Barco RLM W6 Manual de usuario
-1-
SERVICE MANUAL
BARCO RLM W6
-2-
Version Description Date
00 Initiation Nov. 4, 2009
01 Modification Content per Barco Nov. 25th e-mail Nov.27,2009
02 Modification Content per Barco Nov. 30th e-mail Nov.30,2009
03 Modification Content per Barco Dec. 1st e-mail Dec.2,2009
04-A Modification Content per Barco Dec. 2nd e-mail Dec.3,2009
04-B Add error code description Dec.15,2009
04-C Modification Content per Barco Jan. 28th e-mail Jan.28,2010
04-D Modification Content per Barco Mar. 4th e-mail Mar. 4,2010
-3-
BARCO RLM W6 Projector
PLEASE NOTE
The information contained herein is based on the experience and knowledge relating
to the subject matter gained by Barco prior to publication. No patent license is
granted by this information.
Barco reserves the right to change this information without notice, and makes no
warranty, express or implied, with respect to this information. Barco shall not be
liable for any loss or damage, including consequential or special damages, resulting
from any use of this information, even if loss or damage is caused by Barco’s
negligence or other fault.
This equipment includes parts and assemblies sensitive to damage from
electrostatic discharge. Use caution to prevent damage during all service
procedures.
-4-
Table of Contents
zIntroduction of the product & Safety precautions
zUnpack the unit
zBlock Diagram
zRemote control use
zBoard location
zFan location
zCleaning unit procedure
zKits definition & Pictures
zReplacing procedures
zRS-232 communication
zRecommended Spare Part List
zSoftware download process
zTiming chart
-5-
zIntroduction of the product & Safety precautions
BARCO (RLM W6) is compact WUXGA (1920 x 1200 Widescreen Ultra Extended Graphics
Array), and 3-Chip DLPTM high-definition images projector. It shares a common
mechanical, electrical, and optical platform.
BARCO (RLM W6) is designed with 0.67” DMD (Digital Micro mirror Device) with 280W
dual lamp.
1. Cleaning the Projector
A). Cleaning the projector to remove dust and grime will help ensure trouble-free
operation.
1). Be sure to turn off and unplug the projector at least 30 minutes before cleaning.
Failure to do so could result in a severe burn.
2). Use only a dampened cloth when cleaning.
Do not allow water to enter the ventilation openings on the projector.
3). If a little water gets into the projector interior while cleaning,
leave unplugged in a well-ventilated room for several hours before using.
4). If a lot of water gets into the projector interior when cleaning, have the projector serviced.
B). Cleaning the Projection Lens
*When dust and fingerprints, etc. are on the lens surface, use
the designated glass cleaner (toraysee) to remove it as shown in the
figure at the right. For fingerprints and other soiling that are difficult
to remove with a dry cloth, use a designated glass cleaner (toraysee)
which has been moistened in water and then use a dry cloth
to dry it off. Or, apply a little optic lens cleaner to a clean soft cloth.
(Do not apply the cleaner directly to the lens.) Then, lightly wipe the lens
in a circular motion.
-6-
Caution:
*The projection lens surface has a special coating.
1. Do not use abrasive cleaners and detergents or solvents on the
surface.
2. To prevent discoloration or fading, avoid getting cleaner on the
projector case
C). Cleaning the Main Unit
1. Clean with a soft fuzz-free cloth. In case of severe soiling, use
a well-wrung cloth dipped in a neutral agent to remove soiling
and then finish with a dry cloth.
*Do not clean with thinner, benzene or similar agents as this
could lead to deterioration or peeling of paint.
2. In case of dust in suction or exhaust holes or the interior,
disassemble the main unit and use air to remove the dust from
the inside.
D). Cleaning the filters
In order to keep the interior of the projector clean, the projector is equipped with a filter to
keep out dust and other small particles. Normally, it is recommended that you change the
projector's filter around 500 hours of projector operation at least. If you are operating the
projector in a dusty environment, it is recommended that you clean the filter more often.
When used in fog machine environment, a filter change is recommended on a regular base.
-7-
The interval is depending on the smoke density.
Dust clogs at the filter will prevent the projector from drawing cool air to lower the internal
temperature. This could lead to overheating and cause the projector to malfunction or
become damaged.
Use a vacuum cleaner to clean the ventilation slots.
To clean the filter at the ventilation slots, refer to the following illustration:
Step1: Loosen the two screws on the cover of the ventilation slot.
:
Loosen the 2 screws
-8-
Step2: Remove the dirty filter; you can clean it directly using water. Leave it to dry
before replacing it for further use. If the filter is broken or greasy, please replace it by
a new one. (Filter Part nr: R9899704).
Take out the filter and clean it
Step3: Insert the clean filter.
Put the clean filter inside the cover
-9-
Step4: Reattach the filter cover and tighten the two screws.
Close the filter cover
Then, fasten the two screws
-10-
E). Lamp Replacement
The lifecycle of ordinary projection lamp typically lasts for 1500 hours before requiring
replacement (different lamp configurations will affect lamp life). From the OSD Menu, you can go
to LAMPS
ÆLamp1 or 2 Run Time to check how long a lamp has been used. You should also replace the
lamp when the projected image gets noticeably darker. Contact your local dealer to purchase new
certified lamps for your projector.
To replace the projector lamp
Step1: Turn off the projector and unplug the power cord. Let the projector cool for
approximately 15 minutes before removing the lamp module for replacement.
When you turn off the projector, the lamp inside the projector will still be very hot (approximately 200 ~ 300°C).
If you attempt to replace the lamp without allowing the projector to cool, you could risk scalding yourself. This
is why you should wait for no less than 15 minutes for the lamp to cool down in order to perform the
replacement safely.
Step2: Loosen the Lamp cover.
Loosen the 2 screws
Otros manuales para RLM W6
1
Tabla de contenidos
Otros manuales de Proyector de Barco
Barco
Barco ELM Series Manual de usuario
Barco
Barco DP2K Series Manual de usuario
Barco
Barco UDM Series Manual de usuario
Barco
Barco BarcoReality SIM 6 Manual de usuario
Barco
Barco Prometheus III Manual de usuario
Barco
Barco R9001190 Manual de usuario
Barco
Barco DP4K-P Manual de usuario
Barco
Barco GALAXY 4 LL+ Manual de usuario
Barco
Barco F70 Series Manual de usuario
Barco
Barco C-10 Manual de usuario
Barco
Barco DP2K--32B Manual de usuario
Barco
Barco CR series Manual de usuario
Barco
Barco R9001310 Manual de usuario
Barco
Barco G62 Manual de usuario
Barco
Barco R9001560 Manual de usuario
Barco
Barco HDF W series Manual de usuario
Barco
Barco Galaxy 4 Long Life+ R9040355 Manual de usuario
Barco
Barco R9002240 Manual de usuario
Barco
Barco R9002250 Manual de usuario
Barco
Barco HDX W18 Manual del propietario
