Benchmark Scientific BeadBlaster 24 Manual de usuario

Instruction Manual

BeadBlaster™ 24

D2400

Homogenizer

Foreword

Thank you for purchasing a BeadBlaster™24 Homogenizer. This manual

contains instructions for the proper operation and care of this instrument.

Please read it carefully before operation and keep it available for future use.

Prior to initial operation:

Please check the instrument and the accessories against the packing list

when you first open the shipping carton. Report any damage, discrepancy,

or missing items to the supplier immediately.

Safety Warnings and Guidelines

1. Important operation information:

Read this manual carefully before attempting to operate the instrument.

2. Safety:

3. The operation, maintenance and repair of the instrument should comply with the

basic guidelines and safety warnings below. Noncompliance may interfere with

the useable life of the instrument and safety protection and may void the warranty.

Use this product indoors. Do not operate in a damp or wet

environment.

Before using the instrument, read the manual carefully. This instrument

is designed for use in laboratory environments and must be operated by

skilled personnel with the appropriate training.

Do not attempt to open the casing or repair the instrument. Disassembly

will void the warranty. If there is a service issue with the instrument,

please contact the supplier.

Read this manual prior to powering up the instrument. Pay special

attention to the guidelines and directions below and be familiar with

all safety warnings and guidelines.

Before operation, check to see that the voltage rating on the instrument

matches your local voltage. The rated electrical load of the outlet

should not be lower than that of the instrument's demand. If the power

cord is damaged, it should be replaced. Do not place the power cord

where it will have objects placed on it or where it will be walked on.

When unplugging the instrument, do not pull the plug out of the socket

by the cord.

4. Maintenance

The tube holder should be cleaned with a cloth dampened with a small amount of

alcohol. The outside of the unit can be cleaned with a damp cloth or mild

detergent if required.

The power switch is located on the rear of the instrument. After use,

the power to the instrument should be turned off. If the instrument will

not be used for a long period of time, it should also be unplugged and

covered with a cloth or plastic to keep it free of dust.

The instrument should be unplugged immediately and the supplier

contacted in the event of:

Liquid leaking into the instrument

Smoke or fire

Abnormal operation - ie sound or smell

The instrument has been dropped or outer housing damaged

Instrument function changes

Install the instrument in a cool, dry location free from dust, direct

sunlight or strong lights. The instrument should be placed away from

corrosive gasses, strong magnetic fields, and heat sources. Allow at

least 4 inches on all sides of the instrument for proper air circulation.

Be sure that the air vent at the back of the instrument is not blocked. If

using two instruments, they should be placed at least 3 feet apart.

If samples are processed for an extended time period, many

cycles or without a pause between cycles, thermal breakdown of

the sample tube may occur. Be sure to follow manufacturers

guidelines for lysing kits and tubes.

Always disconnect power to the unit before any cleaning procedure.

Do not apply cleaning solutions directly to the tube holder or chamber.

Do not use corrosive agents while cleaning. Do not submerge the

instrument.

Contents

CHAPTER 1 INTRODUCTION ------------------------------------------------------------------------------ 1

CHAPTER 2 SPECIFICATIONS ---------------------------------------------------------------------------- 2

1. NORMAL OPERATION CONDITIONS: --------------------------------------------------------------- 2

2. THE BASIC PARAMETERS AND CHARACTERISTICS----------------------------------------- 2

CHAPTER 3 BASIC INSTRUCTIONS--------------------------------------------------------------------- 3

1. STRUCTURE OVERVIEW-------------------------------------------------------------------------------- 3

2. OPERATION PANEL--------------------------------------------------------------------------------------- 4

3. DISPLAY------------------------------------------------------------------------------------------------------- 4

CHAPTER 4 OPERATION GUIDE------------------------------------------------------------------------ 5

1. LOADING TUBES------------------------------------------------------------------------------------------- 5

2. PROGRAM SELECTION---------------------------------------------------------------------------------- 7

3. PROGRAM SETTING-------------------------------------------------------------------------------------- 7

4. RUNNING AND STOPPING PROGRAMMED OPERATION------------------------------------ 8

5. MOTOR OVER TEMPERATURE PROTECTION--------------------------------------------------- 8

6. BEAD SELECTION----------------------------------------------------------------------------------------- 9

7. SAMPLE PREPARATION--------------------------------------------------------------------------------10

CHAPTER 5 TROUBLESHOOTING GUIDE ------------------------------------------------------------V

D2400 Homogenizer Manual Chapter 1 Introduction

─1─

Chapter 1 Introduction

The BeadBlaster™24 is a homogenizer for biological samples. It features high speed,

three-dimensional vibration and has a capacity for 24 samples.

Features:

Can break and crack most biological samples (animal and plant tissue,

soils, yeast, spores, microorganisms, etc.)

Processes 24 samples in a minimal amount of time.

On board memory for 50 programmed runs.

Run stops automatically if the cover is opened.

D2400 Homogenizer Manual Chapter 2 Specifications

─2─

Chapter 2 Specifications

1. Normal operating conditions:

Ambient temperature：5C 35C

The relative humidity：≤70%

Power：AC100-240V～50-60Hz

2. The basic parameters and characteristics

Type

Parameter

D2400

Display

OLED

Speed

4.00m/s~7.00m/s, in 0.05m/s increments

Cycle duration

1s~ 1min 30s, in 1s increments

Pause

1s~ 2min, in 1s increments

Number of Cycles

Programs

Sample Size

24 X 2.0ml tubes

Acceleration time

＜2s

Deceleration time

＜2s

Noise

＜68db

Power

600W

Dimension(WXDXH)

280mm × 360mm × 385mm

Weight（kg）

25.0kg

D2400 Homogenizer Manual Chapter 3 Basic instructions

─3─

Chapter 3 Basic instructions

This chapter focuses on the structure, operation keys and display of the instrument, as well as

preparatory work before starting. Please read this chapter before initial operation.

1. Structure overview

Cover Latch

On/Off button

Power supply plug

Operation panel

Tube retainer

Display screen

Protective cover

Air opening

D2400 Homogenizer Manual Chapter 3 Basic instructions

─4─

2. Operation panel

3. Display

Prog. Use in conjunction with  to select the desired program.

Set Set speed, run time, cycle and pause time for the current program.

 Modify parameters

Start Run program

Stop Stop program

PROG：01 28ºC

6.50 03

0:30 0:30

SPEED

M/S

M:S

TIME

CYCLE

INTER..

M:S

D2400 Homogenizer Manual Chapter 4 Operation Guide

─5─

Chapter 4 Operation Guide

1. Loading Tubes

1.1 Disengage the locking latch (as shown below), turn the knob counter-clockwise and remove

the tube retainer.

1.2 The tube holder may be filled in or out of the instrument. To remove, simply lift off the shaft.

Place sample tubes into the tube holder and press down until seated. If less than 24

samples are used, they should be evenly distributed in the tube holder. If removed, the tube

holder can then be replaced, making sure the two bumps on the holder line up with the

indentations on the shaft.

Knob

Tube retainer

Locking latch

Sample tube

Tube holder

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Benchmark Scientific

Benchmark Scientific

Benchmark Scientific Accuris MyGel InstaView Manual de usuario

Benchmark Scientific

Benchmark Scientific Iso-Block BSH6000 Manual de usuario

Benchmark Scientific

Benchmark Scientific Accuris Manual de usuario

Benchmark Scientific

Benchmark Scientific Accuris SmartReader 96 Manual de usuario

Benchmark Scientific

Benchmark Scientific Bioclave Manual de usuario

Benchmark Scientific

Benchmark Scientific MR-9600 Manual de usuario

Benchmark Scientific

Benchmark Scientific SB-12L Manual de usuario

Benchmark Scientific

Benchmark Scientific TC9639 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario