610 mm

FWidth between Platforms 24" / 608 mm

GOverall width 85" / 2,162 mm

HPlatform length 53" / 1,344 mm

IOverall length 83.5" / 2,124 mm

Maximum hydraulic pressure 2,650 PSI

Lifting time ~35 seconds

Motor 110 VAC, 220 VAC, 50/60 Hz, 1 Ph

Specifications subject to change without notice.

LR-10000 Low-Rise Scissor Lift 9P/N 5900075 — Rev. B — August 2021

Installation Checklist

Following are the steps needed to install your LR-10000 Lift. Perform them in the order shown.

☐1. Review the installation Safety Rules.

☐2. Plan for Electrical Work.

☐3. Make sure you have the necessary Tools.

☐4. Select the Installation Site.

☐5. Make sure there is adequate Clearance on all sides of the Lift.

☐6. Select the Power Unit Stand location.

☐7. Create Chalk Line Guides.

☐8. Anchor the Bases.

☐9. Install the Safety Lock Release Handle.

☐10. Anchor the Power Unit Stand and Attach the Power Unit.

☐11. Learn about Hydraulic Fluid Contamination.

☐12. Learn about Liquid Thread Sealant.

☐13. Connect the Hydraulic Hoses.

☐14. Prepare the Power Unit (

Electrician required

☐15. Install a Power Disconnect Switch and Thermal Disconnect Switch (

Electrician required

☐16. Review the Final Checklist.

☐17. Leave the Manual for the owner/operator.

☐18. Perform an Operational Test.

LR-10000 Low-Rise Scissor Lift 10 P/N 5900075 — Rev. B — August 2021

Installation

This section describes how to install your LR-10000. Perform the steps in the order listed.

⚠WARNING

Only use the factory-supplied parts that came with your Lift

. If you use

parts from a different source, you void your warranty and compromise the safety of

everyone who installs or uses the Lift. If you are missing parts, visit

bendpak.com/support or call (800) 253-2363, extension 191.

The LR-10000 is supplied with installation instructions and concrete fasteners that meet the criteria set

by the latest version of the American National Standard “Automotive Lifts – Safety Requirements for

Construction, Testing, and Validation” ANSI/ALI ALCTV.

Lift buyers are responsible for any special, regional, structural, and/or seismic anchoring requirements

specified by any agencies or codes, such as the Uniform Building Code or International Building Code.

Safety Rules

When installing the Lift, your safety depends on proper training and thoughtful operation.

⚠WARNING Do not install this equipment unless you have automotive Lift installation training.

Always use proper tools, such as a forklift or crane, to move heavy components.

Do not install this equipment without reading and understanding this Manual and

the safety labels on the unit. Keep the Manual near the device at all times.

BendPak recommends referring to the ANSI/ALI ALIS Standard (R2015) Safety Requirements for

Installation and Service for more information about safely installing, using, and servicing your Lift.

Only fully trained personnel should be involved in installing this equipment.

Pay attention at all

times.

Use appropriate tools and equipment, when needed. Stay clear of moving parts.

⚠WARNING You

must

wear OSHA-approved (Publication 3151) protective equipment at all

times during the installation: leather gloves, steel-toed work boots, eye protection,

back belts, and hearing protection are

mandatory

Electrical Work

You will need to have a licensed, certified Electrician available at some point during the installation.

⚠DANGER All wiring

must

be performed by a licensed, certified Electrician.

The Electrician needs to:

•Connect the 220 VAC power source to the Power Unit. This is generally done near the

end of the installation. Note that installing the Power Unit and connecting the Power Unit are

separate procedures; they are done at different times in the installation process

. The Electrician

must provide a Power cord and a Plug and connect them to the Power Unit

•Install a Power Disconnect Switch. A Power Disconnect Switch gives you a way to shut

down the Lift in the event of an electrical circuit fault or emergency situation. Refer to Install a

Power Disconnect Switch for more information.

•Install a Thermal Disconnect Switch. A Thermal Disconnect Switch automatically shuts

down the Lift in the event of an overload or an overheated motor. Refer to Install a Thermal

Disconnect Switch for more information.

Otros manuales para LR-10000

Tabla de contenidos

Otros manuales de Sistema de elevación de Bend-Pak

Bend-Pak

Bend-Pak GP-7LC Manual de usuario

Bend-Pak

Bend-Pak XPR-10AS Manual de usuario

Bend-Pak

Bend-Pak XPR-9DT Manual de usuario

Bend-Pak

Bend-Pak XP Series Manual de usuario

Bend-Pak

Bend-Pak LR-5T Manual de usuario

Bend-Pak

Bend-Pak HD-973P Manual de usuario

Bend-Pak

Bend-Pak HD-7PBX Manual de usuario

Bend-Pak

Bend-Pak PL-6KDT Manual de usuario

Bend-Pak

Bend-Pak HD-12LS Manual de usuario

Bend-Pak

Bend-Pak XPR-12CL Manual de usuario

Bend-Pak

Bend-Pak GP-9F Manual de usuario

Bend-Pak

Bend-Pak XPR-10AS-168-LP Manual de usuario

Bend-Pak

Bend-Pak XPR-7TR Manual de usuario

Bend-Pak

Bend-Pak HDS-14LSX Manual del propietario

Bend-Pak

Bend-Pak PL-14000 Manual de usuario

Bend-Pak

Bend-Pak HDS-27X Manual de usuario

Bend-Pak

Bend-Pak HDS-40X Manual de usuario

Bend-Pak

Bend-Pak HD-14SS Manual de usuario

Bend-Pak

Bend-Pak HDS-18E Manual de usuario

Bend-Pak

Bend-Pak RBJ4500 Manual de usuario

Bend-Pak

Bend-Pak 5175153 Manual de usuario

Bend-Pak

Bend-Pak PL-6000DC Manual de usuario

Bend-Pak

Bend-Pak HD-9 Manual de usuario

Bend-Pak

Bend-Pak HDS-14 Manual de usuario

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario