BARIX Annuncicom Manual de usuario
Annuncicom
Network-based, stand-alone intercom system for
custom home installations and commercial applications
Firmware: Version 4.0
Released: October 2013
Supports:
•Annuncicom 100
•Annuncicom 200
•PS1
•Annuncicom 60
•Annuncicom 155
•IPAM 100
•IPAM 102
•IPAM 302
USER MANUAL
Annuncicom User Manual Version 4.07
Table of Contents
1 Introduction ............................................................................................................................................................ 5
1.1 About the Annuncicom............................................................................................................................................. 5
1.2 Features................................................................................................................................................................... 5
1.3 Installing the Device................................................................................................................................................... 6
1.4 Additional Documents............................................................................................................................................... 6
1.5 Preloaded Firmware.................................................................................................................................................. 6
1.6 About this manual..................................................................................................................................................... 6
2 Controlling the Annuncicom ....................................................................................................................................
2.1 User menu interface.................................................................................................................................................. 8
2.2 Status and control..................................................................................................................................................... 8
3 Configuration ........................................................................................................................................................ 11
3.2 Configuration Overview........................................................................................................................................... 11
3.3 Basic Settings.......................................................................................................................................................... 12
3.4 Advanced Settings................................................................................................................................................... 13
3.5 Table Settings......................................................................................................................................................... 28
4 Reverting to factory defaults .................................................................................................................................. 30
5 Rebooting the device ............................................................................................................................................. 31
6 Updating the device ............................................................................................................................................... 32
6.1 STEP 1.................................................................................................................................................................. 32
6.2 STEP 2.................................................................................................................................................................. 32
6.3 STEP 3.................................................................................................................................................................. 33
6.4 STEP 4.................................................................................................................................................................. 33
7 The How To section ........................................................................................................................................... 34
7.1 How to set the Annuncicom for listening using WinAmp.............................................................................................34
7.2 How to listen using Windows Media Player................................................................................................................ 35
8 Application notes ................................................................................................................................................... 38
8.1 Two station intercom.............................................................................................................................................. 38
8.2 Door station and control station............................................................................................................................... 42
9 Advanced user section ........................................................................................................................................... 4
9.1 Network configuration using serial cable supplied........................................................................................................ 47
9.2 Network configuration using Telnet........................................................................................................................... 49
9.3 Control APIs for serial and Ethernet.......................................................................................................................... 49
9.4 Expert settings........................................................................................................................................................ 50
10 FAQ and Troubleshooting .................................................................................................................................... 51
11 Dictionary ........................................................................................................................................................... 52
12 Legal Information ................................................................................................................................................. 54
Annuncicom User Manual Version 4.07
Annuncicom User Manual Version 4.07
1 Introduction
1.1 About the Annuncicom
Congratulations on the purchase of your Annuncicom from Barix AG.
What exactly is the Annuncicom The Annuncicom is a network-based intercom, featuring fast setup,
operation over existing network connections, flexible use and easy reconfiguration.
The Annuncicom can work with other Annuncicom devices in a standalone configuration or can
seamlessly inter-operate with IT equipment like PCs.
Up to two buttons (Talk & Door, Talk & Emergency etc) plus relay output interface are available, which
allow the use of the Annuncicom in talk-back and door entry solutions.
Applications include
- Door intercom, talking over TCP/IP networks
- Alarming in public infrastructure, for example airports
- Remote paging connectivity via networks
- Residential intercom with network connectivity
- Automatic announcement systems
Each device can be configured to directly talk to up to 8 targets, via broadcast, or with the last calling
station.
An unlimited number of communication partners can be selected via web browser or serial interface
(directory connection).
The Annuncicom is the ideal solution to monitor entrances and to provide intercom and alarming
functionality in large residential, commercial and military building complexes like airports, office
buildings, malls and residential housing areas. It can also be used along highways or in tunnels to
provide IP based intercom capabilities.
No need for extra wiring when using existing network infrastructure or operating wireless, hence saving
implementation time and costs. Using only standard TCP/IP protocols, connecting remote facilities is
simple, and no changes to the existing WAN infrastructure are necessary.
1.2 Features
•Semi duplex two-way communication using mono audio streams.
•Choice of MPEG, G.711 and PCM audio formats.
•10/100 Mbit Ethernet connection
•Two button input (e.g. Talk & Door) plus relay output interface
•Controllable via a standard web browser (PC, PDA, Web tablet) or via a serial port
•Line in, Line out, built in amplifiers for microphone and speaker
•Features SonicIP® and IPzator™ technology
•Easy integration into existing IT and intercom infrastructure
BARIX AG | 28. Jan. 2014 | Introduction | Page 5/54
Annuncicom User Manual Version 4.07
1.3 Installing the Device
For the installation of the Barix Annuncicom devices please refer to the corresponding “Quick Install
Guide”. A printed version is included in the box and can also be downloaded from our site
www.barix.com.
1.4 Additional Documents
Technical specifications can be found in the corresponding product sheet which can be downloaded
from our site www.barix.com.
For detailed technical information on the CGI application programming interface (API) please download
the “Annuncicom Technical Documentation” from our website.
1.5 Preloaded Firmware
Barix pre-loads the “Annuncicom” firmware (from V4.06) on the Annuncicom 100 and Annuncicom 60 in
a multi package with SIP. Please choose the annuncicomic from the REBOOT page and reboot. If other
HW is being used then the factory firmware will have to be replaced.
Before continuing with this manual make sure that the firmware version is up to date and corresponds
with this manual. If not please proceed to the chapter “Updating the Device” in order to do so.
1.6 About this manual
1.6.1 inks to chapters
References to chapters (e.g. X Chapter name) are red and underlined and serve as direct links when
viewed in Adobe Acrobat Viewer. Click on the link to jump to the referenced chapter.
1.6.2 Bookmarks pane in Adobe Acrobat
The complete “Table of Contents” is available in Adobe Acrobat Viewer. Click on the “Bookmarks” pane
tab on the left side of Adobe Acrobat Viewer to open it. Click on any bookmark to directly jump to the
corresponding part of the manual.
1.6.3 Chapter overview
This technical documentation is divided into the following chapters:
•1 Introduction (This chapter)
•2 Contro ing the Annuncicom (Controlling the Annuncicom via the WEB UI)
•3 Configuration (How to configure the Annuncicom)
•4 Reverting to factory defau ts (Recovering the initial configuration)
•5 Rebooting the device
•6 Updating the device (How to update or change from “standard firmware”)
•7 The “How To” section (How to “listen” from Winamp or Media Player)
•8 App ication notes (Two common applications)
•9 Advanced user section (Serial port and Telnet Network configuration)
•10 FAQ and Troub eshooting
•11 Dictionary (technical names and expressions used in this manual)
•12 Legal Information
BARIX AG | 28. Jan. 2014 | Introduction | Page 6/54
Annuncicom User Manual Version 4.07
2 Controlling the Annuncicom
The Annuncicom has a local web server built in so that you can control it from anywhere on your
network using a standard web browser (from your PC, PDA or web tablet). This section describes the
WEB UI as seen on the Annuncicom 100. For other devices the pages are modified depending on what
features are supported on that particular HW. In which case the help pages provide the required
information. The Annuncicom web server can be customized to meet installation requirements.
Download the development kit from www.barix.com .
STEP 1
Open your web browser.
STEP 2
Type in the IP address of the Annuncicom in the address bar then press Enter.
You should now see the Home page of the Annuncicom in the browser window:
F1 Menu Frame
This frame allows selection of the Annuncicom web server features
Click on the selection to go to the relevant section.
F2 Status and control
This frame shows the current device status.
Several links allow control and simulation of button inputs, relay output and serial signals.
F3 Help
This frame shows the help for the available links in the device status page.
BARIX AG | 28. Jan. 2014 | Controlling the Annuncicom | Page 7/54
F1
F2
F3
Annuncicom User Manual Version 4.07
2.1 User menu interface
The menu frame is loaded once and remains in place as the following features are selected:
➢ Home
➢ Configuration
➢ Status
➢ Defaults
➢ Update
➢ Reboot
2.1.1 Red Bar
On the red bar is displayed the HW type, MAC address and the FW version loaded
2.1.2 Barix ogo
Clicking the Barix logo will bring you to the Barix homepage. (www.barix.com)
2.2 Status and control
BARIX AG | 28. Jan. 2014 | Controlling the Annuncicom | Page 8/54
Annuncicom User Manual Version 4.07
2.2.1 Stream
Shows the streaming mode and the audio format.
2.2.2 Audio
Shows the current Audio Input and Output Peak levels in dB, current volume in % and the audio input
source.
Volume Slider
In the audio section there is an imbedded volume slider. The volume level can be adjusted in steps of
5% and has immediate affect. Click closer to the + (plus) sign for higher volume or closer to the – (dash)
sign for lower volume. Clicking on the – (dash) sign decreases the volume by 5%. Clicking on the +
(plus) sign increses the volume by 5%. The changes are tempory. On device reboot the volume returns
to its configured setting.
2.2.3 Status
Shows the current audio status.("IDLE", "TALKING", "TALKING SUPPRESSED", "FORCED TALKING"
and "LISTENING"). Click the "FORCE" link to force talking This overrides the "LISTENING" mode, e.g.
when an other device is talking to this device. Click the "TALK" link to start talking. Click the "STOP"
link to stop talking. The Status indicator has the following meaning: GREY: not talking, GREEN: talking,
RED: forced talking. On
"send always"
the buttons are not visible and the status is permanently set to
"FORCED TALKING"
Table
Select the streaming table by number. Go to the configuration Basic or Table settings to create table
entries.
Entry
Select "All" for talking to all configured entries within the table. Select a particular number to talk only to
that entry.
2.2.4 I/0
The Annuncicom software supports 2 digital inputs and 1 digital output. In addition CTS and RTS can
also be used as digital input/output signals. Any signals not provided by the Annuncicom HW are not
displayed.
Button 0 and 1
Click the "SET" link to simulate the button being pushed.
Click the "CLR" link to simulate the button being released.
The indication next to "BUTTON" has the following meaning:
GREY: released, GREEN: pushed (simulation is not shown!)
Relay
Click the "TOGGLE" link to activate the relay for the "Relay toggle duration" time, adjustable in
"Settings" under "I/O". Click the "SET" link to activate the relay, the "CLR" link to deactivate the relay.
The indicator next to "RELAY" shows the physical status of the relay: GREY for inactivated, GREEN for
activated.
BARIX AG | 28. Jan. 2014 | Controlling the Annuncicom | Page /54
Annuncicom User Manual Version 4.07
CTS IN (RS-232)
Click the "SET" link to simulate CTS being activated. Click the "CLR" link to simulate CTS being
deactivated. The indicator next to "CTS IN" shows the physical status of the CTS GREY: inactive,
GREEN: active (simulation is not shown!)
- not activated
- activated
RTS OUT (RS-232)
Click the "SET" link to activate RTS. Click the "CLR" link to deactivate RTS. The indicator next to "RTS
OUT" shows the physical status of the RTS:
- not activated
- activated
2.2.5 Supervision
One of the range of Annuncicom HW, the Annunciocm 155, also supports supervision of microphone,
speaker and temperature. On the Annuncicom 155 the following fields are also displayed.
MIC
This field shows the status of the microphone:
- microphone detected and operating properly
- microphone not attached or short-cut detected
SPEAKER
This field is available only on devices supporting supervision. Shows the status of the attached speaker.
The speaker is supervised with an in-band tone. The supervision must be configured in the Audio
section and is by default off. The following values are displayed:
- supervision switched off or no value available yet
- speaker detected and operating properly
- speaker not attached or short-cut detected
TEMP
Shows the device's internal temperature in degrees centigrade. The information is available only on
devices supporting supervision.
BARIX AG | 28. Jan. 2014 | Controlling the Annuncicom | Page 10/54
Este manual sirve para los siguientes modelos
8
Otros manuales de Sistema de intercomunicación de BARIX
BARIX
BARIX Annuncicom PS Touch Manual de usuario
BARIX
BARIX annuncicom 100 Manual de usuario
BARIX
BARIX Annuncicom 155 Manual de usuario
BARIX
BARIX Annuncicom 1000 Manual de usuario
BARIX
BARIX annuncicom 100 Manual de usuario
BARIX
BARIX Annuncicom IC Manual de usuario
BARIX
BARIX Annuncicom 60 Manual de usuario
