Behringer ULM200M Manual de usuario

ULM200M /ULM200D Controls

1. POWER/STATUS LED

1. ▼ VOLUME Button (Mute/volume down)

2. ▲ VOLUME Button (Power on/unmute/volume up)

3. USB connector

5. Wireless Link Status LED

ULM200M /ULM200D Getting Started

1.Connect the ULM200D wireless receiver to the “WIRELESS ONLY!”USB connector on

wireless-enabled BEHRIINGER mixers, powered speakers or other compatible products, or to a

USB port on a computer.

2.Press and hold the ▲ button on the ULM200M wireless microphone to connect wirelessly to the

ULM200D receiver. The LED on the microphone will fl ash slowly during the connecting

sequence and will light solid once connected. If the ULM200M wireless microphone cannot

connect to a receiver, the microphone will automatically power down after 10 seconds.

3.Once connected, the ULM200M microphone will be set at a medium volume. Use the ▲ and ▼

buttons to adjust the volume

4. A long press of the ▼ button will put the ULM200M microphone into mute. The mute

condition is indicated by rapid fl ashing of the LED. If the user does not unmute within 60

seconds, the ULM200M microphone will power down to save battery life.

5. A short press of the ▲button will unmute the ULM200M microphone. If the ULM200M

microphone is unmuted more than 10 seconds after muting, it will return to the previous volume

level, if unmuted after less than 10 seconds it will be set to the minimum volume level.

6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone

will power down 10 seconds after the ULM200D wireless receiver is unplugged.

7. The LED in the ULM200M wireless microphone will indicate when the battery is low by

regular brief fl ashes.

8. Should the ULM200M wireless microphone become unpaired with the ULM200D wireless

receiver, the microphone can be re-paired from the powered down state by simultaneously

pressing the ▲ and ▼ buttons and moving the microphone to within 10 cm (4 inches) of the

ULM200D wireless receiver. The LED on the microphone will fl ash slowly during the pairing

sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair

to the receiver it will automatically power down after 10 seconds.

Specification

RF output <100 mW / +20 dBm

Operating range 120 m (Line of Sight)*

Dynamic range 92 dB, A-weighted**

Equivalent input noise -112 dBu

Frequency Response 20 Hz - 20 kHz, ±1 dB

(Wireless Link)

Sampling rate 48 kHz

Resolution 24-bit

Encoding 232 kbps SLAC

(Slightly Lossy Audio Codec)

Latency 14.5 ms

RF frequency 2.4 GHz ISM band

(2406 MHz - 2474 MHz)

18 channels

Power Supply current 70 mA @ +5 VDC

Battery type 2 x AA (LR6) Alkaline cells

Battery life >30 hours

Dimensions (W x D x H) 45.7 x 45.7 x 243.8 mm

(1.8 x 1.8 x 9.6")

Weight 0.4 kg (0.9 lbs)*

Achievable range will be dependent on nearby sources of RF interference and/or line of sight

obstacles.**Measured from analog input to analog output, unity gain operation without

LEGAL DISCLAIMERMUSIC

Group accepts no liability for any loss which may be suff ered by any person who relies either

wholly or in part upon any description, photograph, or statement contained herein. Technical

specifi cations, appearances and other information are subject to change without notice. All

trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK,

TURBOSOUND, BEHRINGER, BUGERA and DDA are trademarks or registered trademarks of

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding MUSIC

Group’s Limited Warranty, please see complete details online at music-group.com/warranty.

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible Party Name: MUSIC Group Services NV Inc.

Address: 5270 Procyon Street Las Vegas, NV 89118 USA

Phone Number: +1 702 800 8290

ULTRALINK ULM200M/ULM202D

complies with the FCC rules as mentioned in the following paragraph:

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment and receiver

•Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is

connected

•Consult the dealer or an experienced radio/TV technician for help

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

Important information:

Changes or modifi cations to the equipment not expressly approved by MUSIC Group can void

the user’s authority to use the equipment.

Operation in the 2.4 GHz ISM (Industrial, Scientifi c, Medical) frequency band may be subject to

interference from other transmitting equipment operating in this band. In the event of such

interference, please verify and reassign the transmitting channels of any potentially interfering

transmitting equipment.

RF EXPOSURE (USB Receiver):

The USB Receiver is intended to use exclusively with Behringer mobile host devices as indicated

in the user manual, it is not intended to connect to laptops or computers.

A distance of 20 cm shall be maintained between the antenna and users, and the transmitter may

not be co-located with any other transmitter or antenna.

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de micrófono de Behringer

Behringer

Behringer ULM300MIC Manual de usuario

Behringer

Behringer ULM302MIC Manual de usuario

Behringer

Behringer UL2000M Manual de usuario

Behringer

Behringer ULTRALINK UL2000B Manual de usuario

Behringer

Behringer UL 1000G2 Manual de usuario

Behringer

Behringer ULTRALINK ULM202USB Manual de usuario

Behringer

Behringer ULTRALINK ULM200USB Manual de usuario

Behringer

Behringer ULTRALINK ULB2000 Manual de usuario

Behringer

Behringer ULM300M Manual de usuario

Behringer

Behringer ULTRALINK ULM2000 Manual de usuario

Behringer

Behringer UltraLink ULM300D Manual de usuario

Manuales populares de Sistema de micrófono de otras marcas

Paso

Paso R824 Manual de usuario

Naxa

Naxa NAM-982 Manual de usuario

Motorola

Motorola PMNN4461 Manual de usuario

Xvive

Xvive U3 Manual de usuario

Tekon

Tekon DUOS Manual de usuario

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manual de usuario

Devine

Devine WMD-IE Manual de usuario

LG LF-D7150 Manual de usuario

GE S768DAV Manual de usuario

LD U305 HBH 2 Manual de usuario

Chainway

Chainway URA8 Manual de usuario

ORATOR

ORATOR D860TD Manual de usuario

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manual de usuario

Alpha Technologies

Alpha Technologies RBMS Manual de usuario

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manual de usuario

Shure

Shure UA844 Manual de usuario

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manual de usuario

Pyle

Pyle PDWM5000 Manual de usuario