Bastl TEA KICK Manual de usuario

TEA KICK v1.0 Brief Assembly guide



This is a brief guide

for more advanced

users. If you are a

beginner please look

for the detailed guide

on our website.

Start by populating

and soldering the

boards with the

shortest and smallest

parts. Taking care of

the values, polarity

and alignment of the components.

Note: The crossed out resistor value at the lower part of the board is 1M.

Note: The protective fuses look quite similar to ceramic capacitors but are placed in the

blank rectangular markings on the board.

To ensure that all the connectors are properly aligned, solder them with the two boards

connected and screwed together. The same goes for the UI components, solder them with

the front panel secured in place.

The finished bottom board should look like the one to the left.

The LED long leg (+) is facing upwards. Also the notch on

led and circuit board should match.

Note: the LED and Switch have to be raised a bit off the

PCB in order to reach through the front panel.

The assembled top board should look like on the images to

the left.

Before connecting anything, make sure that your system is

disconnected from power and double check the polarity of

the ribbon cable, the red cable should match the -12V rail

both on the module and on the bus board!

Bill of Materials

2 x 10k resistors

1 x 68n capacitor

1 x TL74 IC

11 x 100k resistors

2 x 6,8n capacitor

1 x Switch

2 x 1M5 resistors

5 x 1N4148 diodes

2 x 100mA fuses

4 x 1k resistors

2 x 1N4007 diodes

1 x diffused green LED

1x 1M resistor

6 x jack connectors

1 x 14 pin DIL socket

1 x 220 resistor

1 x 2N3904 transistor

1x 8 pin DIL socket

1x 22k resistor

1 x 10k linear pots

1 x 2x8 Ribbon cable

1 x 2M2 resistor

1 x 50k linear pots

4 x Knobs

3 x 2k2 resistors

2 x 100k linear pots

2 x PCBs

1 x 47k resistor

1 x 50k trim pot

1 x Wooden panel

4 x 100uF electrolytic capacitors

1 x 2x8 male pin header

6 x Jack washer and nuts

9 x 100nF ceramic capacitor

1 x 18 male pin header

2 x Hex screws

1 x 10n capacitor

1 x 18 female pin header

2 x Phillips screws

1 x 2,2u electrolytic capacitor

1 x TL72 IC

1 x hex spacer nut

1 x hex spacer nut - screw



Tabla de contenidos

Otros manuales de Equipo de grabación de Bastl

Bastl

Bastl Popcorn Manual de usuario

Bastl

Bastl Propust Manual de usuario

Bastl

Bastl CASPER SOFTPOP SP2 Manual de usuario

Bastl

Bastl CASPER SOFTPOP SP2 Manual de usuario

Bastl

Bastl Kastle ARP Manual de usuario

Bastl

Bastl tromso Manual de usuario

Bastl

Bastl BESTIE Manual de usuario

Bastl

Bastl microGranny Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado