Beaba MILKEO Manual de usuario
MILKEO
www.beaba.com
1
6
5
2
3
4
5
7
,
a e
f g h
b d
c
22° C
37° C - 70 ° C 60 ml – 270 ml 6g – 65g
6
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE.
1. Safety instructions
CAUTION, BURNING RISK
USE
-
ELECTRICAL CONNECTION
EN
VIGILANCE/CHILDREN
PRECAUTIONS
11
2. Legend
Product:
1Powder reservoir
2Water reservoir
3On button
4
5Mixing compartment
6Control panel
7Cleaning brush
Control panel:
aLock button
bHot water dispenser button
cSetting button
dBottle preparation button
eAuto-clean button
fTemperature indicator
gWater quantity indicator
hPowder quantity indicator
12
3. Switching on the product
- Pour the water into the water reservoir 2
- Pour the powder into the powder reservoir 1
- Plug in the product
- Press the power button. 3
pressingthe button. At the end of the cycle put on the powder reservoir.
- If you do not use the product for a period of 3 minutes, the control panel locks automatically. To unlock it, press the lock/
unlock button for 1,5 seconds
- You can lock the control panel manually by pressing the lock/unlock button for 1,5 seconds
- Press once on the settings button
Set the desired temperature with the + and – buttons
- Press again on
- Press again on
about the quantity of power, follow the indications in the next section.
- Press the settings button
- Place the bottle on the bottle stand 4selecting one of the two heights according to the size of the bottle
- Press the bottle preparation button to prepare a bottle.
The settings will be saved for the following bottles. Repeat the operation to change the settings. If you modify the quantity
13
5. Dosing the powder
To determine the quantity of powder, check whether your brand of powder indicates the weight of a measure.
• If the weight is indicated:
-Set the quantity of water at 60 ml
-Double the weight of a measure and set the quantity of powder at this value.
You can then modify the quantity of water, the powder/water ratio will be saved.
• If the weight is not indicated:
-Weigh out 3 measures to obtain a reference weight
-Set the quantity of water at 90 ml
-Set the quantity of powder at the reference weight
You can then modify the quantity of water, the powder/water ratio will be saved.
• If you cannot weigh out 3 measures, you can temporarily set 9 g of powder for 60 ml of water.
Note: The dosage of your baby bottle may vary slightly depending on the density of your milk powder.
6. Bottle preparation function
To prepare a bottle:
- Place the bottle on the bottle stand 4
- Press the preparation button to start the preparation
Press any button to stop preparation
14
7. Hot water function
This function is for dispensing hot water at 22 to 70°
The water is dispensed at the quantity and temperature indicated on the control panel 6. You can modify these values
in the same way as for bottle preparation
- Place a recipient on the bottle stand 4
-Press the hot water dispenser button to obtain hot water
Press any button to stop dispensing manually.
8. Auto-clean function
The auto-clean function produces hot water to clean the Mixing compartment 5
- Place a recipient able to contain at least 220 ml on the bottle stand 4
- Remove the powder reservoir
- Press the auto-clean button
- Check that there is enough water in the reservoir before starting the cleaning cycle.
- Replace powder reservoir
9. Cleaning
Cleaning :
1. If there is water on the surface of the product, wipe with a dry cloth. Be sure to lock the control panel with the lock
button 6
2. Do not place the product in a humid environment
3. When the product is not used for an extended period, we recommend that you unplug it
4. Verify and clean the mixing compartment regularly 5
15
5. Rinse and clean the powder 1and water 2reservoirs regularly. Usethe bottle brush to remove powder in the corners.
6. Do not use a hard brush, organic abrasive products, or organic solvents to clean the mixing compartment 5
7. Before storing the product, empty and clean the powder reservoir and the water reservoir. To empty any excess water
in the circuit, remove the water tank, press the cleaning button for 5 seconds to drain the water circuit. To restart the
product press the start button 3
10. Problem/Solution
Problem Possible causes Possible solutions
-
16
Otros manuales para MILKEO
2
Tabla de contenidos
Otros manuales de Calentador de biberones de Beaba
Beaba
Beaba Bib'secondes Manual de usuario
Beaba
Beaba BIB EXPRESSO BEA0206 Manual de usuario
Beaba
Beaba Bib'bain-marie Manual de usuario
Beaba
Beaba BABYMILK SECOND Manual de usuario
Beaba
Beaba Bib'secondes Manual de usuario
Beaba
Beaba Bib'Expresso Manual de usuario
Beaba
Beaba Bib'bain-marie Manual de usuario
Beaba
Beaba BABYMILK SECOND Manual de usuario
Beaba
Beaba MILKEO Manual de usuario
Beaba
Beaba Milk Prep Manual de usuario
