BE&SCO Beta 900 Tortilla Oven Manual de usuario
1
WARNINGS
10/15/13
Shown with the optional
Dough Trolley Loader
Shown as a Right Exit
also available as a
Straight Exit or Left Exit.
!
POWER FAILURE WARNING
IN CASE OF POWER FAILURE, TURN OFF GAS AND FOLLOW
SHUT DOWN PROCEDURES FOR OVEN.
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS
OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
WARNING
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR
MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH.
READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.
INSTRUCTIONS AND WARNING CONTAINED IN THIS MANUAL MUST
BE READ, UNDERSTOOD AND FOLLOWED.
POST IN A PROMINENT LOCATION INSTRUCTIONS TO BE FOLLOWED IN THE
EVENT USER SMELLS GAS. THIS INFORMATION SHALL BE OBTAINED BY
CONSULTING YOUR LOCAL GAS SUPPLIER. AT A MINIMUM:
• TURN OFF GAS
• EXTINGUISH ANY EXISTING FLAMES
• CONTACT YOUR GAS SUPPLIER
• IF YOUR GAS SUPPLIER CAN’T BE REACHED, CONTACT
LOCAL FIRE DEPARTMENT
Beta 900 Tortilla Oven
Shown with Exit Conveyor and
Midwedge Tortilla Press.
2
Precautions
1623 N. San Marcos
San Antonio, Texas 78201
www.bescomfg.com
KEEP THE BETA 900 FREE AND CLEAR FROM COMBUSTIBLES.
DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION AIR.
DISCONNECT ELECTRICAL POWER PRIOR TO MAINTENANCE AND
CLEANING.
ALL MAINTENANCE AND CLEANING MUST BE PERFORMED ACCORDING
TO THIS MANUAL.
NEVER USE ANY SHARP OBJECTS, CAUSTIC OVEN CLEANER, OR
DEGREASER TO CLEAN MACHINE OR PRESS PLATES.
FOR EMERGENCY SHUT DOWN, PUSH MASTER SWITCH.
READ AND FOLLOW ALL THE DIRECTIONS IN THIS MANUAL. DO NOT
LOSE OR THROW THIS MANUAL AWAY. DO NOT USE BETA 900 UNLESS
YOU READ THE MANUAL.
DO NOT CONNECT TO A CIRCUIT OPERATING AT MORE THAN 150 VOLTS
TO GROUND.
!
!
!
!
!
!
!
!
3
Warnings ..................................................................................................................................................... 1
Precautions.................................................................................................................................................. 2
Table of Contents......................................................................................................................................... 3
Policy & Procedure for Returning BE&SCO Parts.......................................................................................
Storyboards, Delivery & Damage, Beta 900 Manual, Training DVD............................................................ 5
Installation Requirements............................................................................................................................ 6
Location & Placement of Machine............................................................................................................... 7
..............................................................................................................................11
..................................................................................................................................... 12
Gas Piping................................................................................................................................................. 13
Ventilation ..................................................................................................................................................
Initial Adjustments......................................................................................................................................
Assembly Instructions................................................................................................................................ 15
General Guidelines.................................................................................................................................... 17
Midwedge Installation................................................................................................................................ 18
Oven Control Panel ................................................................................................................................... 19
............................................................................................................................... 21
....................................................................................................................... 22
Shutdown Operation.................................................................................................................................. 23
Dough Making ...........................................................................................................................................
Tortilla Making............................................................................................................................................ 27
Recipes...................................................................................................................................................... 32
Cleaning Supplies......................................................................................................................................
Cleaning the Beta 900............................................................................................................................... 35
Troubleshoot Guide ...................................................................................................................................
Maintenance Press & Oven ......................................................................................................................
Closing Statement .....................................................................................................................................
Parts & Pictures Warning ..........................................................................................................................
Decal Locator Assembly ............................................................................................................................ 79
Warranty ....................................................................................................................................................
Table of Contents
Neither this manual nor any part may be reproduced or transmitted in any form or by any means, electronic or mechanical,
writing from Bakery Equipment & Service Co., Inc.
Procedure for Returning BE&SCO Parts:
may request a repair and return, advance replacement or a credit of the component. The Parts Department
an RA number. You have 10 working days to return the old part for full credit or you will be invoiced for the
new part.
2. Package the component and a detailed description of what is wrong with the component. Write the RA
BE&SCO - Parts Department
RA#
1623-27 N. San Marcos
San Antonio, TX 78201
To obtain warranty on return parts the customer or the end user will be responsible for that particular item to be
shipped back to BE&SCO. Freight is not covered under warranty, going or coming. BE&SCO recommends
that you insure any parts that are being returned to BE&SCO, as BE&SCO Inc. is not responsible for any
damage or loss that occurs during shipping. If the part is damaged or lost during shipping, BE&SCO will not
be responsible for repair or replacement of the parts.
Returning BE&SCO Parts:
To return any BE&SCO parts you must follow BE&SCO’s procedure for returning. No returns will be accepted
credit. This does not include wear and tear items as stated in our manual.
This warranty does not cover any defect due to or resulting from handling, abuse, misuse, improper
maintenance and cleaning, or harsh chemical action, nor shall it extend to any unit from which the serial
number has been removed or altered, or acts of God. Adjustments such as calibrations, leveling, tightening
of fasteners or plumbing connections normally associated with original installation are the responsibility of
the dealer or installer and not of BAKERY EQUIPMENT & SERVICE CO., INC.
Policy & Procedure for Returning BE&SCO Parts
5
We tightly pack all our equipment and strap them on heavy wooden skids before giving
them to the shipping company. After we give the merchandise to the shipping company, they are
responsible for delivering your purchase; therefore, BE&SCO will not be responsible for the loss or
damage of your shipment. If you nd your purchase damaged call the shipping company.
Delivery & Damage
The Beta 900 manual covers installation, operation, maintenance, cleaning, troubleshooting
and parts. It is very important to always have a copy of the Beta 900 Manual as reference. If you
loose your Beta 900 manual or need an extra copy of the Beta 900 Manual, call the BE&SCO
Manual
Every Beta 900 comes with a Operation & Cleaning DVD in English and Spanish. This
DVD will help with training on the Beta 900. If you need additional training for the Beta 900 contact
Operation & Cleaning DVD or VHS
Storyboards
The laminated poster included in your shipment is called a Storyboard. A Storyboard
describes how to operate or care for the machine in an easy, quick format. It should be posted on
a wall close by the machine. Both front and back have the same information but in two different
6
Installation Requirements
(ForaQualiedServicePerson)
below. Anyone else doing so could easily damage the Beta Max, hurt him or himself, and void
the warranty.
1.
2. Gas Pipings
3. Ventilation
Initial Adjustments
5. Assembly Instructions
A QualiedServicePerson
1.
also obey the state or local authorities having jurisdiction in reference to the National Fuel Gas
Code, NFPA 54-1984 and ANSI z223.1-1984, Section 1.4.
2.
person must also obey safety rules and requirements of the state or local authorities having
jurisdiction in reference to the National Electrical Code, ANSI/NFPA 70
3. Canadian installations should agree with “Installation Codes for Gas Burning Appliances and
7
In an open work area. This way anyone can access the Beta 900 easily, especially for
maintenance.
compartment will be restricted and stop proper ventilation.
On level ground and on a curb base.
Make sure it is far from any strong air currents.
Finally, before making any connections to the BETA 900, check the rating plate on the
A good spot would be the one where you meet all the above suggestions. See the
Location and Placement of Machine
8
Beta 900 with Straight Exit with optional Dough Trolley Loader
9
Beta 900 with Right Side Exit with optional Dough Trolley Loader
10
Beta 900 with Left Side Exit with optional Dough Trolley Loader
Tabla de contenidos
