Barco FL40 series Manual de usuario

FL40 series

Quick Start Guide

Projector Main Components and interfaceProjector Main Components and interface

Warning

Risk Group 2 (RG2) LED product according to IEC EN 62471-5.

Do not stare in to beam

Refer to user manual before operating

Do not attempt to disassemble or modify this projector.

Download Product Manual

Product manuals and documentation are available online at www.barco.com/en/support/ﬂ40-wu

Registration may be required; follow the instructions given on the website.

IMPORTANT!

Read Installation Instructions before connecting equipment to the mains power supply.

435

18217

1Adjustable feet

2Projector lens

3Lens holder

4IR receiver: For receiving remote control signals

LCD panel

6Keypad. Used for local operation of the projector

Connector panel: Control and communication interface 8Lens lock handle

- 2 -

Control & communication connectionsControl & communication connections

1Menu Navigation

2Menu Selection

3Open Menu

4Menu Back

5Power On/O

6OSD On/O

7Input Selection

8Shutter Open/Close

9Test Patterns

10 Lens Menu

11 LCD Panel

10 9 8 7

1 2 3 4 5 6

Local keypad

Button backlight status

BUTTON COLOR STATUS DESCRIPTION

Projector starts up (Booting)Blinking WHITE

Projector is in StandbySolid WHITE

Blinking RED Error condition

Blinking BLUE Projectorgoes to ON mode

Projector is ON

Power button

Solid BLUE

O Projector not in power ON state

Solid WHITE Shutter is open

Shutter is closedSolid RED

Shutter button

1288910

3567

RS-232: 9- pin DB9 Connector

Sync Port IN/OUT - BNC / Bidir mini-DIN

Trigger: 12VDC - 0,5A (6W)

RC: Jack connector for wired remote

DP: Standard Display port

LAN: Standard RJ45 connector

Usb 2.0 type A, 4 pin

Dual DVI-I 1.0 (DVI_D Functionallity)

HDMI: Standard HDMI 2.0

HDBaseT: Standard RJ45 8P8C

110-240V

Connect power

Press Power On Button

Installation ConditionsInstallation Conditions

Ventilation RequirementsVentilation Requirements

Power up procedure

Power down procedure

110-240V

Pull out Connector

Press Power Button for 3 sec

250mm

1. Plug in mains power cord

2. The projector will run a start up procedure. When completed,

the standby button illuminates white. (Standby mode).

3. Press power button again to bring the projector in ON mode.

When the power button backligh is steady blue,

the projector are ready for use.

1. Press the power button for 3 seconds

2. The power button will illuminate white, and

the projector enters the cooling down process.

3. Wait until the cooling down process are

completed before removing the main power

cord from the projector

- Review source information in the status menu (LCD screen or OSD) and verify that the source signal is compatible.

- Use test image to verify that the correct aspect ratio is selected

- Reset color and display settings to factory settings

- Restart the projector. Let the unit cool down for at least 1 minute prior to restarting

- Check the lenght of the source cables, and try shorter cables

Failure indications

What to do when the content or color is not correct

Caution

Do not place heat sensitive

objects in the area of the

orange arrow

Ambient operating conditions:

Temperature: 10 - 40°C

Altitude 1500 - 3000m

Temperature: 10 - 35

°C

Humidity: 10 - 80% RH

Humidity: 10-80% RH

Altitude 0 - 1500m:

Power requirements:

100 - 240 V, 60 - 50 Hz

Dimensions excl. lens:

450 x 471 x 244mm (WxLxH)

Weight excl. lens: 21,5 kg

NOTE !

The operating conditions will change when dust or pollution ﬁlters are installed.

Refer to ﬁlter installation manual for correct data

RCU batteries

- Two AA size batteries. Use alkaline batteries for optimum range and life time.

- Replacing batteries will reset the broadcast address of the RCU to its default value ’0’.

- Replacing batteries switches on the RCU automatically.

1Button pressed indicator

2Shutter Open

3Shutter Close

4LCD panel On/O

5OSD On/O

6Lens Zoom

7Lens Shift

8MenuOpen/Close

9Menu Selection, OK button

10 Menu Navigation

11 Input Selection

12 Address button

13 Numeric buttons

14 Backspace (when entering values)

15 XLR connector

16 Decimal mark (when entering values)

17 Macro button

18 MenuBack

19 Defaultbutton

20 Lens Focus

21 Color menu

22 Test Patterns

23 Power On

24 Power O

25 3.5 mm jack

26 RCU On/O

25 26

14 16

RCU buttons

Lens Removal

Installing lens

1. When removing the lens, always close the shutter, see keypad explanation. Press Shutter keypad, and verify

that the shutter keypad turn in to red illumintation. This indicate that the shutter is closed. When new lens is installed,

open shutter by pressing the shutter key again.

Shutter open state is veriﬁed when the shutter key illuminates white.

3. Pull the lens straight out of the lens mount.

NOTE!! To prevent damage to the lens, and dust contamination in the projector light processor, always replace the

lens bayonet cap, lens front cap and projector lens cap immediately after removing the lens.

2. Move the lever to the far left position

Always keep shutter closed

when installing or removing the lens.

1. When handling lens in or out, always close shutter, see keypad explanation. Press Shutter keypad, and verify

that the shutter keypad turn in to red illumination. This indicate that the shutter is closed. When the lens is

installed, open shutter by pressing the shutter key. Shutter open state is veriﬁed when the shutter key

illuminates white.

2. Verify that the lens release lever is in it’s default position,

at the far left of the slide, as illustrated

3. Remove the protective cap at the lens bayonet end

4. Align the lens so that the red marking on the bayonet

end is facing upwards.

5. Install the lens bayonet into the lens mount, and then move the lever to the right. Check that the lever is ﬁrmly

Warning

ENABLING BRIGHT OUTCOMES

Software upgradeSoftware upgrade

The projector is now ready for normal operation.

1. Go to www.barco.com and select your product. All available ﬁrmware downloads are ﬁled under

the Technical Downloads tab

2. Download the ﬁrmware. Extract and save the ﬁle to a USB Stick with FAT ﬁle system. Use the eject function on

your PC to safely remove the device from your computer.

3. Place the projector in Standby mode (status indicator is steady white).

4. Insert the USB stick into one of the projector’s rear USB ports.

After a few seconds, the status indicator will ﬂash. (Rate: 3 Hz/180 FPM). This signals that the upgrade is in progress.

If the upgrade ﬁle is corrupt or invalid, the status indicator will turn red and the upgrade process will stop.

Note! The upgrade will not be installed in this instance, and the upgrade process must be restarted with a full and correct ﬁle.

The projector may restart several times during the upgrade process

5. The LCD display will show the progress of the update procedure, and also when the USB stick must be removed.

The projector will return to standby mode (status indicator is steady) once the upgrade is completed successfully.

NOTE !

Once initiated, the upgrade procedure can take up to 20 minutes to complete.

CAUTION !

Do NOT turn o, power down, or remove mains

power supply to the projector when an upgrade is in progress.

Doc No: R5910124 / 02

Otros manuales para FL40 series

Tabla de contenidos

Otros manuales de Proyector de Barco

Barco

Barco Cine 8 Manual de usuario

Barco

Barco R9002327 Manual de usuario

Barco

Barco DP K-32B Series Manual de funcionamiento

Barco

Barco R9001490 Manual de usuario

Barco

Barco R9010310 Manual de usuario

Barco

Barco HDX W18 Manual del propietario

Barco

Barco 90 00719 Manual de usuario

Barco

Barco CR series Manual de usuario

Barco

Barco B-10 Mobile LED R9855510 Manual de instrucciones

Barco

Barco Cineo22 Manual de usuario

Barco

Barco CineVersum 120 Manual de usuario

Barco

Barco HDX 4K Manual de usuario

Barco

Barco MiPIX-20 Manual de usuario

Barco

Barco DP2K-23B Manual de usuario

Barco

Barco UDM Series Manual de usuario

Barco

Barco BarcoiQ GRAPHICS 500 Manual de usuario

Barco

Barco RLS W12 Manual de usuario

Barco

Barco R9850010 Manual de usuario

Barco

Barco BARCOELM R18 Manual de usuario

Barco

Barco R9001280 Manual de usuario

Barco

Barco iCon H250 Manual de usuario

Barco

Barco SLM R12 Plus Manual de usuario

Barco

Barco R9001320 Manual de usuario

Barco

Barco PJWU-101B Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario