Becker M Manual de usuario
Installation manual
Drives and control units for roller
shutters and sun protection systems
2
Preface
Using the installation manual
The installation manual describes the commissioning of Becker tubular drives for
roller shutters and sun protection systems as well as the commissioning of specific
Becker control units.
This manual is intended for technicians who have been trained by Becker-Antriebe
GmbH.
It is essential that you follow the safety instructions for the installation and commissioning
of tubular drives and control units on pages 160-161 at the end of the installation manual.
Failure to observe these instructions can lead to serious injuries.
The installation manual does not replace the Assembly and Operating Instructions
supplied with Becker products.
Always observe the information in the installation manual as well as the Assembly
and Operating Instructions supplied with the product when operating or repairing
the system. Becker-Antriebe does not accept liability for damage or injury resulting
from improper use.
Subject to technical changes without notice.
3
Sun protection
Control units
Roller shutter
Control units
Sun protection
Drives
Radio technology
Roller shutterSun protectionRadio technology
Roller shutter
Drives
Contents
Roller shutter drive types ................. 4
Identification of the drive type .......... 6
M (M04) drives ............................... 8
M17 drives ................................... 12
PicoR+ drives ............................... 14
R(+) drives.................................... 18
RO+ (E02) drives ........................... 22
RP(+) drives ................................. 26
E03 drives .................................... 30
E14 drives .................................... 36
PR+ drives .................................... 40
E01 drives .................................... 44
PRF+ drives .................................. 50
PROF+ drives................................ 54
C01 drives ................................... 58
B01 drives .................................... 62
VC420-II control unit ..................... 66
VC4200B control unit .................... 68
SC431-II control unit ..................... 70
Drives for sun shading devices ....... 72
Identification of the drive type ........ 74
M (M04) drives ............................. 76
S(+) drives .................................... 80
PS(+) drives.................................. 84
E15 drives .................................... 88
E12 drives .................................... 92
SE-B(+) drives .............................100
SE+ K5 mute drives ......................104
E18 drives ...................................108
SE I1 drives .................................116
PSF(+) drives ...............................120
SEF I1 drives ................................124
C12 drives ...................................128
C18 drives ...................................134
SWS241 control set ......................140
SWS441/SWS641 control set ........142
SC211 control unit .......................144
VC470-II control unit ....................146
Centronic radio technology ...........148
B-Tronic radio technology ............154
4
General
Roller shutter drive types
Type M:
Drive with mechanical
limit switching
Type R(+):
(1997-2009)
Drive with electronic limit
switching and sensitive
obstruction detection
Type Pico R+:
(1999-2007)
Drive with electronic limit
switching for the mini
tube
Type RF(+):
(2000-2002)
Drive with radio receiver
(40 MHz) and sensitive
obstruction detection
Type PRF+:
(from 2003)
Drive with Centronic radio
receiver (868.3 MHz)
and point to point pro-
gramming
Type PR+:
(from 2005)
Drive with electronic limit
switching and point to
point programming
Type RP(+):
(from 2009)
Drive with electronic
limit switching, point to
point programming and
sensitive obstruction
detection
Type PROF+:
(from 2009)
Drive with Centronic radio
receiver (868.3 MHz),
point to point program-
ming and sensitive
obstruction detection
5
Roller shutter
Drives
Type RO(+):
(from 2010)
Drive with electronic limit
switching and sensitive
obstruction detection
Type B01:
(from 2012)
Drive with B-Tronic radio
receiver (868.3 MHz),
point to point program-
ming and sensitive
obstruction detection
Type C01:
(from 2013)
Drive with Centronic radio
receiver (868.3 MHz),
point to point program-
ming and sensitive
obstruction detection
Type E01:
(from 2014)
Drive with electronic
limit switching, point to
point programming and
sensitive obstruction
detection with reversal
Type E03:
(from 2016)
Drive with electronic
limit switching, point to
point programming and
sensitive obstruction
detection
Type E02:
(from 2016)
Drive with electronic limit
switching and sensitive
obstruction detection
(functions same as RO+)
Type E14:
(from 2017)
Drive with electronic limit
switching and point to
point programming
6
All other drives can be identified via the programming
unit. Connect the wires in the connecting cable of the
drive to the wires of the same colour in the program-
ming unit.
Press the programming button for 2 seconds.
If the drive produces a loud noise and the tube does
not turn, the drive is a type M. Replace the program-
ming unit immediately with one that is suitable for an
M drive.
If the drive clicks twice, an R(+) type or PicoR+ type
drive is installed.
If the drive clicks once or does not react, it is an RP(+),
RO+, PR+, E01, RF(+) or PRF+, PROF+, or B01 drive
type.
1 s
1 s
1 s
1 s
1 s
1 s
1 s
1 s
1 s
1 s
1 s
1 s
1 s
5 s
10 s
10 s
General
Which type of roller shutter drive has been installed?
The limit positions of the latest generation of drives
with electronic limit switching can be deleted and reset
via the existing operator control. To do this, proceed
as follows:
First, run the drive for 6 seconds in the UP or DOWN
direction.
Then perform the travel movements described opposite
to delete the limit positions. If the drive then clicks twice,
it is one of the following types: RO+, E01, E02, E03 or
E14.
Then reprogram the upper and lower limit positions in
the order described opposite. The drive clicks once to
confirm the programming action.
If the drive does not confirm by clicking once, it is an
E02 type or RO+ type drive.
If the drive stops sensitively when encountering an
obstruction when moving downwards, it is an E01 type
drive.
If the drive stops without reversing, it is an E03 type
drive.
If the drive reacts insensitively to the obstruction, it is
an E14 type drive.
Deleting the limit positions
Upper limit position
Lower limit position
7
Roller shutter
Drives
Turn the drive roughly 3 revolutions then press the
programming button again for 2 seconds (the drive
clicks again to indicate that a second limit position
has been set). Turn the drive roughly 1.5 revolutions
in the opposite direction and carry out the deletion
sequence:
- Press and hold the programming button
- Press and hold the button
- Release the programming button
- Press the programming button again until the drive
clicks twice.
If the drive does not react, it is an RF(+) (up to 2002),
PRF+ (2003–2009), PROF+ (from 2009 onwards),
C01 (from 2013 onwards) or B01 (from 2012) drive
with integrated radio receiver and bidirectional radio
control. The drive type can be identified by program-
ming the corresponding hand-held transmitter.
If the drive clicks twice, it is an RP(+), RO(+) or PR+
drive type.
Press the programming button again.
If the drive clicks twice again, it is an RO(+) (from 2010
onwards).
If the drive clicks once, it is a RP(+) or PR+ drive. You
have now programmed a limit position. Turn the drive 3
revolutions from the limit position.
If the drive runs without stopping, it is a PR+ (from 2003
onwards) drive.
If the drive stops and continues running, it is a PR+
(from 2009 onwards) drive.
8
Type plate
Wiring
Drives with mechanical limit switching must not
be connected in parallel to a control point. Dis-
charge of the capacitor could damage the limit
switches. This would cause the limit positions
to be “overrun”.
The changeover time for switching the running di-
rection must be at least 0.5 seconds. The switch
and controls must not execute simultaneous UP
and DOWN commands.
Mains
Drive
Drive 2Drive 1
M (M04) drives
Type designation: e.g. R 8/17 C M
R Size of drive
(tube diameter)
P - 35 mm
R - 45 mm
L - 58 mm
8/17 Rated torque/output speed
C Pluggable connecting cable
M Mechanical limit switching
Operating mode (short-period operation
S2)
After 4 minutes of continuous operation,
the drive must be allowed to cool off.
Serial number: e.g. 08 40 961630
08 Year 2008
40 Calendar week
961630 Consecutive number
Mains
9
Roller shutter
Drives
Information
Before installation, make sure that the
drive adapter safety catch has engaged
(is screwed tight).
Mark the position of the drive adapter
on the tube and drill a 4-mm hole at this
point.
Secure the drive adapter against axial
displacement in the tube using a screw
or a rivet.
The arrow on the drive head indicates the
direction of rotation . The limit position
is set on the corresponding adjuster, for
example, with the flexible setting tool
(item no. 49332000020).
Turning in the + direction increases the
range; turning in the - direction reduces
it.
The barrel may not be turned more than
38 revolutions in one direction.
10
Setting the limit positions
1. Setting the lower
limit position
After the tube is installed,
run the drive downwards
until it switches off auto-
matically. Using the flex-
ible setting tool, turn the
corresponding adjuster in
the + direction (clockwise)
until the tube is in a suitable
position for connecting the
roller shutter to the tube.
Switch off the DOWN di-
rection and connect the
roller shutters to the tube
(mount the springs).
M (M04) drives
Este manual sirve para los siguientes modelos
34
Tabla de contenidos
Otros manuales de Accionamiento de CC de Becker
Becker
Becker E12a Manual de usuario
Becker
Becker E12 Manual de usuario
Becker
Becker enocean P5-16 Manual de usuario
Becker
Becker E16-V1 Manual de usuario
Becker
Becker R35/8G Manual de usuario
Becker
Becker R8/17PRF+ Manual de usuario
Becker
Becker R12/17RO+ Manual de usuario
Becker
Becker C16 Manual de usuario
Becker
Becker Extended Features XR7/85 Manual de usuario
Becker
Becker P5/16PRF+A1 Manual de usuario
Becker
Becker P Series Instrucciones de funcionamiento
Becker
Becker VariAir VAU 4/4 Manual de usuario
Becker
Becker U30 Manual de usuario
Becker
Becker P5/16R+ Manual de usuario
Becker
Becker C12 PLUS Manual de usuario
Becker
Becker S01 Manual de usuario
Becker
Becker R7/17 Manual de usuario
Becker
Becker R8/17RF Manual de usuario
Becker
Becker enocean R30-17 Manual de usuario
Becker
Becker P5-20-C18 PLUS Manual de usuario
Manuales populares de Accionamiento de CC de otras marcas
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manual de usuario
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manual de lista de piezas
Chamberlain Garog
Chamberlain Garog D Series Manual de usuario
Parker
Parker PDS Series Manual de usuario
Festo
Festo DGC G Series Guía de configuración
Binks
Binks QS-5012-1-CE Manual de usuario
ABB
ABB RSYC-01 Manual de usuario
Rockwell Automation
Rockwell Automation PowerFlex 700S Manual del propietario
WEG
WEG DeviceNet CFW500 Manual de usuario
Siemens
Siemens SINAMICS G Hoja de datos
Siemens
Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento
SOMFY
SOMFY JR RU 30 Manual de usuario