©Basic Coatings • All Rights Reserved. • 1001 Brown Avenue • Toledo, Ohio 43607-0127
800-441-1934 • bcinfo@basiccoatings.com • www.basiccoatings.com
SURFACE PREPARATION
1. For new installations, refer to NWFA/MFMA specifications
and accepted procedures for acclimation of the wood, floor
preparation, and sanding.
2. Before sanding, clean the floor using Basic Coatings’ Squeaky
Cleaner following label instructions. Cleaning should be done to
remove contaminants from the floor.
3. Sand floors using accepted NFWA/MFMA procedures. All old
finish must be removed. A NIOSH dust mask should be worn
during sanding.
4. Finish sanding with new 120-grit screens is recommended.
5. Vacuum. Tack the floor with 3-4 clean terry cloth tack towels
dampened with mineral spirits to remove all dust caused by the
sanding and screening process. Tack until no residue collects on
the towels. Allow the floor to dry with good ventilation.
FINISH APPLICATION
Always maintain adequate ventilation during all phases of the coating
and drying process.
1. Stir product well before application.
2. Using Basic Coatings’ Applicator or lamb’s wool applicator,
apply
Quick Dry Sealer at the recommended coverage rate. Apply
with the grain.
3. Allow to dry, times will vary depending on conditions, usually
4 to 6 hours. Use air blowers to dry corners and dead air spots
thoroughly.
4. Abrade floor with new 100 to 120 grit screens is recommended.
5. Vacuum. Tack with 3 - 4 clean terry cloth tack towels dampened
with virgin mineral spirits to remove dust. Tack until no dust
residue collects on the towels. Allow the floor to dry with good
ventilation.
6. Apply second coat or finish coat in the same manner or following
manufacturers recommended instructions.
DRY TIME
Typical dry time is 4 to 6 hours depending on environmental
conditions. Allow longer dry times in low temperature or high
humidity environments.
PRECAUTIONS
KEEP OUT OF REACH OF CHILDREN. FOR PROFESSIONAL USE
ONLY.
CAUTION! COMBUSTIBLE. VAPOR AND SPRAY MIST HARMFUL.
CONTAINS MINERAL SPIRITS. MAY CAUSE DIZZINESS,
HEADACHE OR NAUSEA. CAUSES IRRITATION.
NOTICE: Reports have associated repeated and prolonged
occupational overexposure to solvents with permanent brain
and nervous system damage. Intentional misuse by deliberately
concentrating and inhaling the contents may be harmful or
fatal. Harmful or fatal if swallowed. Keep away from heat,
sparks and flame. Do not smoke. Extinguish all pilot lights and
turn off heaters, non-explosion-proof electrical equipment
and all other sources of ignition until vapors are gone.
Prevent build-up of vapors. Use with adequate ventilation. Do
not breathe vapors, dust or spray mist. Wear an appropriate,
properly fitted respirator (NIOSH approved) during and
after application unless air monitoring demonstrates vapor
mist levels are below applicable limits. Follow respirator
manufacturer’s directions for respirator use. Provide fresh
air ventilation during and after application. Wear protective
clothing. Close container after each use. Avoid contact with
eyes, skin and clothing. Wash thoroughly after handling. In case
of spillage, absorb and dispose of in accordance with federal,
state and local applicable regulations. To avoid spontaneous
combustion, soak oil rags and waste daily in water-filled metal
containers. Do not store above 100°F (38°C).
FIRST AID: If swallowed, call a physician immediately. Do NOT induce
vomiting. If affected by inhalation of vapor, remove to fresh air. If
breathing is difficult, get medical attention immediately. In case of
eye contact, flush immediately with plenty of water for 15 minutes
and call a physician. For skin, wash thoroughly with soap and water.
OBLIGATION OF MANUFACTURER
The following is made in lieu of all warranties, expressed or implied:
Seller’s and manufacturer’s only obligation shall be to replace such
quantity of the product proved to be defective. Neither seller nor
manufacturer shall be liable for any injury, loss or damage, direct
or consequential, arising out of the use of or the inability to use the
product. Before using, the user shall determine the suitability of the
product for the intended use and user assumes all risk and liability
whatsoever in connection therewith. The foregoing may not be altered
except by an agreement signed by officers of seller and manufacturer.
QUICK DRY SEALER
Quick Dry Sealer • 01.2015 • Page 2
