Belkin P73213-A Manual de usuario
P73213-A F5U012
ExpressBus™Plus
User Manual
Thank you for purchasing the Belkin Components
ExpressBus™Plus! Now you have even more connectivity
without the headache of configuring cables, switches, or
complicated software and hardware setups. With the
ExpressBus™Plus, you can add three more USB ports, a
parallel printer port, and a serial (RS232) port, all from one
cable. Simply plug it in, pop in the floppy disk, and you’re
done! You don’t even have to reboot. Requires Windows®98.
Package Contents
(1) ExpressBus™Plus F5U012
(1) USB Device Cable 6 ft. (1.8m) F3U133-06
(1) Power Adapter
5 V DC, 2.0A
Registration Card P72009
Software Driver Diskette
This Manual
Introduction
1
Product Detail
2
Front View:
Power LED
USB_1 LED
USB_2 LED
USB_3 LED
Serial Port LED
Right Side View:
USB Downstream Ports
USB_1
USB_2
USB_3
Left Side View:
USB Upstream Port
Power Adapter Jack
Rear View:
Serial Port
Parallel Printer Port
Hardware Installation
1. Plug the Power Adapter into a wall
outlet, and the other end into the
Power Jack of the ExpressBus™Plus.
2. Plug in the included USB Device Cable
to the USB port of your PC. This end
of the cables has the flat connector.
3. Plug in the other end of the cable into the upstream port
of the ExpressBus™Plus. This end of the cable has a more
square shape. The first LED will light up in green.
At this point, a message in Windows®98 should appear
saying “New Hardware Found”.
3
Software Installation
4
Windows®98 Driver Installation
1. Windows®will detect "Generic USB Hub". Click “Next”.
2. Leave on "Search" and click “Next”.
3. Uncheck everything and click “Next”.
Windows®may prompt you to insert a Windows®98
installation CD. If so, insert the installation CD into your
CD-ROM drive and follow the system prompts.
4. Windows®will find the driver for "Generic USB Hub".
Click “Next”.
5. Windows®will install the Generic USB Hub driver.
Click “Finish”.
6. Windows®will detect "USB Ver 1.1 Device". Click “Next”.
7. Leave on “Search for the best driver for your device
(Recommended)”.
8. Select the “Floppy Disk Drives” box, make sure your Belkin
Windows®98 Driver Installation diskette has been inserted
into your floppy disk drive, and click “Next”.
9. Windows®will find the drivers for “Belkin F5U012(P) USB
Bay Serial Interface Controller”. Click “Next”.
10. Windows®will install the Belkin F5U012(P) USB Bay Serial
Interface Controller driver. Click “Finish”.
11. Windows®will detect "Unknown Device". Click “Next”.
12. Leave on "Search for the best driver for your device
(Recommended)" and click “Next”.
Software Installation (continued)
5
13. Select the "Floppy Disk Drives" box, make sure your Belkin
Windows®98 Driver Installation diskette is still inserted into
your floppy disk drive and click “Next”.
14. Windows®will find the drivers for "Belkin F5U012(P) USB
Bay Parallel Interface Controller". Click “Next”.
15. Windows®will install the Belkin F5U012(P) USB Bay Parallel
Interface Controller driver. Click “Finish”.
16. Windows®will detect "Serial on USB Port" and install the
driver automatically.
Driver installation is now complete.
Software Installation (continued)
6
Software Installation (continued)
7
Windows®98 SE Driver Installation
1. Windows®will detect "USB Ver 1.1 device". Click "Next".
2. Leave on "Search" and click "Next".
3. Select the "Floppy disk drives" box and make sure the
Belkin Driver Installation Diskette has been inserted into
your floppy drive. Click “Next”.
4. Windows®will find the drivers for "Belkin F5U012(P) USB
Bay Serial Interface Controller". Click "Next".
Software Installation (continued)
8
5. Windows®will install the Belkin F5U012(P) USB Bay Serial
Interface Controller driver. Click "Finish".
6. Windows®will detect "USB Device". Click “Next”.
7. Leave on "Search for the best driver for your device
(Recommended)".
8. Select the "Floppy Disk Drives" box, make sure your Belkin
Windows®98 Driver disk is still in your floppy disk drive
and click “Next”.
9. Windows®will find the drivers for "Belkin F5U012(P) USB
Bay Parallel Interface Controller". Click “Next”.
10. Windows®will install the Belkin F5U012(P) USB Bay Parallel
Interface Controller drivers. Click “Finish”.
11. Windows®will detect "Serial on USB Port", and will
automatically install the proper drivers.
Driver Installation is now complete.
Software Installation (continued)
9
To verify that the drivers are loaded, right-click on “My
Computer” and select properties. Click on the “Device
Manager” tab and you will see the device list as shown below.
The encircled devices are parts of the ExpressBus™Plus.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Hardware de red de Belkin
Belkin
Belkin Dual-Band Wireless A+G USB Network Adapter... Manual de usuario
Belkin
Belkin OmniView Manual de usuario
Belkin
Belkin F1DE101G Manual de usuario
Belkin
Belkin F1DU120 - Pulse Network Monitor Manual de usuario
Belkin
Belkin OmniView Manual de usuario
Belkin
Belkin F5D7230-4 Manual
Belkin
Belkin OmniViewIP 5000HQ Manual de usuario
Belkin
Belkin F5D8053 v6 Manual de usuario
Belkin
Belkin F1DNUSB-BLK Manual de usuario
Belkin
Belkin OmniView SMB F1DP101M Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
