BEGA 7263LED Manual

Installation and Technical Information

BEGA

CSA certiﬁed to U.S. and Canadian standards. Suitable

for wet locations.

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

Garden bollard



0$;

Anchorage post

Supply wiring

Bollard wiring

Set screws

Supply wiring

Luminaire 7263LED:

Housings: Garden bollard housing made of aluminum alloy with

matte safety glass. Anchorage post (supplied) made of galvanized

steel.

Electrical: 3.4W LED luminaire, 5 total system watts, -30°C start

temperature. Integral 12V AC driver provided. Standard LED color

temperature is 3000K with an 85 CRI.

Warranty: 3 year manufacturer warranty

Notice to Installer for 7263LED:

WARNING: LEDs are high-quality electrical components. Please

avoid opening upper electrical compartment and do NOT touch LED

module.

1. Compatible for use with 12-24V AC input voltage.

2. Voltage must NOT drop below 10V.

3. Turn main power OFF before start of installation.

7263LED installation:

1. Establish area for ﬁxture placement and prepare soil for

anchorage by digging a hole (12” maximum depth).

2. Dig a trench from the anchorage hole to the power source. Depth

of the trench will be determined by national, state, and local

codes.

3. Install at least 3” of pea gravel or similar in the bottom of the

anchorage hole for drainage.

4. Loosen (2) set screws on garden bollard to release anchorage

post.

5. Bring 12V-24V supply wiring into the bottom of the anchorage post

and feed through to the top until there is 12” of cable coming up

through the top of the anchorage post.

6. Bury supply wiring cable in trench.

7. Place anchorage post into hole and ﬁll in hole with packed soil,

making sure that the post is vertical and secure.

8. Make wire splices from supply wiring coming out of anchorage

post to bollard wiring coming down from bollard shaft. For

maximum wire run lengths, see table to the right.

9. Push splices into bollard shaft.

10. Mount bollard onto anchorage post until the bottom of the

bollard hits the ground. Tighten (2) set screws to secure bollard to

anchorage shaft.

11. Connect supply wiring to main power. Turn main power on.

Garden luminaire - low voltage 7263LED

Tools Required:

3mm hex key

Standard small slotted screwdriver

Digging tool

Protection Class: IP64

Weight: 6.3 lbs.

Dimensions

A: 4 3/8”

B: 27 1/2“

Lamp: Integral 3.2W LED Module

(No replacement necessary)

7263LED

10/8/2012

18 16 14 12 10

40 46 73 116 185 294

30 61 97 155 246 392

20 92 146 232 369 588

15 122 195 309 492 784

10 183 292 464 738 1176

5 366 585 928 1477 2353

WireSize(AWG)

Max.RunLength(ft)PerWireSize:2Voltdrop

Connected

LEDWatts

Replacement Parts:

LED Module LED-0234/830

LED Driver 75946

Installation and Technical Information

BEGA

CSA certiﬁed to U.S. and Canadian standards. Suitable

for wet locations.

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

Garden bollard

Anchor bolts

(by others)

Supply wiring

Bollard wiring

Set screws

Anchor base

Supply wiring

Anchor base ﬂange

Luminaire 7264LED:

Housings: Garden bollard housing made of aluminum alloy with

matte safety glass. Anchorage base made of hot-dip galvanized steel,

made for bolting onto foundation (by others) or other paved surfaces.

Electrical: 3.4W LED luminaire, 5 total system watts, -30°C start

temperature. Integral 12V AC driver provided. Standard LED color

temperature is 3000K with an 85 CRI.

Warranty: 3 year manufacturer warranty

Notice to Installer for 7264LED:

WARNING: LEDs are high-quality electrical components. Please

avoid opening upper electrical compartment and do NOT touch LED

module.

1. Compatible for use with 12-24V AC input voltage.

2. Voltage must NOT drop below 10V.

3. Turn main power OFF before start of installation.

4. Anchorage hardware provided by others.

7264LED installation:

1. Loosen (2) set screws on garden bollard to remove anchor

base and anchor base ﬂange.

2. Bring 12V-24V supply wiring into the bottom of the anchor base

and feed through to the top until there is 12” of cable coming up

through the top of the anchor base.

3. Fix anchor base to existing foundation or surface using sufﬁcient

anchor hardware, supplied by others.

4. Slide anchor base ﬂange over anchor base so it covers the anchor

bolts.

5. Make wire splices from supply wiring coming out of anchor

base to bollard wiring coming down from bollard shaft. For

maximum wire run lengths, see table to the right.

6. Push splices into bollard shaft.

7. Mount bollard onto anchor base until the bottom of the

bollard hits the anchor base ﬂange. Tighten (2) set screws to

secure bollard to anchorage shaft.

8. Connect supply wiring to main power. Turn main power on.

Garden luminaire - low voltage 7264LED

Tools Required:

3mm hex key

Standard small slotted screwdriver

Digging tool

Protection Class: IP64

Weight: 5.3 lbs.

Dimensions

A: 4 3/8”

B: 27 1/2“

Lamp: Integral 3.4W LED Module

(No replacement necessary)

7264LED

10/8/2012

18 16 14 12 10

40 46 73 116 185 294

30 61 97 155 246 392

20 92 146 232 369 588

15 122 195 309 492 784

10 183 292 464 738 1176

5 366 585 928 1477 2353

WireSize(AWG)

Max.RunLength(ft)PerWireSize:2Voltdrop

Connected

LEDWatts

Replacement Parts:

LED Module LED-0234/830

LED Driver 75946

Manuales populares de Luz exterior de otras marcas

Sealey

Sealey LED37 Manual de usuario

nordlux

nordlux VEJERS Guía del usuario

SImx

SImx ELITE LED LHTC637 Manual de usuario

GEV

GEV CAROLINE 10833 Manual de usuario

NEBO

NEBO NEB-LSP-0020 Manual de usuario

WE-EF

WE-EF PFL540 LED Manual de usuario

Lindby

Lindby 9949029 Manual de usuario

HEPER

HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento

HEPER

HEPER LW8034.003-US Instrucciones de instalación y funcionamiento

Maretti

Maretti VIBE S 14.6080.04.A Manual de usuario

HEPER

HEPER MINIMO Instrucciones de instalación y funcionamiento

LIGMAN

LIGMAN BAMBOO 3 Manual de usuario

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manual de usuario

urban ambiance

urban ambiance UQL1273 Manual de usuario

TotalPond

TotalPond 52238 Manual de usuario

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manual de usuario

LIGMAN

LIGMAN DE-20023 Manual de usuario