Belfort ULTIMATE PB111 Instrucciones de funcionamiento

DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THE INSTRUCTIONS

IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

1. Never use the Booster Heat when solvent is in the machine.

2. Never attempt to heat solvent above 130 °F.

3. Always use a nonﬂammable solvent with a ﬂash point of 140 °F or higher.

4. The recovery bucket should be emptied each time the holding tank is ﬁlled.

5. Always make sure the ﬂoat travels freely up and down the rod after emptying the recovery bucket.

6. Always vacuum out the stainless steel tank and solution lines when switching from a solvent to a

water based detergent, and vice versa (see Operating Instructions).

7. Always use a drop cloth under the machine during operation.

8. Vacuum any unused solution out of the solution tank and empty the recovery bucket after each job.

9. Keep machine from rain and snow, extremes in temperatures, and store in a heated location.

Use the machine indoors. Do not use outdoors.

10. Do not run the pump dry.

11. Never operate a machine that is leaking or in need of a repair.

12. Always use a defoamer. The vacuum shut-off will not activate properly if foam is in the recovery

bucket. Water damage to the vacuum motor or other components will void the warranty.

If you have any questions before you operate the machine, call your supplier for instruction.

THE ULTIMATE®: PB111

EXTRACTOR

120V

INFORMATION

OPERATING

INSTRUCTIONS

12-2010

DO NOT SMOKE WHEN USING HYDROCARBON-BASED SOLVENTS

Even solvents with a ﬂash point above 140

F can be ignited, especially as an aerosol

from the wand.

56041876

FORM NO. 56041876 - Page 2

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories,

shops and ofﬁces other than normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the follow-

ing:

NOTE: Read all instructions before using this machine.

WARNING!

To reduce the risk of ﬁre, electric shock, or injury:

•Do not leave the machine unattended when it is plugged in. Unplug the unit from the outlet

when not in use and before servicing.

•To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

•Do not allow to be used as a toy. Close attention is necessary when used near children.

•Use only as described in this manual. Use only the manufacturer’s recommended attachments.

•Never add water over 130º F/54º C to the solution tank.

•Do not use with damaged cord or plug. If the machine is not working as it should, has been

dropped, damaged, left outdoors or dropped into water, return it to a service center.

•Do not pull by the cord, use the cord as a handle, close a door on the cord, or pull the cord

around sharp edges or corners. Do not run the machine over the cord. Keep the cord away from

heated surfaces. To unplug, grasp the plug, not the cord.

•Do not handle the plug, the cord or the machine with wet hands.

•Extension cords must be 12/3 and no longer than 50 feet. Replace the cord or unplug immedi-

ately if the ground prong becomes damaged.

•Do not put any object into openings. Do not use with any opening blocked; keep free of dust,

lint, hair, and anything that may reduce air ﬂow.

•Keep loose clothing, hair, ﬁngers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or

any health endangering dusts. Do not use to pick up ﬂammable or combustible liquids such as

gasoline or use in areas where they may be present.

•Turn off all controls before unplugging.

•Use extra care when cleaning on stairs.

•Connect to a properly grounded outlet only.

•Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure,or

chemical content.

•Use a respirator and gloves when using dry cleaning solvents. In addition, a fan or blower is

helpful to blow fumes away from the operator.

•Always work in a well ventilated area.

•Always work with the exhaust hose attached to the machine when using solvents.

INSPECTION:

Carefully unpack and inspect your #770 Ultimate for shipping damage. Each machine is tested and

inspected before shipping. Any shipping damage incurred is the responsibility of the carrier. You should

notify the carrier immediately if you notice damage to the box or to the machine or parts.

CLEANING SOLUTIONS:

The #770 Ultimate is capable of either wet or dry cleaning. Only liquid cleaners are recommended (no

powders). Solvents with a ﬂash point of 140° F or higher are required for safety. Solvents are normally

used full strength. Water based cleaners are normally diluted. Follow label directions. The stainless

steel holding tank can be ﬁlled with up to 3 gal. of cleaning solution.

MAINTENANCE:

For optimum performance, ﬂush the machine with clear water at the end of each working day. Once a

month, minimum, run a ﬂushing compound through the machine to break up any mineral or chemical

build-up that may have formed. Clean the ﬂoat rod each time the recovery bucket is emptied. Inspect

the ﬁlters regularly and clean as needed. The vacuum ﬁlter is located under the recovery bucket. The

solution ﬁlter is located at the bottom of the holding tank. The quick disconnects and castors can be

lubricated with a penetrating spray lubricant. Fine steel wool will keep the brass quick disconnects shin-

ning. An auto interior spray cleaner/protectant will work well to keep the body clean and bright.

Serial Number:___________________________

Model: Ultimate PBIII 120-B

Purchase Date: _________________

Write the name and phone number of your distributor:

_____________________________________

(and be sure to register your purchase to activate your warranty)

SPECIFICATIONS:

Construction:

Vacuum:

Heat Exchanger:

Circuit Board:

Sensing Systems:

Solvent Sensing Probe:

Pump:

Electrical System:

Weight:

Dimensions:

Stainless steel and hexane copolymer for use with solvents and water

based detergents

80” water lift - 97 CFM

Stainless steel coil, instant heat transfer

Solid-state technology, long life monitoring system controls heating

operation (sensing within 1º F)

Solid state circuitry

Determines whether there is solvent or water-base cleaning in holding

tank. (Patented) Unique fail safe system

automatically prevents solvent from heating above 125º F regardless of

heat setting

Centrifugal type 40 psi carbon and ceramic seals and brass head, slide-

mount and compression ﬁttings for quick removal and servicing

25 ft. 12/3 cord available in 120 & 240V 50/60 cycle

46 lbs.

23L x 22H x 10W

FORM NO. 56041876 - Page 3

FORM NO. 56041876 - Page 4

Set-Up

1 Make sure the recovery bucket is in place under the dome and in the correct position. The dome

must be ﬂat or it won’t seal properly.

2 Fill the stainless steel holding tank with cleaning solution, to the desired level. Solution must be at

least 3” above the ﬁlter in the bottom of the tank. NOTE: Attach the exhaust hose when dry

cleaning.

3 Position the cleaning tool over the holding tank, and depress the trigger. Turn the pump on (center

switch). Allow the solution to spray for several seconds, to ﬁll the lines.

4SOLVENT HEATING: turn on the Heater switch only. Make sure the Booster Heat switch is

turned completely off. Wait two minutes for the heater to reach operating temperature. Spray over

the holding tank again, for about 15 seconds, to preheat the solution line and the tool. NOTE: the

heat will shut off completely if the Booster Heat is turned on with solvent in the tank. Go to Step 5.

WATER HEATING: turn on the Heater switch, and position the Booster switch to the desired

temperature. Wait 2 minutes for the heater to reach operating temperature. Spray over the holding

tank for 15 seconds to preheat the solution line and the tool. Wait 30 seconds, then spray again for

15 seconds. Go to Step 5.

5 Turn on the Vacuum switch (ﬁrst switch). All rocker switches should be turned on now. You are now

ready to begin cleaning.

6 When the recovery bucket is full, the vacuum will automatically shut off. Turn the vacuum switch

off. Remove the dome and lift the bucket out. Empty the bucket, and wipe off any spillage from

the outside of the bucket. Reinstall the recovery bucket and the dome.

7 Make sure the ﬂoat in the bucket travels freely up and down the rod each time you empty the

recovery bucket.

TO SWITCH CHEMICAL BASE

8 When switching from a solvent-based product to a water-based detergent, or vice versa, use the

following procedure: turn off all the switches, except the vacuum switch. Leave the vacuum hose

in the dome, and disconnect the hoses from the tool. Place the open end of the vacuum hose into

the solution tank, and vacuum out any remaining solution. Place the hose over the ﬁlter in the tank

for 10 seconds.

9 Connect the end of the solution line to the black suction plug. Take the vacuum hose out of the

dome, and place the plug in its place. Let the vacuum run for 20 - 30 seconds to pull all the solution

out of the lines and the heater. NOTE: DO NOT LET THE PUMP RUN DRY.

SOLVENT HEATING:

WATER HEATING:

WATER ONLY

NO SOLVENT (E):

CAUTION:

Turn on the Heater Switch (D). The Booster Heat switch (E)

must be all the way off (turned counterclockwise until it ‘clicks’

off) or the machine will not heat at all.

Turn on the Heater Switch (D). Turn on the Booster Heat Switch

(E) to the desired temperature, 130 - 200

NOTE: Booster Heat will not work unless the Heat switch is on.

This indicator light (B) illuminates when the Booster Heat switch

(E) is turned on. It is a reminder that the Booster Heat will only

work with water-based solutions.

USE A RAG TO DISCONNECT BRASS FITTINGS

AFTER USING THE BOOSTER HEAT. THE FITTINGS CAN

GET VERY HOT AND MAY CAUSE MINOR BURNS.

AUTO VAC SHUT-OFF:

SOLVENT

SENSING SYSTEM:

When the recovery bucket is full, the vacuum motor will auto-

matically shut off. The ﬂoat in the bucket may not be raised by

foam. Defoamer must always be used to avoid water damage to

the vacuum motor.

This unique, patented system determines whether there is

solvent or water-based solution in the tank. If solvent is used,

the sensor will automatically prevent heating above 140

F. To

prevent accidental over-heating of solvent, the use of the Booster

heat switch - with solvent in the tank - will cause the entire heat

system to shut off.

A = VACUUM

B = WARNING INDICATOR

C = PUMP

D = HEAT

E = BOOSTER HEAT

55°C

100°C

50°C

ACD

NO SOLVENT

WATER ONLY

WHEN LIT

FORM NO. 56041876 - Page 5

FORM NO. 56041876 - Page 6

23 47 46

21A

18 19

3233

33B 32A

34A 34B

44 40

33A

26 27B

27A

THE ULTIMATE

Model PBIII

2/22/2010

53A

917A

FORM NO. 56041876 - Page 7

1 FP368 Vacuum Dome, no Gasket

2 439 Gasket, for dome

3 420 Handle, recovery Bucket

4 FP147 Recovery Bucket, complete

5 421 Float Rod

6 FP184 Float Assembly

7 423-120-240 Hour Meter, with bezel

8 1335 Switch Plate (no switches or lights)

9 118A Warning Indicator

14 FP578 Switch, rocker, with cover

15 FP246 Tank, S/S solution, complete

16 425 Gasket for Stainless Steel Tank, 15-1/2”

17 122 Knob, potentiometer

17A FP200B Potentiometer with Cable

18 80 Filter, pump inlet, S/S, 50 mesh

19 FP143 Probe, solvent sensor

20 19 Screw, twist-lock

21 450 Twist-lock

21A 123 Switch, reed, vacuum ﬂoat

22 424 Handle, lift, black

23 431 Vacuum Chamber

24 ULT-RED Body, red

25 928 Louver (includes screws)

26 45 Quick Disconnect, 1/4 m.p.t.

27 410 Guard, fan

27A 1496 Screws (Fan) 6/32” X 2”-1/4”

27B 16 Nut, nylon

28 412 Fan, cooling

29 459 Louver, 2-1/2” (includes screws)

30 426 Pump Cover, S/S

31 FP197A Pump Head w/ﬁttings

32 107 Compression Nut, 1/4”

32A 106 Compression Nut, 5/16”

33 FP151 Tubing, pump to tank with ﬁttings (1/4” I.D.)

33A FP149 Tubing, pump to heater with ﬁttings (1/4” I.D.)

33B FP150 Tubing, pump to tank with ﬁttings (5/16” I.D.)

34 104 Elbow, 1/8” X 5/16”, hose, f.p.t.

34A 100 Elbow, 1/8” X 1/4”, hose, m.p.t.

34B 104 Elbow, 1/8” X 5/16”, hose , f.p.t.

35 FP148 Pump, complete (120V)

36 435B Slide Bracket, male

37 435 Slide Bracket, female

38 156 Hose Clamp, 2-1/4”

39 FP163 Exhaust Hose, 2” X 13.5”, rubber

40 408 Vacuum Motor, 2-Stage

41 FP137 Castor Plate, complete

42 8 Nut, 1/4-20

ULTIMATE PB111

PARTS LIST

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION

43 413 Circuit Board, heat control

44 429 Heat Sink Plate

45 86 Grommet

46 440 Flange, exhaust

47 FP487 Filter, exhaust, 4”

48 419 Gasket, vacuum motor

49 447 Circuit Board, solvent sensor

50 409A Relay, vacuum

51 138 Bolt, Hex, 1/4” X 1-1/4”

52 FP138 Heat Exchanger, complete

53 455 Heat Exchanger Mount

53A 76A Hose Clamp, 2 3/4”

54 101 Coupling, 1/8 m.p.t.

55 103 Elbow, 1/8 m.p.t.

56 105 Nipple, reducer 1/4” X 1/8 p.t.

57 115 Washer, ﬁber

58 116A Washer, ﬁber

59 418 Castor

60 29 Screw, 1/4-20 x 1/2”

61 184 Cord Retainer

62 495A Power Cord, 25’, yellow

12-2010

MISELLANEOUS PARTS/KITS

FP144 Syphon plug

FP156 Exhaust hose, 10 ft

FP247 Heat repair kit

NOTES:

THE ULTIMATE®: PB111

EXTRACTOR

120V

Tabla de contenidos

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Zephyr

Zephyr Spruce AK9834BS Guía de instalación

Hisense

Hisense MH6INBG Manual de usuario

Miele

Miele DA 1255 Manual de usuario

Broan

Broan 46000 Manual de usuario

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Miele

Miele DA 6708 D Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

AEG

AEG X68163BV1 Manual de usuario

AEG

AEG 125 D Manual de usuario

Smeg

Smeg KSEV97X Manual de usuario