BEARICUDA SAG HARBOR Manual de usuario

Safety Points and Other Considerations

Our products are built for use based on

proper installation and normal residential

use, on level ground. Please follow the

instruction manual when building your

shed and retain the manual for future

maintenance purposes.

Some of the safety and usage measures you may wish to consider include:

-snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep the

snow off the roof(s).

-if the product is elevated, any structural and building code requirements are solely the customer's

responsibility, and should be abided by.

-in high or gusty wind conditions, it is advisable to keep the structure securely grounded.

-have a regular maintenance plan to ensure screws, doors, windows and parts are tight.

Customer agrees to hold %HDULFXGD Partnership and any Authorized Dealers free

of any liability for improper installation, maintenance and repair.

Toll Free 1- www.EHDULFXGD.com  LQIR@EHDULFXGD.com

Page 1

8x4 6DJ+DUERU

Garden Shed

Assembly Manual

Revision #12

March 16, 2012

In the event of a missing or broken piece, simply call the %HDULFXGD,QF Customer

Support Line @ 1- within 30 days of the delivery of your

purchase. It is our commitment to you to courier replacement parts, free of charge,

within 10 business days of this notification. Replacement parts will not be

provided free of charge after the 30 day grace period.

Thank you for purchasing

an 8x4 6DJ+DUERU Garden

Shed. Please take the time

to identify all the parts prior

to assembly.

Thank you for purchasing our 8x4 Sag Harbor Garden Shed.

Please take the time to identify all the parts prior to assembly.

Parts List:

A. Floor Section

1 - 45 ½” x 75” Large Floor Joist Frame (2 Joists Unattached)

1 - 45 ½” X 21” Small Floor Joist Frame (2 Joists ATTACHED)

2 - 1 ½” x 3 ½” x 72” Floor Joists

5 - 1 ½” x 3 ½” x 45 ½” Floor Runners

1 - 5/8” x 45 3/8” x 74 7/8” Plywood

1 - 5/8” x 45 3/8” x 20 7/8” Plywood

B. Wall Section

4 - 45 ½” x 75” Wall Panels

1 - 45 ½” x 75” Window Wall Panel

1 - 12” x 73” Narrow Wall Panel

2 - 9” x 45 ½” Wall Extendors

2 - 45 1/4” Angled Wall Extendors

4 - 1 ½” x 2 ½” x 45 1/2” Wall Plates

1 - ¾” x 3 ½” x 70” Horizontal Wall Cleat

1 - ¾” x 3 ½” x 21” Horizontal Wall Cleat

Door, Jambs & Header

1 - 31” X 72” Full Door

1 - 1 ½” x 3” x 73” Door Jamb

1 - 2” x 3” x 45 ½” Door Header (Dado cut on edge)

C. Rafter & Roof Section

2 - Roof Panels 51 ½” x 55 ¾” (1-Left 1- Right )

6 - 1 ½” x 2 ½” x 54” Rafters

2 - ½” x 4” x 48” Front Soffit

2 - ½” x 3” x 48” Rear Soffit

4 - Filler Shingles - 5 1/2” Wide

1 - 8”x 96” Strip of Roofing Felt

D. Miscellaneous Section

(Skirting, Facia ,Trim & Misc. Parts)

2 - ½” x 4” x 54 1/8” Side Angle Cut Facia

2 - ½” x 4” x 50” Front Facia

2 - ½” x 4 ½” x 50” Rear Facia

6 - ½” x 4 ½” x 45 1/4” Bottom Skirting

4 - ½ x 2 ½” x 75” Corner Filler Trim

2 - ½” x 2 ½” x 78 ¾” Vertical Door Trim

2 - ½” x 2 ½” x 80” Front Side Corner Trim

4 - ½” x 2 ½” x 88 ¾” Rear/Middle Trim (Opt. Door Trim)

2 - ½ x 4 ½” x 78 ¾” Front Corner Trim

2 - ½” x 4 ½” x 88 ¾” Rear Corner Trim

1 - ½” x 1 ¾” x 32” Horizontal Door Trim

1 - ½” x 2 1/2” x 8 1/2” Horizontal Narrow Wall Trim

2 - ½” x 4” x 51 5/8” Roof Ridge Board

2 - Detail Facia Plate (Larger for Rear Facia)

1 - Window Insert

1- Window Trim Pkg - (1-24 1/16” angle cut / 3 -23”)

1 - Flower Box Kit

(Assembly Instuctions and Hardware found in Kit)

2 - ½” x 2 ½” x 72” Interior Vertical Door Stops

1 - ½” x 2 ½” x 36” Interior Horizontal Door Stop

1 - 45 ¼” Extra Piece of Wall Siding

Important:

The Sag Harbor Shed can be assembled in many different configurations. This Assembly Manual

illustrates the most common configuration with the door to the left front 8ft side and Window Wall to

right front 8 ft side.

If you choose to configure with Door on end (45 1/2” side) , please refer to end of the Assembly Manual

for required changes necessary to correctly assemble.

Note: Standard Sheds come with 1 Window Wall Panel. On all configurations, the Window Wall Panel

can be positioned in any location to best suit purchaser’s preference.

7ROO)UHHZZZEHDULFXGDFRPLQIR#EHDULFXGDFRP

Page 2

Note: All Trim, Facia and Bottom Skirting pieces will be positioned rough face out when installed.

8x4 S$*+$5%25 HARDWARE PACKAGE

Note: screws and nails shown actual size.

Tee Hinge x 3 Door Handle

Hardware Kit (Provided)

Safety Glasses Work Gloves

Safety Equipment Required (Not Provided)

Ladder

Screw Gun/Drill Tape Measure

Hammer Wood Clamp

Level Pliers

Tools Required (Not Provided)

1/8” Drill Bit

Barrel Bolt

Utility Knife

Simpson Strong

Tie x 8

Page 3

1 1/4” Finishing

Square Drive Bit

2 1/2”

1 1/4”

3/4”

Black

2”

Black

Plywood Floor

Large Floor

Joist Frame

Floor Joists (2)

Floor Runners (5)

Small Floor

Joist Frame

Exploded Floor Section

A. Floor Section Exploded view of all parts necessary to

complete Floor Section. Identify all parts

prior to starting. Note: Floor Footprint is

96” wide x 45 1/2” deep.

Foundation Material

not included.

1. Lay out Large Floor Joist Frame and 2 Floor Joists as illustrated above. Position Joists

equally in Floor Joist Frame. Use Small Floor Joist Frame as a template to determine joist posi-

tion. Position Joist flush with framing.

2. When correctly positioned, attach each Joist with 4 - 2 1/2” screws (2 per end). You can find

the Square Drive Bit for the screws in with the Hardware Kit Bag.

Flush

with

framing

Front of SpaceSaver

You can find the

Square Drive Bit, for

the screws, in the

Hardware Kit Bag.

Toll Free 1-877-232-7428 www.bearicuda.com [email protected]

Page 4

Note: Plywood position

is interchangeable

Door Location

3. With Floor Joist Frames positioned

together flush, attach with 6 - 2 1/2”

screws.

4. Position and attach Floor Runners to completed floor

frames with 6 - 2 1/2” screws per Runner. Make sure

Runners are flush with outside, front and rear floor framing,

but not overhanging. Make sure 4th Runner is placed

equally over seam where floor frames meet.

4th Runner

96”

45 1/2”

5. With Floor Runners attached, carefully flip the floor over and place on your foundation.

Caution - you may need 2 people to assist you. Be careful when laying floor down not to bend or twist

floor. Note: The floor will be flipped over and floor runners will sit on your foundation. It is important

to note that having a level foundation is critical. Choosing a foundation will vary between regions.

Typical foundations can be concrete pads or patio stones positioned underneath the floor runners.

6. When in place, level floor completely

before proceeding.

7. Position Plywood Floor pieces (2) on top of

completed floor joists.

Flush with Floor Framing

Toll Free 1-877-232-7428 www.bearicuda.com [email protected]

Page 5

To help level Floor, locate Shim Shingles (used in

packaging) found in the edges of each Roof Panel.

Front

B. Wall Section Exploded view of all parts necessary to

complete the Wall Section. Identify all parts

prior to starting.

Angled Wall

Extendors (2)

Door Header

Solid Wall

Panel (4)

Wall Plate (4)

Window Wall

Panel

Door Jamb

Narrow Wall

Panel

Horizontal

Wall Cleats

Wall Extendors (2)

Wall Plate

9. Locate 4 Solid Wall Panels and 4 Wall Plates. Attach Plates to bottom of studs of each wall panel

with 3 - 2 1/2” screws. Position plates flush with framing.

Page 6

8. Position Plywood so it sits almost flush with outside of floor joist framing (see Note). When

correctly positioned, attach to all floor joists with 1 1/4” screws. Use screws every 16”.

Note: Plywood is cut slightly smaller than

floor framing. Keep plywood seams tight.

10. Starting on Side, position a Solid Wall Panel on top of plywood floor. The

Wall Panel bottom framing will sit flush with floor framing. Wall siding will

overhang the floor. Important: Make sure all walls are aligned in their upright

position. If not ,water may leak into your shed. Unsure if panel is facing up or

down? Recently attached Bottom Plate is on bottom of panel.

11. Outside 2x3 framing of wall panel should be flush with outside of floor framing when

properly aligned. The Plywood is cut slightly smaller than floor framing. Keep plywood seams tight.

Note: Siding will overhang the floor by approx. 1/2”. When positioned correctly, locate 2nd Solid Wall

Panel and place in Corner.

Wall Plate Flush

with floor framing

Wall

Siding

Overhangs

Floor by

1/2”

12. Butt both vertical wall studs of side and rear walls together and attach with 3 - 2.5” screws.

Screw at the bottom, middle and top of stud to secure properly. Note: Drill pilot holes in studs to

prevent splitting.

Rear Solid Wall

Side Solid Wall

Optional - Caulking

seams will help prevent

moisture from entering

at seam. Caulking not

included in kit.

Do Not Attach Walls

To Floor until Step 30

Page 7

13. With the corner wall attachment complete, position the Second Rear Wall Panel in place so

bottom 2x3 wall framing is sitting flush with outside floor framing. Wall siding should overhang floor

by approximately 1/2”. When positioned correctly, attach both wall panel studs together as per

Step 12 with 3 - 2 1/2” screws.

14. With Rear Wall Panel in place, position other side wall panel on floor as per Step 10 & 11.

Rear Wall Panel

15. Secure side wall panel to rear wall panel as per Step 12. Next, locate Window Wall Panel and

place in front corner.

Do Not Attach Walls

To Floor until Step 30

Page 8

16. Align front corner Window Wall Panel as per Steps 11 & 12. using 3 - 2 1/2” screws to secure

wall studs together.

17. Locate Narrow Wall Panel and position once again so 2x3 bottom wall framing sits flush on floor

and wall siding overhangs. Note: Narrow Wall Panel is only 73” high.

18. Secure as per Step 12. 19. Locate 3” wide Door Jamb and place on

wall stud to the right of door opening.

Door Jamb

Page 9

20. Position Door Jamb flush against wall stud and floor. The Jamb is 3” wide and will sit flush to

outside of wall siding. When positioned correctly, secure Jamb using 4 - 2 1/2” screws.

21. Position and attach the Door Header to Door Jamb and Narrow Wall Panel top framing. Header

should sit flush with Door Jamb and Outside of Narrow Wall Panel Siding. Attach with

3 - 2 1/2” screws.

Dado cut on edge

22. Locate an Angled Wall Extendor and place on side wall panel frame. Note: lap siding of Wall

Extendor will cover lap siding of side wall.

Lap Siding

of panels will

fit together.

Page 10

Otros manuales de Almacenamiento al aire libre de BEARICUDA

BEARICUDA

BEARICUDA 6X3 Canterbury Shed Manual de usuario

Manuales populares de Almacenamiento al aire libre de otras marcas

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Manual de usuario

TYGO

TYGO Nyland Manual de usuario

Duratuf

Duratuf GL105 Manual de usuario

Viking

Viking SD5300SS Manual técnico

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Manual de usuario

ModuLaro

ModuLaro Lojo WC202200 Manual de usuario

Lifetime

Lifetime 6418 Manual de usuario

rollaway container

rollaway container ARPCA24 Manual de usuario

Duratuf

Duratuf Havelock Manual de usuario

X-METAL

X-METAL 4065 Manual de usuario

Outdoor Life Products

Outdoor Life Products FP2030 F Manual de usuario

Royalcraft

Royalcraft Faro 295L Storage Box Manual de usuario

Riverlea

Riverlea Duratuf KIWI KS3 Manual de usuario

OLT

OLT GS84D-FJ-Plywood Manual de usuario

Rubbermaid

Rubbermaid 5L45 Manual de usuario

garofalo

garofalo TUSCANY EVO Manual de usuario

Duratuf

Duratuf Kiwi MK1 Manual de usuario

Eden

Eden CA2988 Manual de usuario