Baxi Fires Division 742 Manual de usuario

5119074/01

OWNER GUIDE

This guide is intended to help you care for your gas fire. Please read thoroughly before

using and keep for future reference.

This guide to be left with the owner.

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

WHEN CONVERTED USING CONVERSION KIT NO. 0595211

THIS APPLIANCE IS FOR USE WITH PROPANE GAS (G31).

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

We trust that this guide gives sufficient details to enable your appliance to be operated

and maintained satisfactorily. However, if further information is required, our

Baxi Fires Division Technical Helpline will be pleased to help.

Please telephone 08706 061 065

(National call rates apply in the United Kingdom).

In the Republic of Ireland telephone 0044 8706 061 065

Model 742

REMOTE CONTROL

INSET LIVE FUEL EFFECT GAS FIRE

Fitted with the

Knightsbridge fascia.

(GC No. 32-264-21)

(including photocopying), stored in any medium by electronic means (including in any

retrieval system or database) or transmitted, in any form or by any means, whether

electronic, mechanical, recording or otherwise, without the prior written permission of

the copyright owner.

Applications for the copyright owner's permission to reproduce any part of this

publication should be made, giving details of the proposed use, to the following address:

The Company Secretary, Baxi Heating UK Limited, Pentagon House, Sir Frank Whittle

Road, Derby, DE21 4XA.

Warning: Any person who does any unauthorised act in relation to a copyright work

may be liable to criminal prosecution and civil claims for damages.

Baxi Fires Division, Erdington, Birmingham B24 9QP

www.firesandstoves.co.uk

Because our policy is one of constant development and improvement, details may vary slightly from those

given in this publication

Page 2

OWNER GUIDE

Safety First.

Baxi Fires Division fires are CE Approved and designed to meet the appropriate British

Standards and Safety Marks.

Quality and Excellence.

At the heart of every Baxi Fires Division fire.

All Baxi Fires Division fires are manufactured to the highest standards of quality and

excellence and are manufactured under a BS EN ISO 9001 quality system accepted by

the British Standards Institute.

The Highest Standards

Baxi Fires Division is a member of the Society of British Gas Industries which works to

ensure high standards of safety, quality and performance.

Careful Installation

Baxi Fires Division is a CORGI registered company. All our gas fires must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet or floor of combustible material.

Page 3

OWNER GUIDE

LIST OF CONTENTS

Section Page

SAFETY 5

GAS CONSUMPTION 6

APPLIANCE DIMENSIONS 7

OPERATING YOUR FIRE 8

The Oxysafe flame sensing & flue blockage safety system. 8

Lighting the pilot. 8

Heat settings. 9

To turn the fire back to pilot setting. 9

To turn the fire off. 9

Using the remote control handset. 9

CLEANING YOUR FIRE 10

Metal parts. 10

Ceramic fuel effect pieces and burner compartment walls. 10

Burner. 10

CERAMIC FUEL EFFECT REFITTING 11

MAINTENANCE 11

Regular maintenance. 11

Changing the batteries in the remote control receiver. 11

Changing the battery in the remote control handset. 12

Servicing. 12

USEFUL TELEPHONE NUMBERS 13

This gas fire is designed to meet the most stringent quality, performance and safety

requirements to provide you with many years’ trouble-free service.

This guide aims to improve your understanding and appreciation of your gas fire by

providing simple and informative instructions to ensure that you benefit from the

excellent performance and features it has to offer.

Page 4

OWNER GUIDE

SAFETY

Do have the fire installed by a competent person. In the United Kingdom, installation

must be in accordance with the latest edition of the Gas Safety (installation & use)

Regulations. In the Republic of Ireland, installation must be in accordance with all

national and local regulations in force.

have the chimney swept prior to installation if it was previously used for solid fuel.

Do have the fire installed in accordance with the installer guide.

provide a minimum clearance as shown in graph 1 above the base of the fireplace

opening to any shelf made of wood or other combustible material.

• For a shelf up to 150mm deep: Minimum height = 760mm.

• For a shelf deeper than 150mm: 760mm + 12.5mm for every 25mm depth over

150mm (See Graph 1).

Do provide a suitable guard that complies with BS 8423 for the protection of young

children, the elderly, the infirm and pet animals. (Although this fire conforms to all the

Page 5

OWNER GUIDE

Graph 1. Combustible shelf clearances.

IF YOU SMELL GAS

vDON’T SMOKE

vEXTINGUISH ALL NAKED FLAMES

vDON’T TURN ELECTRICAL SWITCHES ON OR OFF

vTURN OFF THE GAS SUPPLY AT THE METER

vOPEN DOORS AND WINDOWS TO GET RID OF THE GAS

IMMEDIATELY CALL THE GAS EMERGENCY SERVICE – SEE YOUR LOCAL TELEPHONE

DIRECTORY

applicable standards, it is a heating appliance and certain parts of its surface will

become hot).

Do wait three minutes before attempting to relight if the fire is switched off or the

flames are extinguished for any reason. (Your fire is fitted with a safety device that will

automatically shut off the gas supply to the fire if, for any reason, the flames go out).

Do get advice about the suitability of any wall covering near your fire. Soft wall

coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by

heat. They may, therefore, scorch or become discoloured when close to a heating

appliance. Please bear this in mind whenever you are considering redecorating.

provide a minimum side clearance as detailed in figure 1. Please bear this in mind if

ever you are considering altering the room.

Don’t hang clothing, towels or any other fabrics over the fire.

Don’t add any extra fuel effect pieces above the number stated in the guide supplied

with the ceramics. This could cause a safety hazard.

Don’t put paper or any other material on the fire.

Don’t place any combustible material (rugs, carpet, plastic tiles, etc.) on the hearth.

Don’t

attempt to clean or service the fire until it has been switched off and allowed to

cool completely.

GAS CONSUMPTION

Model 742

Has a maximum natural gas input of 6.8kW (Gross)

Has a maximum natural gas output of 3.5kW

Has a minimum natural gas input of 1.7kW (Gross)

Has a minimum natural gas output of 0.70kW

Model 742 when converted using kit number 0595211

Has a maximum propane gas input of 6.7kW (Gross)

Has a maximum propane gas output of 3.7kW

Has a minimum propane gas input of 3.2kW (Gross)

Has a minimum propane gas output of 1.7kW

Page 6

OWNER GUIDE

APPLIANCE DIMENSIONS

Page 7

OWNER GUIDE

Key

AB C DE

Model Height

(mm) Width

(mm)

Depth

into

room

(mm)

Minimum

mandatory

clearance to

combustible

surfaces projecting

beyond the front of

appliance (mm).

Recommended

clearance to non-

combustible

surfaces

for access purposes

(mm).

knightsbridge 599 492 65 125 10

Figure 1. Appliance dimensions and clearances (Dimensions are subject to

manufacturing deviation. Fascia may differ from that shown).

OPERATING YOUR FIRE

The Oxysafe flame sensing & flue blockage safety system.

For your safety, this appliance is fitted with a flue blockage safety device which will

shut down the appliance in the event of abnormal flue conditions.

This device is NOT a

substitute for an independently mounted Carbon Monoxide detector.

The device will also automatically shut off the gas supply to the fire if the pilot flame

goes out due to lack of oxygen or for any other reason.

If this device starts to repeatedly shut off the gas, get expert advice.

This device incorporates a probe which senses that the heat from the pilot flame is

correct. If this probe is cool, the device will prevent any gas flow unless the control

knob is held in at the ignition position.

If, for any reason, the flames go out when the fire is hot or if the fire is turned off when

hot, always wait at least three minutes before attempting to relight.

vThis fire may be controlled manually, by use of the controls mounted on the

appliance. The flame settings may also be controlled by means of the remote control

handset.

Lighting the pilot.

Please note: The fire must be

lit manually.

1. Ensure that the pilot burner

control knob is in the OFF

position (Number 1 in figure

2).

2. Depress the pilot burner

control knob and turn anti-

clockwise to the ignition

position (Number 2 in figure 2)

to activate the piezo ignition

system. A 'click' will be heard

Page 8

OWNER GUIDE

PLEASE NOTE

When operating your fire for the first time, some vapours may be given off which may

cause a slight odour and could possibly set off any smoke alarms in the immediate

vicinity. These vapours are quite normal with new appliances. They are totally harmless

and will disappear after a few hours use.

Figure 2. Appliance manual controls.

and the pilot should light. Observe if it is alight by looking through the slots to the left

hand end of the front coals. If the pilot does not light immediately, repeat the above

procedure, keeping the knob depressed for several seconds in order to purge any air

from the system.

If after ten seconds, ignition has not occurred, turn the control knob back to the OFF

position. Wait 30 seconds and then repeat the ignition procedure.

3. When the pilot is alight keep the knob depressed for ten seconds to allow the pilot

flame to stabilise.

4. Release the knob. When the knob is released, the pilot should remain alight. If the

pilot fails to remain alight, repeat the ignition procedure, this time keeping the knob

depressed for a longer period of time.

Heat settings.

Once the pilot light is established, light the main burner by turning the pilot burner

control knob anti-clockwise to the "main burner on" position (Number 3 in figure 2),

and by then turning the main burner control knob to the high position (Number 5 in

figure 2).

Check the full range of heat settings by turning the main burner control knob slowly

between the high position and the low position (Number 4 in figure 2).

To turn the fire back to pilot setting.

Turn the main burner control knob fully clockwise. Alternatively turn the pilot burner

control knob clockwise to the ignition position (2). Refer to figure 2.

To turn the fire off.

Rotate the pilot/burner control knob clockwise to position 1, as shown in figure 2.

Using the remote control handset.

Keep the pilot burner at the "main burner on" position. Check the full range of main

burner heat settings using the remote control handset. In order to vary the flame effect

between High and Low positions, press, and keep depressed, either the High button, or

the Low button as appropriate (See figure 3).

The handset operates on

ultrasonic principles, and as

such it is not necessary to point

it directly at the fire.

2. Use the handset to switch to

the pilot only setting by

depressing the Low button until

only the pilot flame remains

alight.

3. In order to disable the

Page 9

OWNER GUIDE

Figure 3. Remote control handset.

handset, but still leave the pilot alight, turn the pilot burner control knob to the ignition

position (Number 2 in figure 2).

4. Turn the fire off by rotating the pilot burner control knob to the OFF position

(Number 1 in figure 2).

CLEANING YOUR FIRE

To maintain the high performance and quality finish of your fire please follow these

guidelines:

Before attempting to clean the fire, please remember to turn off the fire and wait for the

appliance to cool. The fire will retain heat for some time before cleaning can begin.

If any pieces of debris are found in the firebox, have the chimney inspected before

further use.

Metal parts.

! Clean the metal parts with a slightly damp cloth and then dry.

! Do not use abrasive cleaners as these will scratch the fire surface.

Clean the metal parts with a slightly damp cloth and then dry. If this does not work

apply a very small amount of ‘baby oil’ to a lint free, non-abrasive cloth and wipe over

the surface. Use a clean cloth to wipe off the oil.

Ceramic fuel effect pieces and burner compartment walls.

This product uses fuel effect pieces and burner compartment walls containing

Refractory Ceramic Fibres (RCF), which are man-made vitreous silicate fibres.

Excessive exposure to this material may cause irritation to eyes, skin and

respiratory tract. Consequently, it is important to take care when handling these

articles to ensure that the release of dust is kept to a minimum.

Light coatings of soot will usually be burnt off during the normal operation of the

fire. Should any soot accumulation become excessive, the fuel effect pieces and walls

should be removed from the fire for cleaning.

Cleaning should be carried out in a well ventilated area or in the open air by gently

brushing with the pieces held away from your face so that you avoid inhaling the

dust.

! We do not recommend the use of a normal domestic vacuum cleaner which may

blow dust back into the air.

! We suggest that you remove the ceramic fuel effect pieces in the reverse order to

that shown in the fuel bed refitting instructions.

Burner.

Remove any deposits of soot or other foreign matter from the surface of the burner with

a dry soft brush. Be careful not to brush any particles into the open slots. Remove any

particles from the slots with a vacuum cleaner fitted with a soft brush attachment. Do

not poke wire, etc. into the slots in the burner.

Page 10

OWNER GUIDE

Otros manuales para 742

Tabla de contenidos

Otros manuales de Chimenea de interior de Baxi Fires Division

Baxi Fires Division

Baxi Fires Division 756 Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division 750 Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division 949 Manual de usuario

Baxi Fires Division

Baxi Fires Division 341 Black Beauty Slimline Manual de usuario

Baxi Fires Division

Baxi Fires Division 754 Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division 750 Manual de usuario

Baxi Fires Division

Baxi Fires Division 755 Manual de usuario

Baxi Fires Division

Baxi Fires Division Soraya 746 Manual de usuario

Baxi Fires Division

Baxi Fires Division 941 Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division Heartbeat Oxysafe 2 Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division Dream BR660VA Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division Sonnet Plus Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division 347 Manual de usuario

Baxi Fires Division

Baxi Fires Division 742 Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division 750 Manual de usuario

Baxi Fires Division

Baxi Fires Division 347 BLACK BEAUTY Manual de usuario

Baxi Fires Division

Baxi Fires Division 759 Manual de usuario

Baxi Fires Division

Baxi Fires Division 739 Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division 740FS Manual de usuario

Baxi Fires Division

Baxi Fires Division 939 Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division 754 Manual de usuario

Baxi Fires Division

Baxi Fires Division 956 Instrucciones de montaje

Baxi Fires Division

Baxi Fires Division soraya 747 Manual de usuario

Baxi Fires Division

Baxi Fires Division 740FS Instrucciones de montaje

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación