Baton EVPOS-1TACA Manual de operación

Owner's Operating Manual

EVPOS-1TACA Welding Positioner

Chapter 1: Introduction

Objective

Restriction of the work piece

1.1.1 The POS for MCA series positioner can be used welded, cut and grind, it has one table rotate and table angle move, the operator can be apt to

adjust the work piece position fast, enable him to finish the work and keep quality fast.

1.1.2.1 The weight or length of the work piece exceed designing limiting, please look at charts [Figure:1.2-1].

1.1.2 Forbid using the case:

1.1.2.2 The work piece does not have certain locking in table of EVPOS for MCA series positioner.

1.1.2.3 The scope of activities of the work piece has personnel or hinders things.

1.1.2.4 Have not imputed the machine to the ground or firm foundation.

Figure: 1.2-2

1.1

1.2

1.2.1 CAPABILITY

Page 1

200

400

600

800

1000

1200

1400

1600

020 40 60 80 100 120 140

200

400

600

800

1000

1200

30 40 50 60 70 80 90 100

EVPOS-1TACA Positioner Eccentric Load

A : Eccentric Center (cm.)

W : Load (kg.)

EVPOS-1TACA Center of Gravity

B : Center of Gravity (cm.)

W : Load (kg.)

Structure

1.3

1.3.1 Specification

1.3.2 Standard Accessories 1.3.3 POS for ACA series Structure

Figure: 1.3-1 Figure: 1.3-2

Part Name Quantity

Pedal Switch 1

Welder start wire 1

Table

Controller

Angle limit switch adjustment unit

Rotation gearbox of table

Angle labelling

Page 2

Specification

Power

Table rotate motor

Capacity

Eccentricity

Center of Gravity

Table Dia.

Spindle Thru Hole

Table speed

Table angle

Table angle speed

Table angle motor

Table angle lock

Table rotate control

OverLap timer(Fixing point)

Timer (Fixing point)

Lap well timer (Fixing point)

Start / Crater arc timer

Arc way of the welder

Welding current

Table rotate control

Remote control

EVPOS-1TACA

V1:AC 220V / 20A / 50;60Hz / 3Ø

V2:AC 380V / 18A / 50Hz / 3Ø

DC 180V / 400W

1000Kg.

300mm.

900mm.

120mm.

0.05-0.5 RPM

0° - 135°

55!sec / 135°

AC 0.5HP

Motor brake

inch / Hold / Overlap / Timer

0 - 99.9sec(display unit : 0.1sec)

0 - 999sec(display unit :1sec)

0 - 99.9sec(display unit : 0.1sec)

Standard(2 cycle) / Cater(4 cycle)

1000A / 100%

Pedal switch(The wire is 4M Cable)

Control line(The wire is 4M Cable)

peci

ication

Chapter 2: Safety

Safty Information

2.1.1 This document provides general safety instructions. Some information requires special attention for either safety or procedural reasons. Label with an appropriate heading WARNING and

CAUTION will be used throughout this manual. For example:

2.1.1.1 Failure to follow WARNING instruction could result in severe injury or death to the operator, a bystander or a person inspecting or repairing the machine.

2.1.1.3 Failure to follow DANGER instruction could result in severe injury or death to the operator, a bystander or a person inspecting or repairing the machine.

2.1.1.2 Failure to follow CAUTION instruction may result in injury to the operator, a bystander or a person inspecting or repairing the machine, or damage to the machine’s part and/or controller.

2.1.1.4 Failure to follow ATTENTION instruction may result in injury to the operator, a bystander or a person inspecting or repairing the machine, or damage to the machine’s part and/or controller.

WARNING

ATTENTION

2.1 Page 3