BBB Alfa HT1 Manual de usuario
Valve Tester
Alfa HT1
Instruction Manual
AF99999
VALVE TESTER ALFA HT1
AF99999
2
v2.0
Index
1. Safety precautions ...................................................................................................................3
2. Equipment cleaning .................................................................................................................4
3. Introduction ..............................................................................................................................5
4. Technical data ...........................................................................................................................6
5.
Equipment composition ..........................................................................................................7
6. Operation ..................................................................................................................................8
7. How to use ............................................................................................................................. 11
8. Test result .............................................................................................................................. 20
9.
System icons and Indicators.. ............................................................................................... 21
10. Troubleshooting ................................................................................................................. 22
11. Connectivity and updates ................................................................................................. 22
12. Guarantee ............................................................................................................................ 24
13. Rights Policy ........................................................................................................................ 25
3
v2.0
VALVE TESTER ALFA HT1
AF99999
1. Safety precautions
This product complies with the requirements of the following Directives and
Certifications of the European Community : 2014/35/EU of Low Voltage and
2014/30/EU of Electromagnetic compatibility.
•UNE EN 62368-1: 2020
•UNE – EN 61000-3-2:2019
•UNE – EN 61000-3-3:2013+A1:2020
•UNE-EN 55032:2016 +AC:2016-07 Class A
•UNE-EN 55035:2017+A11:2020
To ensure the proper functioning ofthe equipment and eliminate the danger ofdamage,
the following precautions must beobserved:
Damages caused by not respecting these safety precautions are exempt from any
legal claim, regardless of their nature.
•Before using the device, you must read, understand and follow this manual.
•Before connecting the device to the power supply, check that the mains voltage
corresponds to the voltage established for the equipment.
•Do not place the equipment ondamp orwet surfaces.
•Do not cover the ventilation slots of the equipment to ensure that air can
circulate freely inside.
•Do not insert metal objects into the device through the ventilation slots.
•Do not place containers with water on the device (risk of short circuit if the
container spills).
•This equipment should not beleft running unattended.
•Follow the instructions that appear on the equipment screen.
•Do not expose the equipment to direct sunlight or extreme temperatures, damp
or wet places.
•Do not expose the equipment to strong shocks or vibrations.
•Do not work with the equipment near strong magnetic fields (motors,
transformers, etc.).
•Keep hot electrodes orwelders away from the equipment.
•Regularly clean the equipment with a soft, dry cloth. Do not use abrasives or
solvents.
•The equipment is suitable for indoor use only.
•Do not store the equipment ina place close to explosives orflammable
substances.
•Do not modify the equipment in any way.
•Do not place the equipment upside down onany table orworkbench toprevent
any damage tothe screen fromthe front.
•During valve tests, do not touch the valves to avoid entrapment due to moving
parts.
•The equipment's disassembly and repair should exclusively be performed by
qualified technical personnel from the Alfa e-Parts team.
•The equipment should be stored beyond the access of children.
4
v2.0
VALVE TESTER ALFA HT1
AF99999
2. Equipment cleaning
Note: Before cleaning the equipment, remove the plug from the outlet.
To clean the equipment you must take into account the following considerations:
•Clean only with a soft, dry cloth.
•Do not use abrasive products or solvents.
•Plastic parts, cables and stand can be cleaned with a mild household cleaner.
•The use of liquid products could damage the equipment if they get inside it.
5
v2.0
VALVE TESTER ALFA HT1
AF99999
3. Introduction
The valve tester is designed to verify the correct operation of EGR valves and throttle
valves. Electrical drive units and units with position sensor(s) can be tested.
Its operation consists of making a series of activations on the valve motor and capturing
the response of the sensor (or sensors) to compare it with the expected signal. The
expected signal consists of a margin (tolerance).
6
v2.0
VALVE TESTER ALFA HT1
AF99999
4. Technical data
Operating Voltage 80 ~ 264 VCA – Conversion to 12VCC (5A)
Screen type Projected capacitive multi-touch
Screen Size 7”
Resolution1200 x 600 pixel
Operating system Ubuntu
Dimensions 270cm x 20cm x 8cm
Weight 3Kg
CPU 2GHz Quad-core 64 bits (Amlogic S905X3)
Internal memory 16 GB eMMC
Ethernet
Wifi Yes
1000 Mbps
v2.0
VALVE TESTER ALFA HT1
AF99999
5. Equipment Composition
The equipment consists of the following elements:
•Touch screen tester
•Metallic support
•Tester power supply
•1.5 meter extension for test cables
•Test lead set
7
8
v2.0
VALVE TESTER ALFA HT1
AF99999
6. Operation
The tester consists of a plastic case and a touch screen that provides the control
interface for the operator.
1- Tester box
2- Touch screen
3- Ventilation grille
Note:
I
nthe sides of the box, wefind thetwoventilation grilles. It is important that these
are always uncovered to
prevent
overheating of the internal electronics ofthe tester.
2
1
3
VALVE TESTER ALFA HT1
AF99999
9
v2.0
At the back of the tester, all device connections and the main power switch are located.
1- Power connector
2- Network connector (RJ45)
3- Test cable connector
4- On/off switch
The equipment consists of a set of cables to adapt the tester to the different
connections incorporated by the valves to be tested. Each cable has a label located at
the end of the connector, indicating the identification number.
In addition, the equipment includes a 1.5m universal
extender to extend any of the cables that we must use.
1- Test lead set.
2- 1.5 meter extension cable for test cables.
3- Cable number identifier label.
1
2
3
1 2 3
4
VALVE TESTER ALFA HT1
AF99999
10
v2.0
The equipment includes a metallic support for the placement of the tester with an
ergonomic inclination, and two supports for the storage of the cables.
1- Tester base.
2- Support for test cables.
3- Housing for the power supply.
Through the side of the support
access is provided for the end of
each cable and the power supply
1
2
3
Tabla de contenidos
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
