Beko BX B7S / BLED Manual de usuario

CONFIDENTIAL BX B7S / BLED

Heat Pump Tumble Dryer

September’ 17

Sensitivity: Public

Step 11: “Start/Pause” button is pressed. “Anti-Creasing Led” lights on. Motor start to rotate

in counter-clockwise direction. “Sound Warning Led” starts to blink and it is allowed to pass

to the next step.

Step 12: “Start/Pause” button is pressed. The service test program will be exited.

7. Service Test Program BLED:

Step 1: Press “Dryness Level(1)” and “Start/Pause(2)” button, then turn the “On/Off

Program Selection Knob(3)” 90 degrees in clockwise direction within 2 seconds.

These combination will start service test program. In this program “Start/Pause”

button is used to pass other steps. Blinking of “Sound Warning Led” means that the

step is OK and it is allowed to pass to the next step.(SHP : Service Test – Heat

Pump Type)

Step 2: “Start/Pause” button is pressed. All leds blink and service test program waits

another “Start/Pause”press.

CONFIDENTIAL

Beko2013

Good+

Heat Pump Tumble Dryer

September’ 17

Sensitivity: Public

Step 3: “Start/Pause” button is pressed. Version of main software is shown on

display and service test program waits another “Start/Pause”press.

Step 4: “Start/Pause” button is pressed. Revision of main software is shown on

display and service test program waits another “Start/Pause”press.

Step 5: “Start/Pause” button is pressed. Revision of parametric software and its

number are sequentially shown on display and service test program waits another

“Start/Pause”press.

Step 6: “Start/Pause” button is pressed. All leds light on and service test program

waits another “Start/Pause”press.

Step 7: “Start/Pause” button is pressed. The last error codes are shown on display.

In this section, this error codes could be deleted by service technician with “On/Off

Program Selection Knob”. Knob have to get position 180 degree according to inital

position as shown in the picture.

CONFIDENTIAL BX B7S / BLED

Heat Pump Tumble Dryer

September’ 17

Sensitivity: Public

Step 8: “Start/Pause” button is pressed. The door and compressor NTC are checked

in this step. If there is no short or open circuit sensation error, door NTC value and

compressor NTC value are sequentially shown on display and it is allowed to pass to

next step.

Door NTC Open Circuit : “d:OC” is shown on display

Door NTC Short Circuit : “d:SC” is shown on display

Compressor NTC Open Circuit : “h:OC” is shown on display

Compressor NTC Short Circuit : “h:SC” is shown on display

If NTC and voltage error occurs, it is not allowed to pass to the next step.

Step 9: “Start/Pause” button is pressed. “F On” appears on display. The compressor

cooling fan starts to work. “Sound Warning Led” starts to blink and it is allowed to

pass to the next step.

Step 10: “Start/Pause” button is pressed. “Pon” appears on display. The pump

activates. If the socket of the overflow micro switch is not connected, “Tank Full Led”

blinks. If it is connected, “Sound Warning Led” blinks and it is allowed to pass to the

next step.

Important Note: If “Tank Full Led” blinks, the overflow micro switch and cables have

to be checked.

Step 11: “Start/Pause” button is pressed. “Drr” appears on display. Motor rotates in

clockwise direction. After 3 seconds, “Sound Warning Led” starts to blink and it is

allowed to pass to the next step.

CONFIDENTIAL

Beko2013

Good+

Heat Pump Tumble Dryer

September’ 17

Sensitivity: Public

Step 12: “Start/Pause” button is pressed. Motor continues to rotate in clockwise

direction. “Clean Filter Led” starts to blink for humidity sensor short circuit control.

Open the door of tumble dryer and make the sensor short circuit by touching the

sensor plate. If short circuit control of humidity sensor is OK, “Clean Filter Led” stops

to blink, “Sound Warning Led” starts to blinks, “Sco” appears on display and it is

allowed to pass to the next step.

Important Note: At the step 10, the sensor plate needs to be short circuit in 10

seconds, otherwise short circuit error occurs. If error occurs “ScE” appears on

display. In this situation below steps must be followed:

1. Dryer must be switched off and service test have to be restarted.

2. If the same error is seen in second trial, a problem may be in humidity

sensor cables and sockets. Please check humidity sensor cables and

sockets.

3. A problem may be in humidity sensor.

4. If there is not a problem in above parts, a problem may be in main

board.

Step 13: “Start/Pause” button is pressed. All components stop. “StP” appears on

display. After 3 seconds, “Sound Warning Led” starts to blink and it is allowed to pass

to the next step.

Step 14: “Start/Pause” button is pressed. “Drr” appears on display. Motor starts to

rotate in clockwise direction. If humidity sensor is open circuit, “Sound Warning Led”

starts to blink and it is allowed to pass to the next step. If the sensor is not open

circuit, “Clean Filter Led” starts to blink and it cannot be passed to the next step till

the sensor is open circuit.

CONFIDENTIAL BX B7S / BLED

Heat Pump Tumble Dryer

September’ 17

Sensitivity: Public

Step 15: “Start/Pause” button is pressed. “Crn” appears on display. Compressor

starts to work. After that, compressor NTC value appears on display and the value

starts to increase. If the compressor NTC value reaches the 50-55 °C, “C on”

appears on display, “Sound Warning Led” starts to blink and it is allowed to pass to

the next step.

Step 16: “Start/Pause” button is pressed, “rLL” appears on display. Motor starts to

rotate in counter - clockwise direction. “Sound Warning Led” starts to blink and it is

allowed to pass to the next step.

Step 17: “Start/Pause” button is pressed. The last error codes are shown on display.

In this step, error codes cannot be deleted. It is allowed to finish the service test

program.

Step 18: “Start/Pause” button is pressed. The service test program will be exited.

CONFIDENTIAL

Beko2013

Good+

Heat Pump Tumble Dryer

September’ 17

Sensitivity: Public

Error Codes:

Error Codes Definition

E 00 : No error

E 01 : Door Opened While Running

E 02 : Tank Full

E 03 : Drum Empty

E 04 : Start While Door Open

E 05 : Maximum Time

E 06 : Door NTC: Open Circuit

E 07 : Door NTC: Short Circuit

E 08 : Door NTC: Overheat

E 09 : Compressor NTC: Open Circuit

E 10 : Compressor NTC: Short Circuit

E 11 : Compressor NTC: Overheat

E 12 : Belt Broken

E 13 : Filter Blocked

E 14 :

E 15 :

E 16 : Low Voltage (Lower than 165V)

E 17 : High Voltage (Higher than 265V)

E 18 : BLDC Communication Error (for tumble dryer with BLDC motor)

E 19 : BLDC System Pause (for tumble dryer with BLDC motor)

E 20 : BLDC RPM Tolerance (for tumble dryer with BLDC motor)

E 21 : BLDC Minimum RPM (for tumble dryer with BLDC motor)

E 22 : BLDC Reenergized (for tumble dryer with BLDC motor)

E 23 : BLDC Abnormal Voltage (for tumble dryer with BLDC motor)

E 24 : BLDC Overheat (for tumble dryer with BLDC motor)

E 25 : BLDC Locked Rotor (for tumble dryer with BLDC motor)

E 26 : BLDC Overspeed (for tumble dryer with BLDC motor)

E 27 : BLDC Overcurrent (for tumble dryer with BLDC motor)

E 31 : Combined Filter Not Mounted (for combined filter models)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Secadora de Beko

Beko

Beko DCU 8230 Manual de usuario

Beko

Beko DIH7452TA Manual de usuario

Beko

Beko DRYPOINT M PLUS DM 40-61 C-N Guía del usuario

Beko

Beko DCY 9316 W Manual de usuario

Beko

Beko DS 8133 G Manual de usuario

Beko

Beko DH9443CX0W Manual de usuario

Beko

Beko DPU 7340 X Manual de usuario

Beko

Beko DTLCE80051B Manual de usuario

Beko

Beko DRZ1025B Manual de usuario

Beko

Beko DS7431PX0 Manual de usuario

Beko

Beko DRXS712W Manual de usuario

Beko

Beko DRX923W Manual de usuario

Beko

Beko DRYPOINT RS 700-3500 HP45 NA Guía del usuario

Beko

Beko DC7W Manual de usuario

Beko

Beko B3T68110 Manual de usuario

Beko

Beko DCU8235BXT2 Manual de usuario

Beko

Beko DCUS 81 W Manual de usuario

Beko

Beko B3T6924WS Manual de usuario

Beko

Beko DCU 8230 Manual de usuario

Beko

Beko DTBP 7001 W Manual de usuario

Beko

Beko DU 8133 PA0W Manual de usuario

Beko

Beko DS 7433 CSRX Manual de usuario

Beko

Beko DRX823W Manual de usuario

Beko

Beko DRYPOINT AC Series Manual de usuario

Manuales populares de Secadora de otras marcas

Bosch

Bosch WTA79200GB Manual de usuario

Amana

Amana W10233410A Manual de usuario

Miele

Miele TWH 780 WP Manual de usuario

Asko

Asko T760 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manual de usuario

Bosch

Bosch Logixx 10 WTB76556GB Hoja de especificaciones

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manual de instrucciones

Electrolux

Electrolux EW2H328R2 Manual de usuario

Dawlance

Dawlance Spinner DS 6000 C Manual de usuario

Electrolux

Electrolux TP5080TW Manual de usuario

AEG

AEG TR838P4OB Manual de usuario

Indesit

Indesit IDV 75 Manual de usuario

Infiniton

Infiniton SD-DG85C Manual de usuario

BOMANN

BOMANN WT 5019 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Manual de usuario

Asko

Asko T793C Manual de usuario

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario

Frigidaire

Frigidaire CAQE7077KW0 Manual del propietario