BEGA 44 009 Manual de usuario

Manuales populares de Luz exterior de otras marcas

Sealey

Sealey LED37 Manual de usuario

nordlux

nordlux VEJERS Guía del usuario

SImx

SImx ELITE LED LHTC637 Manual de usuario

GEV

GEV CAROLINE 10833 Manual de usuario

NEBO

NEBO NEB-LSP-0020 Manual de usuario

WE-EF

WE-EF PFL540 LED Manual de usuario

Lindby

Lindby 9949029 Manual de usuario

HEPER

HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento

HEPER

HEPER LW8034.003-US Instrucciones de instalación y funcionamiento

Maretti

Maretti VIBE S 14.6080.04.A Manual de usuario

HEPER

HEPER MINIMO Instrucciones de instalación y funcionamiento

LIGMAN

LIGMAN BAMBOO 3 Manual de usuario

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manual de usuario

urban ambiance

urban ambiance UQL1273 Manual de usuario

TotalPond

TotalPond 52238 Manual de usuario

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manual de usuario

LIGMAN

LIGMAN DE-20023 Manual de usuario

Installation and Technical Information

BEGA

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

Replacement Parts

Accessories

Please refer to the appropriate

accessory installation sheet for

further instruction when applicable.

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

Wall luminaires - stainless steel 44 009

Tools Required:

3mm hex key

Protection Class: IP65

Weight: 2.0 lbs.

Dimensions

A: 2-3/4 “

B: 14-7/8 “

C: 4 “

D: 3 “

Relamping/Maintenance

Carefully unscrew and remove lens with attached

gasket to relamp. Clean luminaire and lens using only

solvent-free cleansers. Replace lens.

Lamp: 1.9W LED

44 009

8/8/2018

Page 1 of 2

Description

Glass with gasket

Driver (120-277V)

LED Module (3000K)

LED Module (4000K)

Part No

11271541

76066

LED-0253/830

LED-0253/840

Notice to Installer for 44 009:

1. For wall applications only.

2. Mounts directly to recessed BEGA 19 538 wiring box (provided) using mounting

plate (provided).

3. In conformance with UL Standard 1598, a silicone based sealant MUST be

used between luminaire and supporting wall.

44 009 - installation:

1. Unscrew and remove glass lens.

2. Feed luminaire wiring through stainless steel mounting plate and into the wiring box.

3. Make supply wiring and luminaire wiring connections inside the wiring box:

MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE

NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE

GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE

4. Attach stainless steel mounting plate to 19 538 wiring box. (Figure 1)

5. Attach mounting strap to mounting plate using (2) 8-32 screws (by others).

6. Mount luminaire over mounting strap and tighten set screw at bottom of luminaire.

7. Replace lens.



















Figure 1 (Generic Image)

Small Opening Wiring Box 19 538

Installation and Technical Information

BEGA

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

Wall luminaires - stainless steel 44 009

44 009

8/8/2018

Page 2 of 2

Product Safety Warnings:

CAUTION - RISK OF FIRE. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND

THE HAZARDS INVOLVED. SUITABLE FOR WET LOCATIONS.

MIN 90°C SUPPLY CONDUCTORS.

ATTENTION - RISQUE D’INCENDIE. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT,

PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES

INHÉRENTS. CONVIENT AUX EMPLACEMENTS MOUILLÉS.

LES FILS D’ALIMENTATION 90°C MIN.