BEA SEAGLE ONE Manual de usuario
SEAGLE ONE
1
3
5
24
Specifications are subject to changes without prior notice.
Measured in specific conditions
TECHNICAL SPECIFICATIONS
DESCRIPTION
ENGLISH
UNIDIRECTIONAL OPENING SENSOR
FOR AUTOMATIC DOORS
1. main connector
2. potentiometer for field size adjustment
3. radar antenna (narrow field)
4. DIP-switch
5. cover
Technology:
Transmitter frequency:
Transmitter radiated power:
Transmitter power density:
Detection mode:
Min. detection speed:
Supply voltage:
Mains frequency:
Max power consumption:
Output:
Max. contact voltage:
Max. contact current:
Max. switching power:
Mounting height:
Degree of protection:
Temperature range:
Dimensions:
Tilt angles:
Material:
Weight:
Cable lenght:
Conformity:
microwave doppler radar
24.150 GHz
< 20 dBm EIRP
< 5 mW/cm²
motion
5 cm/s (measured in sensor axis)
12 V to 24 V AC ±10%; 12 V to 24 V DC +30% / -10%
50 to 60 Hz
< 2 W
relay (free of potential change-over contact)
42 V AC/DC
1 A (resistive)
30 W (DC) / 60 VA (AC)
from 1.8 m to 3 m
IP54
from -20 °C to + 55 °C
120 mm (L) x 80 mm (H) x 50 mm (W)
0° to 90° vertical; -30° to +30° lateral
ABS
165 g
2.5 m
RED 2014/53/EU
Other use of the device is outside the permitted purpose and can not be
guaranteed by the manufacturer. The manufacturer cannot be held responsible
for incorrect installations or inappropriate adjustments of the sensor.
Please keep for further use
Designed for colour printing
For product version 0100 and more
This user’s guide is an informative document and
can not be seen as a commitment of result.
Before fixing After fixing
Avoid proximity to neon
lamps or moving objects.
Do not cover the sensor.Avoid vibrations.Do not touch electronical
parts.
Wall mounting above sliding or
revolving doors Ceiling mounting in front of sliding,
revolving or swing doors
(outside of the door motion range)
OPENING THE SENSOR
TIPS
APPLICATIONS
Mounting on door axis (swing doors)
2
23
1
MIN
ON
OFF
MAX
1
2.2 m
2.2 m
ADJUSTMENTS
Apply the mounting template.
Drill 1 hole for the cable and
pull it through.
Drill 2 holes for the screws.
Fix the sensor firmly.
FIELD ANGLE
Pull the cable through the hole
and connect the wires as follows:
1 - BROWN - POWER SUPPLY
2 - GREEN - POWER SUPPLY
3 - WHITE - COM
4 - YELLOW - NO/NC
Ceiling mounting in front of sliding,
revolving or swing doors
(outside of the door motion range)
FIELD SIZE DIP-SWITCH
DIP 1
DETECTION MODE
DIP 2
OUTPUT CONFIG.
DIP 3
PRM-MODE
(DIP 1 = ON)
DIP 4
IMMUNITY FILTER
bidirectional
unidirectional
active - NO
passive - NC for PRM
normal
high
normal
PRM= persons with
reduced mobility
field size: max
vertical angle: 30°
2.2 m 2.2 m
MOUNTING & WIRING
FIELD WIDTH
4 m x 2 m (wide)
2 m x 2.5 m (narrow)
Available as accessory
2.2 m
2.2 m
BEA SA | LIEGE Science Park | ALLÉE DES NOISETIERS 5 - 4031 ANGLEUR [BELGIUM] | T +32 4 361 65 65 | F +32 4 361 28 58 | [email protected] | WWW.BEA-SENSORS.COM
1
1
2
3
4
5
1
2
3
1
2
1
3
1
2
©BEA | Original instructions | 42.8143 / V2 - 07.18
BEA hereby declares that the SEAGLE ONE is in conformity with the basic requirements and the
other relevant provisions of the directive 2014/53/EU and 2011/65/EU (RoHS).
The complete declaration of conformity is available on our website
TROUBLESHOOTING
The door remains
closed.
The LED is OFF.
The sensor power is off. Check the wiring and the power supply.
The door does not
react as expected.
The door closes and
opens constantly.
Improper output
configuration on the sensor.
The sensor is disturbed by
the closing of the door or
vibrations caused by the
door motion.
The door opens for
no apparent reason.
It rains and the sensor
detects the motion of the
rain drops.
Change the output configuration setting on
each sensor connected to the door operator.
Make sure the sensor is fixed properly.
Make sure the detection mode is unidirectional.
Increase the antenna angle.
Increase the immunity filter.
Reduce the field size.
Change the antenna angle.
Decrease the field size.
Increase the immunity filter.
Make sure the detection mode is unidirectional.
Increase the immunity filter.
Install the ORA (rain accessory).
In highly reflective
environments, the sensor
detects objects outside of its
detection field.
In airlock vestibules,
the sensor detects the
movement of
the opposite door.
Change the antenna angle.
Increase the immunity filter.
This product should be disposed of separately from unsorted municipal waste
Otros manuales de Accesorios de BEA
BEA
BEA Nema 4 Flex IR Manual de usuario
BEA
BEA 1SAFE Manual de usuario
BEA
BEA IXIO-ST Manual de usuario
BEA
BEA COLIBRI ONE DRO Manual de usuario
BEA
BEA IXIO-DT3 Manual de usuario
BEA
BEA LZR SIGMA Manual de usuario
BEA
BEA LZR-MICROSCAN1UT Manual de usuario
BEA
BEA Jamb Style PBJ Series Manual de usuario
BEA
BEA Iris Overhead Safety for Door Manual de usuario
BEA
BEA ACTIV8 THREE F Manual de usuario
BEA
BEA CONDOR Manual de usuario
BEA
BEA FALCON Manual de usuario
BEA
BEA MAGIC SWITCH CHROMA Manual de usuario
BEA
BEA CONDOR ID Manual de usuario
BEA
BEA Eagle One HM Manual de usuario
BEA
BEA WIZARD-C Manual de usuario
BEA
BEA LZR RS300 Manual de usuario
BEA
BEA MINI FLY Manual de usuario
BEA
BEA Eagle HM Manual de usuario
BEA
BEA Superscan Manual de usuario
