Beamz FLOOD36UV Manual de usuario

FLOOD36UV

153.277 V1

Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and

have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from

shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to

the factory, it is important that the product be returned in the original factory box and packing.

If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water

might damage your unit. Leave the unit switched off until it has reached room temperature.

On the label on the backside of the unit is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all

other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No

dimmer or adjustable power supply.

Always connect the unit to a protected circuit (circuit breaker or fuse). Make sure the unit has an appropriate electrical ground to

avoid the risk of electrocution or fire.

The unit may be set up on a stable and even surface. By means of the fixing facilities of the baseplate, the unit can also be mounted upside down to a truss,

see below picture. For fixing, certified clamps with correct save working load are required. According to the figure, the quick lock bolts of the omega

brackets are placed into the openings provided in the base plate and turned clockwise until they lock (to the stop). The mounting place must be of

sufficient stability and be able to support a weight of 10 times of the unit’s weight. Secure the unit with a safety cable so that it cannot fall down.

When carrying out any installation, always comply European and national guidelines concerning rigging, truss and all other safety issues. Always let the

installation checked out by an authorized dealer !

If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX chain.

Always connect the output of one unit with the input of the next unit until all units are connected.

At the last unit, you must close the DMX line with a terminating resistor. Take an XLR connector and solder a 120 Ohm resistor

between signal (-) and signal (+) and connect it to the DMX output of the last unit in the line.

A000-Axxx

DMX address setting

4 Ch

DMX Channel mode

8Ch

CL01-CL09

Constantly bright area selection. CL09 is constantly bright.

CC01-CC99

Jump mode, the value is larger, the speed is faster.

EE01-EE99

Pulse mode, the value is larger, the speed is faster.

FF01-FF99

Fading mode, the value is larger, the speed is faster.

ST01-ST99

Strobe change, the value is larger, the speed is faster.

Sou1

Sound control jump mode

Sou2

Sound control pulse mode

Sou3

Sound control strobe mode

Sou4

Full effect control mode

R000-R255

Adjust brightness 1st segment, 0-100%

G000-G255

Adjust brightness 2nd segment, 0-100%

B000-B255

Adjust brightness 3rd segment, 0-100%

U000-U255

Adjust brightness 4th segment, 0-100%

Dimmer

000-255

1st segment, 0-100%

000-255

2nd segment, 0-100%

000-255

3rd segment, 0-100%

000-255

4th segment, 0-100%

Master dimmer

000-255

Dimmer, 0-100%

Sections

000-255

1st segment, 0-100%

000-255

2nd segment, 0-100%

000-255

3rd segment, 0-100%

000-255

4th segment, 0-100%

Strobe

000-255

Strobe, from slow to fast

Macro

000-255

Macro

Speed

000-255

Speed for channel 7

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de Beamz

Beamz

Beamz WH192 Manual de usuario

Beamz

Beamz BUV63 Manual de usuario

Beamz

Beamz MHL36 Manual de usuario

Beamz

Beamz Rage 1000 Manual de usuario

Beamz

Beamz MHL108 MK3 Manual de usuario

Beamz

Beamz 160.569 Manual de usuario

Beamz

Beamz COB30 UV Manual de usuario

Beamz

Beamz 150.765 Manual de usuario

Beamz

Beamz SnowW1800 Manual de usuario

Beamz

Beamz MULTIBOX Manual de usuario

Beamz

Beamz BAC300 Manual de usuario

Beamz

Beamz PAR 56 DMX Black LED 5mm 156 Manual de usuario

Beamz

Beamz 160.563 Manual de usuario

Beamz

Beamz 150.458 V2.0 Manual de usuario

Beamz

Beamz BBP96S Manual de usuario

Beamz

Beamz BS1200 Manual de usuario

Beamz

Beamz COB30RGB Manual de usuario

Beamz

Beamz 160.562 Manual de usuario

Beamz

Beamz BBP9 Manual de usuario

Beamz

Beamz 150.641 Manual de usuario

Beamz

Beamz BAC406 Manual de usuario

Beamz

Beamz Snow600 Manual de usuario

Beamz

Beamz FUZE 1910 Manual de usuario

Beamz

Beamz TP36 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario

KAM

KAM DMX Laser80 FScan Manual de usuario