BassBoss AT312-MK3 Manual de usuario

3-Way 12”

Powered Top

AT312-MK3

User Manual

AT312-MK3 User Manual bassboss.com

Table of Contents

Overview 2

QuickStartGuide 4

OutboardProcessorWarning 5

SetupProcedure 5

OperationandControls 6

IndicatorLEDs 6

HowtoUsethePresets 7

Pre-InstalledOnboardPresets 8

PowerDistribution 9

Troubleshooting 9

Specifications 10

Warranty 11

SafetyInformation 12

FCCComplianceNotice 13

The12” co-axial mid-highsectionallows theloudspeakerto function asapoint-source,with thetwoadditional low-

frequencydriversremainingwithin½wavelengthintheiroperatingband.Thisarrangementdeliversmoreconsistent

o-axisperformancethanconventionalloudspeakers.Theconsistencyofcoverageandtheuniformityoftheresponse

throughout the coverage area make the AT312-MK3 highly resistant to feedback. The coverage consistency also

enhances the loudspeaker’s versatility, allowing it to be mounted horizontally or vertically with no compromise in

coverageorperformance.*

This allows the AT312-MK3 to be flown horizontally in venues with low ceilings or on truss that wouldn’t provide

enoughheightforverticallyorientedcabinetsorline-arrays.Thepoint-sourcecoherenceoftheAT312-MK3provides

outstandingintelligibility.AsingleAT312-MK3canbeusedinplaceofanarrayoflesscoherentspeakersandprovide

superiorintelligibility.

WhentheAT312-MK3iscombinedwithBASSBOSSsubwoofers,liketheSSP218,SSP215orZV28,theresultisa4-way

activeloudspeakersystemwithvirtuallyunparalleledresolutionanddynamicpowerforitssize.

The simplicity and ease of using these components together will delight anyone who is regularly moving gear.

Transportationandset-upofanAT312-MK3/SSP218-MK3orSSP215-MK3Subwoofercombinationismadeeasybecause

thesubwoofersserveasacarrierforthetops.The48”tallcabinetelevatesthemidandhighfrequencyradiatorstoa

minimumof7’6”oncenterwhenstackedonthesubwoofers.Thisveryeective,practical,highfidelityactiveloudspeaker

systemcanbemadereadytoplayinafewshortminutes.Inmostvenuesit’spossibletorollthesystemintoplace,lock

thecasters,tiltupthetops,pluginthepowerandsignalandhaveanextremelysubstantialsystemsetupbyjustone

person.

*Anyspeakerthathasthetweeterhorizontallyorverticallyosetfromthemid-frequencydriverwilltendtoproduce

very dierentfrequencyresponse asonemovesthrough itscoverageareafromthe tweeterside tothewoofer side.

Thisisduetothedierentdistancesthesoundhastotraveltoreachtheears.Duetotheco-axialconstructionofthe

AT312-MK3,thepathlengthdierencebetweenlows,midsandhighsisthesameinanydirection,allowingextremely

consistento-axisresponseregardlessofwhichdirectionyoumoveawayfromdirectlyoncenter.

TheAT312-MK3features4000Wofamplification.With2400Wofofitspoweravailableforthewoofers,800Wavailable

tothemidrangeand800Wavailabletothetweeter,powerisplentiful.Theamp’shighpeak-outputvoltageprovidesfor

veryintense,highSPLhits.

Anauto-sensing,globallycompatiblepowersupplythatcanrunoninputvoltagesanywherebetween90and250Volts

ensureitcanworkwhereveryoutakeit.Fulloutputpowerisavailableonanythingover110V.Theamplifierispassively

cooledviaitsexternalheat-sinkandbywoofer-generatedair-flowthroughtheport.Whennecessary,twoblower-fans

willengagetoprovideadditionalforced-aircoolingcapacityinmoreextremeconditions.

Amplifierpowerisconvertedintothemuchmoredesirableacousticalpowerbytwosubstantial,neodymiummotor,12-

inchwooferswith4-inch(100mm)voicecoils,a12”neodymiummotormidrangedriverwitha3.5”(88mm)voicecoiland,

onthesameneodymiummotor,acompressiondriverwitha3”(76mm)voicecoilthatexitsthroughthecenterofthe

midrange,whichfeaturesa1.4”throatmachinedaluminumconicalwave-guideasitspole-piece.

Neodymiummagnetsarelighter,andtheirhigherintensityprovideshighereiciency,sotheresultisalighterandlouder

cabinetthanthosewithferritedrivers.Itsdrivercomplementincorporatesdual12-inchwoofersinaventedenclosurefor

lowfrequenciesanda12-inchmidrangedriverinasealedenclosurewithaco-axiallymounted1.4-inchexitcompression

driver.Coverageis80degreesconical.Dual12-inchlowfrequencydriverswerechosentominimizecabinetfrontalarea

whiledeliveringthebestpossiblespeedandimpactintheiroperatingrange.Thankstothenarrowfrontalarea,thelow

frequency driverscouplecoherentlywhenmultiple cabinets arearrayed,providingpowerfulmid-bass impactfroma

small,lightweightbox.The12-inchcoaxialdriversalsoservetominimizefrontalareawhilemaximizingoutput.The48

inchtallboxelevatesthemidandhighfrequencyradiatorstoaminimumof7feet6inchesoncenterwhenstackedon

thecorrespondingsubwoofersystems.

Overview

TheAT312-MK3Topisaco-axialpoint-sourcecabinetformediumandshortdistancecoveragewhereasmallfootprint

andveryhighfidelityarerequired.It’scompact,simpletouse,easytosetup,attractiveandcapableofveryhighoutput

withsuperblyuncoloredsoundandnaturalmusicalcharacter.

TheAT312-MK3drivercomplementincorporatesdual12”woofersinaventedenclosureforlowfrequencies,a12”driver

ina sealed enclosureproviding midrange, withaco-axially mounted1.4” exit compression driverprovidingthe high

frequencies.Coverageis80degreesconical.

Dual12”lowfrequencydriverswerechosentominimizecabinetfrontalareawhiledeliveringthebestpossiblespeedand

impactintheiroperatingrange.Thankstothenarrowfrontalarea,theAT312-MK3canprovidetremendousoutputand

fidelitywhileremainingrelativelyunobtrusive.

AT312-MK3 3-Way 12”

Powered Top

Estemanualestádisponibleenespañolennuestrositiowebenbassboss.com/support

AT312-MK3 User Manual bassboss.com

Outboard Processing Warning

Third-party outboard processing (Drive Racks, etc.) are not recommended and are not necessary

with BASSBOSS MK3 series powered loudspeakers. Outboard processing will not improve, and

will very likely degrade the sound quality, reliability and output capacity. Using external processing

inappropriately can cause driver damage that is not covered by warranty.

The internal processing can accomplish everything an external processor could accomplish without

degrading the sound quality and without putting components at risk. Before considering using an

outboard processor, contact BASSBOSS customer service with your use-case scenario for assistance

in setting up the internal processing to achieve your goals.

Setup Procedure

Once the the cabinet is in the desired location, signal cables should be connected via the XLR-F input.

It’s recommended to run balanced signal cables to minimize the chance of noise and ground-loop hum.

The incoming signal should be unprocessed because all the necessary processing is done in the built-

in DSP. The signal should be run directly from the outputs of a mixer or controller.

The XLR-M connector provides a full-range, unprocessed, pass-through connection to additional

cabinets. This output can be connected to additional subs or tops. Up to 12 cabinets can be connected

on a single output from a mixer or controller.

Connecting the mains power. The power connector is a Neutrik PowerCON TOP waterproof type. The

power connector inserts with the silver tab rotated counter clockwise from vertical, at about the 10:00

position, and once inserted, rotates clockwise to the 12:00 position to lock in place. Once locked, this

connector is waterproof.

This connector also serves as the power switch. To disconnect and remove the connector, pull back

on the silver tab to unlock it and rotate it counter clockwise. Once rotated to the insertion angle, the

connector can be removed.

When connecting and disconnecting, no force should need to be applied. If the connector doesn’t

insert and rotate smoothly, either it’s in the wrong position or it’s damaged and should be replaced.

Always use a grounded outlet. The supplied power cord includes a standard grounding NEMA 5-15

(Edison) 120-Volt US wall plug. In unfamiliar locations it’s recommended to verify the correct wiring of

outlets before powering your system.

It’s highly recommended to connect all signal and power cords to the speakers before plugging the

power cords into mains outlets. When your speaker is powered on, you’ll see all the indicator lights turn

on and then show the system’s current status.

Although the AT312 cabinet is equipped with a 35mm steel pole socket, DO NOT use this speaker on a

tripod or extension pole. This socket is to be used with a special, short section of pole to prevent it from

moving once stacked on a subwoofer.

Quick Start Guide

1. Ensure the cabinet is secure and stable.

2. Connect signal via the XLR-F input.

3. Connect the XLR-M connector to additional subs or tops.

4. Connect the mains power and verify the “Ready” LED is lit.

BASSBOSS systems are easy to set up quickly. The best possible results are achieved consistently

because of the integrated nature of the designs. All BASSBOSS loudspeakers are complete, integrated

systems, featuring the cabinet, transducer, amplifier and a comprehensive suite of processing. Setup

is particularly easy because the products integrate with each other.

Provided the cabinets are physically aligned, any BASSBOSS sub can be combined with any

BASSBOSS top and their outputs will be phase-coherent. This means no cancellations and no gaps in

the response at the crossover frequency, regardless of which preset is selected.

The on-board BASSBOSS processing allows for the following:

Any BASSBOSS powered subwoofer can be combined with any other BASSBOSS Powered subwoofer

and their outputs will sum coherently. (i.e.: in phase with each other.)

Any BASSBOSS powered subwoofer or combination of BASSBOSS powered subwoofers can be

combined with any BASSBOSS powered top and their outputs will sum coherently through the

crossover region.

HOWEVER only one model of top should be used at a time. An assortment of dierent tops cannot be

stacked together and still achieve coherence and clarity.

The following tops should be used individually, i.e. should NOT be arrayed:

AT312 (Co-axial point-source Main)

DiaMon (Co-axial point-source satellite)

SV9 (2-way monitor with Satellite mode)

The following tops can be used in arrays:

MFLA (Medium Format Line Array, up to 20 cabinets can be arrayed)

AT212 (Horizontally arrayable when necessary)

DV12 (Arrayable in PAIRS ONLY with the upper box of the pair inverted.)

AT312-MK3 User Manual bassboss.com

How to Use the Presets

Setting the low-pass filter frequency on the subwoofer to match the top cabinet’s high-pass filter

frequency and balancing their levels will achieve the smoothest sound across the frequency range.

There are no incompatible combinations.

Selecting high numbered presets on subs with low-numbered presets on tops will result in increased

system output in the overlap range, which can be helpful in some situations but can also result in a

“boomy” sound.

When the subwoofer levels are to be run higher than tops levels, (which is almost always) the eective

crossover moves higher in frequency. If you intend to run your system “bass-heavy” it’s recommended

to run lower-numbered presets on the subs and higher-numbered presets on the tops to avoid an

excessively “boomy” sound.

Selecting low-numbered presets on subs with high-numbered presets on tops may result in a lack

of “punch” in certain combinations. This is most likely when not enough level is available from

the subwoofer(s).

When not enough output is available from the sub(s), using a preset combination with overlap can help

provide a little more bass level but it does limit the maximum level of the tops due to the added demand for

low-frequencies from the tops.

It’s recommended that you try several, if not all, combinations when first setting up to determine which

combination works best in each environment. You will likely choose dierent combinations for wood

floors, concrete floors and outdoors.

Experiment with dierent combinations to dial in your preferred combination in dierent environments.

Operation & Controls

There are 2 controls on the amplifier.

1: Input

This knob adjusts the input level from -72dB to -0dB. To avoid distortion and clipping, make sure the

input signal doesn’t exceed +22dB and the output doesn’t reach clipping before you achieve the desired

sound level.

While the amplifier has built-in limiters and safety features to protect itself and the speaker, it can’t

protect the speaker from distorted incoming signals. The amplifier will simply amplify the clipped signal,

which can do the same damage as clipping an amplifier. Since it’s essentially impossible for these

amplifiers to clip, signal-level clipping is the most common cause of damage to these speakers.

If you hear distortion, lower the input level right away.

2: Preset Select

Pressing the Preset Select button cycles through presets 1-8, and pressing it again after preset 8 returns

to preset 1. Each preset includes all necessary low-pass and high-pass filters at the selected frequencies

and all the necessary alignments to maintain phase coherence in the crossover range when used with

other BASSBOSS powered speakers.

Presets help you fine-tune the balance between the subwoofers and top speakers. More details on the

dierent combinations are on page 7.

Indicator LEDs

Indicator LEDs – Left side, bottom to top:

Ready: Indicates that power is on and the system is ready to play.

Signal: Indicates the presence of input signal.

-12dB: Indicates there is 12dB of headroom remaining before reaching maximum output.

-6dB: Indicates there is 6dB of headroom remaining before reaching maximum output.

Limiting: Indicates one of the channels is reducing the incoming signal level to prevent overdrive.

Overheat: Indicates the amplifier is reducing output to prevent shut-down from overheating.

Protect: Indicates the amplifier is shut down due to a condition that could cause further damage.

The Protect LED also is engaged when the system has been muted via the software.

Comm Link: Indicates communication is active on the LAN connection(s).

Indicator LEDs, Right Side, Bottom to top:

Presets 1-8 - The illuminated LED indicates the corresponding preset is loaded.

AT312-MK3 User Manual bassboss.com

Power Distribution

Connect no more than one 5000W or two 2500W subwoofer amplifiers to a single 20A circuit. If you

need to share circuits don’t exceed two BASSBOSS single-driver subwoofers or one double-driver

subwoofer along with one or two top speakers on the same circuit.

Although amplifiers for tops and subs may be specified to have the same power capacity, amplifiers

used for tops applications tend to draw significantly less current. Subwoofers draw far more current

than tops due to the demands for level and the duration of the notes.

The amplifiers can operate on mains supply from 100 to 250VAC. To connect to voltages other than

120V, a dierent mains connector plug must be used. Contact your salesperson for information about

purchasing cables for alternate voltages.

Pass-through Power connections can be used to power additional cabinets. With optional True 1 TOP

cables, power can be linked between subs and tops. Do not connect equipment that will draw more than

15A on a single power outlet. Contact your salesperson for information about linking power cables.

Avoid powering all subwoofers on the same circuit. Instead, use separate circuits for each subwoofer

and top speaker combo to help prevent overloading a single circuit and tripping a breaker.

Troubleshooting

If, after following the previous instructions for setup, you have no output from the loudspeaker:

Verify that the green Ready LED is lit. If NOT lit, check the following:

1. Is the power cord plugged into a live outlet?

2. Is the Neutrik powerCON connector rotated into the locked position?

If the green Ready LED is lit, check the following:

1. Is the red Protect LED illuminated? The unit may be in protect mode or set into mute via software.

2. Is the signal cable connected to the input?

3. Is the signal cable connected to an operating output at the other end?

4. Is there signal flowing to the input? Check the integrity of the cable against a dierent cable.

5. Is the volume knob turned all the way down or at a very low level?

6. Is the signal flowing to the input full-range?

Filters in the signal may remove the operating frequencies of the loudspeaker receiving them.

7. If you’re connected via LAN, check the level and filter settings in the software.

Pre-Installed Onboard Presets

High-pass filters with included phase compensation.

Preset 1: 60Hz Butterworth 24dB/octave high-pass filter

Preset 2: 60Hz Linkwitz-Riley 24dB/octave high-pass filter

Preset 3: 70Hz Butterworth 24dB/octave high-pass filter

Preset 4: 70Hz Linkwitz-Riley 24dB/octave high-pass filter

Preset 5: 80Hz Butterworth 24dB/octave high-pass filter

Preset 6: 80Hz Linkwitz-Riley 24dB/octave high-pass filter

Preset 7: 90Hz Butterworth 24dB/octave high-pass filter

Preset 8: 90Hz Linkwitz-Riley 24dB/octave high-pass filter

Additional presets are accessible through software. See “How to Use the Presets” section

for more information. Additional presets will be available for download at the above link as

they are developed.

Instructions on linking to your computer for remote monitoring and control:

www.bassboss.com/software

To be notified when new presets are released register your gear at: www.bassboss.com/support

AT312-MK3 User Manual bassboss.com

Speciﬁcations

Acoustical

LoudspeakerDescription: High-Output3-WayPoint-sourceloudspeaker

FrequencyResponse(±3dB): 60–19,000Hz

MaximumSPL: 133dB

PeakSPL:* 139dB

NominalDispersion(°Hx°V): 80x80

Electrical

Amplification: 3600WattFour-ChannelClassDAmplifier

Processing: IntegratedcomprehensiveDSPwith8localpresets(Additionalpresetsaccessiblevia

software)

ElectricalConnectors,Amplifier: NeutrikPowerconTrue1TOPinandthrough

ElectricalConnector,Mains: NEMA5-15(Edison)

VoltageOperatingRange: 100-240V.Auto-sensing,autoswitchinguniversalsupply

CurrentDraw,Nominal: 5@120volts,2.5A@220V(typical,1/8maxpower)

Display: LEDsforPoweron/ready,Signal,-12dB,-6dB,limiteractive,Thermal,ProtectandLANlink

active.EightLEDsindicatingselectedpreset

SignalInputConnector: XLR-F

SignalOutputConnector: XLR-Mpass-through

LANConnectors: EtherCONRJ45(x2)

Physical

EnclosureType: Self-powered,Tri-amplified,3-waybroad-range.DirectradiatingventedLFsection,Sealed

 Midrangesection,Co-AxiallyMountedHorn-loadedHFsection

Transducer,LF: 2x12”diameter(300mm)Neodymiummotorwooferwith4”(100mm)voicecoils

Transducer,MF: 1x12”diameter(300mm)Neodymiummotordriverwith3.5”voicecoil

Transducer,HF: 1x1.4”throatNeodymiummotorcompressiondriverwith3”(76mm)voicecoilexitingthrough

an80-degreeconicalmachinedaluminumwaveguideinthecenterofthemidrangedriver

CabinetConstruction: 18mm13-plyBirchplywoodwithextensiveinternalbracinganddamping.

Includes6integratedhandlesandasteel35mmpolesocket

SuspensionPoints: 4xinternallybracedM10threadedmountingpoints

Dimensions(HxWxD): 48”x16”x20”(122cmx40.6cmx50.8cm)

NetWeight: 126lbs.(57kg)

ShippingWeight: 140lbs.(63.5kg)

ExteriorFinish: Rugged,weatherproof,black,textured,bondedhigh-pressurepolyureacoating

Grille: Perforated,powdercoatedsteel

Optional

SidePullAnchors: Forusewhenflyingcabinetshorizontally

ShoulderEyeBolts: Forusewhenflyingcabinetsvertically

Cover: Heavy-dutypaddednylontransportcover

OnlineInformation: bassboss.com/at312

*Peakoutputiscalculated using“industrystandard”techniques.Thesecalculationmethodscreatetheoreticalspecifications

that are inflated over what can actually be achieved. BASSBOSS real world output specifications are provided as

“MaximumSPL”ratings,whichreflectactualmeasuredoutputlevels.

Our proactive philosophy causes specifications to be subject to change whenever improvements are made.

Warranty

WARRANTY INFORMATION | Our fully-transferable warranty covers all BASSBOSS products.

STANDARD CABINET WARRANTY

BASSBOSS loudspeaker cabinet integrity, including all joinery, fasteners, handles and wood, is

warranted against defects in materials and workmanship for a period of six (6) years from the date of

purchase. This warranty does not cover items that are intended to wear and can be replaced if worn

or damaged. Examples of items not covered by this warranty are cabinet feet, grilles and the finish or

coating applied to the cabinet.

ENHANCED COMPONENT WARRANTY

BASSBOSS amplifiers and electronic components are covered against failures due to defects in

materials and/or workmanship for a period of three (3) years from the date of purchase.

TRANSDUCER WARRANTY

Transducers are covered against failures due to defects in materials and/or workmanship for two (2)

years from the date of purchase.

OUR SUPPORT

Warranty support is a service, and part of that service includes helping you prevent failures and

minimize repair and shipping costs.

Please do not ship products without obtaining a return authorization number (RMA) by contacting

BASSBOSS at bassboss.com/support. If you need to ship your speaker for service, BASSBOSS

technicians will provide assistance on shipping and packaging requirements specific to your

service needs.

WARRANTY LIMITATIONS

During the warranty period, if your loudspeaker malfunctions or fails due to any defect in components

or manufacturing, the failed parts will be repaired or replaced. This warranty does not extend to damage

resulting from improper installation, misuse, neglect or abuse. Warranty coverage and eligibility will be

determined upon inspection by BASSBOSS personnel. This warranty does not cover labor other than

that authorized and performed by BASSBOSS personnel. Service will be performed upon the return of

the failed unit, together with its original sales receipt or other proof of purchase, to BASSBOSS or an

Authorized Service Facility. Purchaser is responsible for all costs of shipping and handling. Cosmetic

damage is specifically excluded from this warranty. This warranty is rendered void if service, repairs

and/or modifications are attempted or made by anyone not specifically authorized by BASSBOSS to

perform said services. Please contact BASSBOSS or your local BASSBOSS dealer before attempting

any repairs and before shipping parts in for service. This warranty gives you specific legal rights, and

you may also have other rights, which vary from state to state.

AT312-MK3 User Manual bassboss.com

Safety Information

Important information regarding safety and the use of your loudspeakers:

To prevent potentially dangerous exposure to high levels of acoustic pressure, never stand in the

immediate vicinity of loudspeakers driven at a high level without hearing protection. Professional

loudspeaker systems are capable of causing sound pressure levels detrimental to human health.

When a transducer capable of producing high sound levels is being used, it is necessary to wear

ear plugs or protective earphones to prevent hearing damage.

Even seemingly non-critical sound levels (from approximately 95 dB SPL) can cause hearing

damage if people are exposed to it over a long period. Anyone exposed to these levels should use

appropriate hearing protection devices. System and venue owners and operators are encouraged

to make hearing protection devices available to all customers and sta members.

In order to prevent accidents when setting up the loudspeakers or loudspeaker stands, make sure

they are standing on a firm surface. Ensure that all additional hardware, fixings and fasteners used for

installation or mobile deployment are of an appropriate size and load safety factor.

Always use the included, factory installed, internally secured M10 fly points when supporting the

cabinets. Use appropriately load-rated hardware. Never hang loudspeakers from handles. Never drill or

screw into cabinets to attach lifting points.

Pay attention to the manufacturers’ instructions and to the relevant safety guidelines. Regularly check

the loudspeaker housings and accessories for visible signs of wear and tear, and replace them when

necessary. Regularly check all load bearing bolts in the mounting devices.

Caution: Loudspeakers produce a static magnetic field even if they are not connected or are not

in use. Therefore make sure when erecting and transporting loudspeakers that they are nowhere

near equipment and objects which may be impaired or damaged by an external magnetic field.

A distance of 3 feet (1m) should be maintained between loudspeakers and sensitive equipment such as

CRT monitors or magnetic storage media.

Never attempt to carry out any operations, modifications or repairs that are not expressly described in

this manual. Contact your dealer or BASSBOSS support if the product is not functioning properly.

For installation purposes BASSBOSS strongly recommends that this product be installed by a qualified,

professional installer who can ensure correct installation and certify that it is installed in compliance

with the regulations in force.

The audio system must comply with current local standards and regulations regarding electrical systems.

WARNING

This is a class A product. In a domestic environment, this product may cause radio

interferences, in which case the user may be required to take corrective measures.

FCC Compliance Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at their own expense.

Important Notes

Shielded data cables must be used.

To minimize the occurrence of noise and interference, always use shielded signal cables. Avoid routing

signal or data cables close to equipment that produces high-intensity electromagnetic fields such as

transformers, power cables and loudspeaker wires.

Do not coil excess power cable. Do not coil or wrap power cables and signal or data cables together.

Manufacturer

True Lee Loudspeakers | BASSBOSS 2028 E Ben White Blvd. #240-8220 Austin TX 78741

We declare, under our sole responsibility, that to the best of our knowledge to which this

declaration relates, our products are in conformity with the applicable requirements.

Product: AT312-MK3 Loudspeaker Intended use: Professional Audio Loudspeaker

3-Way

Powered Top

AT312-MK3

bassboss.com/support

Need more assistance?

We’re here to help.

Tabla de contenidos

Otros manuales de Oradores de BassBoss

BassBoss

BassBoss SV9-MK3 Manual de usuario

BassBoss

BassBoss AT312 Attuned Top Manual de usuario

BassBoss

BassBoss DV8 Manual de usuario

BassBoss

BassBoss DV12-MK3 Manual de usuario

BassBoss

BassBoss MK3 Series Manual de usuario

BassBoss

BassBoss DV12-MKII Manual de usuario

BassBoss

BassBoss DV12 Manual de usuario

BassBoss

BassBoss MicroMain SV9 Manual de usuario

BassBoss

BassBoss AT212 Powered MicroMain Manual de usuario

BassBoss

BassBoss AT312 Attuned Top Manual de usuario

BassBoss

BassBoss AT212-MK3 Manual de usuario

BassBoss

BassBoss DiaMon 112 Manual de usuario

BassBoss

BassBoss SV8 Powered MicroMain Manual de usuario

BassBoss

BassBoss DIAMON-MK3 Manual de usuario

BassBoss

BassBoss DV12 Manual de usuario

BassBoss

BassBoss AT312 Attuned Top Manual de usuario

BassBoss

BassBoss DJ112 Manual de usuario

Manuales populares de Oradores de otras marcas

argon audio

argon audio IE20 Manual de usuario

Denon

Denon SC-N7 Manual de usuario

Gemline

Gemline Ace 3952 Manual de usuario

Focal

Focal ON WALL 300 Manual de instrucciones

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manual de usuario

SoundLogic

SoundLogic BCCS-6/6395 Manual de usuario

Peavey

Peavey DTH 218 Manual de usuario

Avantree

Avantree Pluto Air Manual de usuario

Morel

Morel Integra Series INTEGRA OVATION 4 Manual de usuario

Oppo

Oppo SONICA Manual de usuario

Bose

Bose SoundLink Wireless Music System Manual de usuario

Rocksteady

Rocksteady Stadium Manual de usuario

Bowers & Wilkins

Bowers & Wilkins 4 Manual de usuario

Sonance

Sonance SONOS OUTDOOR Series Manual de usuario

Electro-Voice

Electro-Voice EVID FM4.2 Manual de usuario

Pioneer

Pioneer XW-HTD630 Manual de usuario

Onn

Onn BWA16AA002 Manual de usuario

HP GL313AA - USB Speakers PC Multimedia Manual de usuario