Barco Galaxy WARP 10 HB Manual de usuario

Barco Galaxy WARP™ 10 HB

Owner’s Manual

R9040330

R5976698/00

05/04/2004

Barco nv Simulation Products

600 Bellbrook Ave, Xenia OH 45385

Phone: +1 (937) 372 7579

Fax: +1 (937) 372 8645

E-mail: eis@barco.com

Visit us at the web: www.eis.barco.com

Barco nv Simulation Products

Noordlaan 5, B-8520 Kuurne

Phone: +32 56.36.82.11

Fax: +32 56.36.84.86

E-mail: [email protected]

Visit us at the web: www.barco.com

PrintedinBelgium

stored in a retrieval system without the prior written consent of Barco.

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-

ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the

program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this

publication; these changes are incorporated in new editions of this publication.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.

All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for

the products or their manufactures.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser

must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco

must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,

at latest 30 days after the transfer of risks. In the event of justified notice of compliant, Barco can repair the fault or provide a replacement

at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a

reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or

indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component

of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties

guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,

in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not

agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are

system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as

well as normal maintenance are not subject to the guarantee provided by Barco either.

The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by

the customer.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may

cause harmful interference, in which case the user will be responsible for correcting any interference.

Table of contents

TABLE OF CONTENTS

1. SafetyInstructions.................................................................................................. 5

1.1 Warnings............................................................................................................................... 5

1.2 Restricted Access Location........................................................................................................... 5

1.3 FCC statement ........................................................................................................................ 6

1.4 Note.................................................................................................................................... 6

2. Packaging andDimensions .......................................................................................7

2.1 Box Content ........................................................................................................................... 7

2.2 Lens Packaging . . . .................................................................................................................... 7

2.3 Dimensions............................................................................................................................ 7

3. InstallationGuidelines..............................................................................................9

3.1 General . ............................................................................................................................... 9

3.2 Restricted Access Location.......................................................................................................... 10

3.3 Projector Position .................................................................................................................... 11

3.4 Configuration ......................................................................................................................... 11

3.5 Safety Area around the projector....................................................................................................13

3.6 Re-adjusting the lamp position in the lamp casing..................................................................................14

3.7 Lenses . . ..............................................................................................................................16

3.7.1 Lenses . . . . . . ...................................................................................................................16

3.7.2 Lens selection . . ...............................................................................................................16

3.7.3 Lens formulas. . . ...............................................................................................................16

3.7.4 Lens Installation ...............................................................................................................17

3.7.5 Cleaning the lens . . . ...........................................................................................................17

3.8 Battery Installation in the RCU.......................................................................................................18

4. Connections.........................................................................................................19

4.1 Power connection . ...................................................................................................................19

4.2 Switching On .........................................................................................................................19

4.3 Switching to standby . . ...............................................................................................................20

4.4 Switching off.......................................................................................................................... 20

4.5 Input Connections . ...................................................................................................................21

4.5.1 Input Facilities . . ...............................................................................................................21

4.5.2 Input 1..........................................................................................................................21

4.5.3 Input 2..........................................................................................................................22

4.5.4 Inputs via RCVDS05...........................................................................................................23

4.6 Communication Connections . . . . ....................................................................................................23

4.6.1 Linked System .................................................................................................................23

4.6.2 RS232 (RS422) connection . . . ................................................................................................27

4.6.3 Communication with peripherals..............................................................................................27

4.7 Stereo Connections ..................................................................................................................27

4.7.1 Single Channel Stereo Connections . . . . . .....................................................................................27

4.7.1.1 Left/Right Phasing Module (Input 3). . . .................................................................................27

4.7.2 Multi-Channel Stereo Connections............................................................................................28

4.7.2.1 Stereo Set Up...........................................................................................................28

4.7.2.2 Single CADWall Configuration..........................................................................................29

4.7.2.3 Multiple CADWall (Showroom Installation).............................................................................30

5. GettingStarted......................................................................................................33

5.1 RCU & Local keypad.................................................................................................................33

5.2 Terminology overview ................................................................................................................33

5.3 Operating the projector...............................................................................................................35

5.3.1 Switching On...................................................................................................................35

5.3.2 Switching to standby...........................................................................................................36

5.3.3 Switching off ...................................................................................................................36

5.3.4 Temperature error DMD.......................................................................................................36

5.4 Quick Set Up Adjustments...........................................................................................................36

5.4.1 Quick Lens Adjustment . . . . ....................................................................................................36

5.4.2 Quick OSD Color Change . ....................................................................................................37

5.5 Using the RCU .......................................................................................................................38

5.6 Controlling the Projector .............................................................................................................42

5.6.1 Common Address .............................................................................................................42

5.6.2 Projector Address..............................................................................................................42

5.6.3 RCU Address .................................................................................................................. 42

5.6.4 Input Selection . . ...............................................................................................................43

5.6.5 Picture Controls................................................................................................................43

5.6.6 Menus on Local LCD Display . ................................................................................................44

6. Random Access ....................................................................................................45

6.1 Random Access Overview...........................................................................................................45

6.2 Starting Up Random Access......................................................................................................... 46

6.3 File Service...........................................................................................................................47

6.3.1 File annotation . . ...............................................................................................................47

R5976698 BARCO GALAXY WARP™ 10 HB 05/04/2004 1

Table of contents

6.3.2 Possible file manipulations....................................................................................................48

6.3.3 Starting Up File Service .......................................................................................................48

6.3.4 Load File . . . . ...................................................................................................................48

6.3.5 Edit WARP1....................................................................................................................49

6.3.6 Edit WARP2....................................................................................................................50

6.3.7 Changing the settings . . . . . ....................................................................................................50

6.3.8 Correct value...................................................................................................................51

6.3.9 Edit WARP2 File...............................................................................................................53

6.3.10 Rename File ...................................................................................................................53

6.3.11 Copy File....................................................................................................................... 54

6.3.12 Delete File .....................................................................................................................55

6.3.13 File Options....................................................................................................................56

6.4 Picture Tuning........................................................................................................................57

6.4.1 Starting Up Picture Tuning ....................................................................................................57

6.4.2 Gamma ........................................................................................................................57

6.4.3 Input Balance 1 . ...............................................................................................................58

6.4.4 Input Balance 2 . ...............................................................................................................61

6.4.5 Windowing .....................................................................................................................61

6.4.5.1 Starting Up Windowing .................................................................................................62

6.4.5.2 Blanking (Windowing)...................................................................................................62

6.4.5.3 Shift (Windowing) . . . ....................................................................................................64

6.4.5.4 Size (Windowing) .......................................................................................................65

6.4.5.5 Geo Soft Edge ..........................................................................................................66

6.5 Geometry.............................................................................................................................66

6.5.1 Introduction ....................................................................................................................67

6.5.2 Starting Up Geometry .........................................................................................................67

6.5.3 Geometry file annotation . . ....................................................................................................67

6.5.4 Setting up a new Geometry file ...............................................................................................67

6.5.5 Possible Geometry file manipulations ........................................................................................68

6.5.6 Load . . ..........................................................................................................................68

6.5.7 Edit.............................................................................................................................69

6.5.7.1 Introduction. . . ...........................................................................................................70

6.5.7.2 Start up..................................................................................................................71

6.5.7.3 Coarse...................................................................................................................71

6.5.7.3.1 Start up............................................................................................................71

6.5.7.3.2 Corner selection ..................................................................................................71

6.5.7.3.3 Corner adjustment ................................................................................................72

6.5.7.3.4 Side Bow selection................................................................................................74

6.5.7.3.5 Bow shaped pre-distortion set up . . . .............................................................................76

6.5.7.3.6 Coarse linearity adjustment using Side Bows ...................................................................76

6.5.7.3.7 Center selection...................................................................................................78

6.5.7.3.8 Center adjustment ................................................................................................78

6.5.7.4 Linearity adjustment ....................................................................................................79

6.5.7.4.1 Start up............................................................................................................79

6.5.7.4.2 Horizontal or Vertical Linearity selection .........................................................................80

6.5.7.4.3 Horizontal Linearity adjustment ..................................................................................80

6.5.7.4.4 Vertical Linearity adjustment .....................................................................................82

6.5.7.5 Fine...................................................................................................................... 83

6.5.7.5.1 Start up............................................................................................................84

6.5.7.5.2 Horizontal or Vertical Linearity selection .........................................................................84

6.5.7.5.3 Fine Horizontal or Vertical Linearity adjustment . . . ..............................................................85

6.5.7.5.4 Bow Linearity selection ...........................................................................................86

6.5.7.5.5 Bow Linearity adjustment.........................................................................................87

6.5.7.5.6 Quadrant selection................................................................................................88

6.5.7.5.7 Quadrant adjustment . ............................................................................................89

6.5.7.5.8 Local selection ....................................................................................................90

6.5.7.5.9 Local adjustment..................................................................................................91

6.5.7.6 Shift...................................................................................................................... 92

6.5.7.7 Transport Delay ......................................................................................................... 92

6.5.7.8 Blanking .................................................................................................................94

6.5.7.8.1 Blanking Start up..................................................................................................94

6.5.7.8.2 Blanking Active On................................................................................................95

6.5.7.8.3 Blanking Shape Start up . . . . ......................................................................................95

6.5.7.8.4 Blanking Shape selections . . .....................................................................................95

6.5.7.8.5 Blanking adjustment ..............................................................................................96

6.5.7.9 Electronic Soft Edge (Optional).........................................................................................97

6.5.7.9.1 Introduction. . . . ....................................................................................................97

6.5.7.9.2 Preparations . . ....................................................................................................98

6.5.7.9.3 Soft Edge Start up ................................................................................................99

6.5.7.9.4 Soft Edge Active On ..............................................................................................99

6.5.7.9.5 Soft Edge Shape Start up . . . .....................................................................................99

6.5.7.9.6 Soft Edge Shape selections . ....................................................................................100

6.5.7.9.7 Basic Soft Edge Shape Set up .. ................................................................................101

6.5.7.9.8 Soft Edge Width Start up ........................................................................................103

6.5.7.9.9 Soft Edge Width selections......................................................................................103

6.5.7.9.10 Basic Soft Edge Width Set up...................................................................................104

2R5976698 BARCO GALAXY WARP™ 10 HB 05/04/2004

Table of contents

6.5.7.10 Reset ...................................................................................................................106

6.5.7.10.1 Start up...........................................................................................................106

6.5.7.10.2 Coarse Reset ....................................................................................................106

6.5.7.10.3 Linearity Reset ...................................................................................................107

6.5.7.10.4 Reset Fine .......................................................................................................107

6.5.7.10.5 Reset Blanking/Soft Edge .......................................................................................107

6.5.7.10.6 Reset All..........................................................................................................108

6.5.8 Rename . . . . . ..................................................................................................................109

6.5.9 Copy ..........................................................................................................................110

6.5.10 Delete .........................................................................................................................110

6.6 Stereo Options ......................................................................................................................111

6.6.1 Starting Up Stereo Options...................................................................................................111

6.6.2 Stereo Phase .................................................................................................................111

6.6.3 Invert Stereo..................................................................................................................112

6.6.4 Master Channel . ..............................................................................................................113

6.6.5 Stereo Mode..................................................................................................................114

6.6.6 Dark Time.....................................................................................................................114

6.6.7 Forced Asynchronous ........................................................................................................117

7. InstallationMode................................................................................................. 119

7.1 Installation Mode Overview .........................................................................................................119

7.2 Starting Up Installation..............................................................................................................120

7.3 Input Slots . . .........................................................................................................................120

7.4 No Signal . . . .........................................................................................................................121

7.4.1 Starting Up No Signal . . . . . ...................................................................................................121

7.4.2 Changing the Background Color . . ...........................................................................................121

7.4.3 Changing the Shutdown Setting . ............................................................................................122

7.4.4 Changing the Shutdown Time Setting . . .....................................................................................122

7.5 Lens Adjustment . . ..................................................................................................................123

7.5.1 Starting Up Lens Adjustment. . ...............................................................................................123

7.5.2 Lens Zoom/Focus Adjustment ...............................................................................................123

7.5.3 Lens Shift Adjustment . . . . . ...................................................................................................124

7.6 Changing the Menu Position........................................................................................................124

7.7 800–Peripheral . . . . ..................................................................................................................125

7.7.1 Starting Up 800–Peripheral . . . ...............................................................................................125

7.7.2 Defining the Communication Protocol of the RCVDS05 ....................................................................125

7.7.3 COM800 Protocol.............................................................................................................126

7.8 Configuration ........................................................................................................................126

7.9 OSD Color...........................................................................................................................127

7.10 Internal Patterns.....................................................................................................................127

8. Service Mode...................................................................................................... 129

8.1 Service Mode Overview.............................................................................................................129

8.2 Build-up..............................................................................................................................129

8.3 Starting Up Service..................................................................................................................130

8.4 Identification Screen . . ..............................................................................................................130

8.5 Change Password...................................................................................................................131

8.6 Change Projector Address..........................................................................................................131

8.6.1 Starting Up Change Projector Address . . ....................................................................................132

8.6.2 Changing the Projector Address .............................................................................................132

8.6.3 Changing the Common Address . . ...........................................................................................133

8.7 Change Baudrate PC ...............................................................................................................133

8.8 Lamp Menu..........................................................................................................................134

8.8.1 Starting Up the Lamp Menu..................................................................................................134

8.8.2 Constant Light Output (CLO).................................................................................................135

8.8.3 Lamp Mode ...................................................................................................................136

8.9 Barco Logo ..........................................................................................................................136

8.9.1 Starting Up Barco Logo . . . ...................................................................................................136

8.9.2 Barco Logo Status . . ..........................................................................................................137

8.9.3 Barco Logo Background. . . ...................................................................................................137

8.9.4 Shift Barco Logo ..............................................................................................................138

8.9.5 Hot Key .......................................................................................................................138

8.10 Preset Input Balance 1..............................................................................................................138

8.11 Preset Input Balance 2..............................................................................................................139

8.12 Electronic Convergence.............................................................................................................139

8.13 Diagnosis . . . .........................................................................................................................140

8.13.1 Starting Up Diagnosis . . . . . ...................................................................................................140

8.13.2 I2C Diagnosis .................................................................................................................141

8.13.3 Formatter Diagnosis ..........................................................................................................141

8.13.4 SMPS Diagnosis..............................................................................................................142

8.14 DynaColor™.........................................................................................................................142

A.StandardSource Files........................................................................................... 145

A.1 Table overview ......................................................................................................................145

Index.................................................................................................................... 147

R5976698 BARCO GALAXY WARP™ 10 HB 05/04/2004 3

Table of contents

4R5976698 BARCO GALAXY WARP™ 10 HB 05/04/2004

1. Safety Instructions

1. SAFETY INSTRUCTIONS

1.1 Warnings

To prevent personnel injury

The customer should never attempt to disassemble the lamp casing or to dispose of the lamp casing other than by returning it to

BARCO.

To prevent injuries and physical damage, always read this manual and all labels on the system before connecting to the wall outlet,

or adjusting the projector.

To prevent injuries, take note of the weight of the projector. Minimum 4 persons are needed to carry the projector.

NEVER look into the lens ! Due to the high luminance damage to the eye can happen.

Before attempting to remove the projector’s cover, you must turn off the projector and disconnect from the wall outlet.

When performing set up work at a ceiling mounted projector, to prevent injury caused by falling objects or the system, set out a keep

out area.

Consult a professional structural engineer prior to suspending the ceiling mount from a structure not intended for that use. Always

ensure the working load limit of the structure supporting the projector.

The power input at the projector side is considered as the disconnect device. When mentioned to switch of the projector, to access

some parts inside, always disconnect the power cord at the projector side.

To prevent projector damage

If the Air Filters are not regularly replaced, the air flow inside the projector could be disrupted, causing overheating. Overheating

may lead to the projector shutting down during operation.

In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility requirements,

it should always be operated with all of it’s covers in place.

Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains supply

immediately. Do not operate the projector again until it has been checked by qualified service personnel.

The projector must always be mounted in a manner which ensures free flow of air into its air inlets and unimpeded evacuation of the

hot air exhausted from its cooling system. Heat sensitive materials should not be placed in the path of the exhausted air.

Special care should be used when DLP projectors are used in the same room as performant laser equipment. Direct or indirect

hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices (TM) in which case there is a loss of warranty

To prevent battery explosion

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

1.2 Restricted Access Location

Installation in a Restricted Access Location

The Barco Galaxy WARP™ 10 HB can only be installed in a Restricted Access Location.

What is a Restricted Access Location (Definition)?

Definition of a Restricted Access Location:

A location for equipment where both of the following paragraphs apply:

• Access can only be gained by SERVICE PERSONS or by USERS who have been instructed about the reasons for the restriction

applied to the location and about the precautions that shall be taken.

• Access is through the use of the TOOL or lock and key, or other means of security, and is controlled by the authority responsible

for the location.

What are the Reasons for the Applied Restriction?

The Air Outlet Grill on the side of the Projector can reach high temperatures due to the High Light Output Range of the lamp.

R5976698 BARCO GALAXY WARP™ 10 HB 05/04/2004 5

1. Safety Instructions

Image 1-1

The Air Outlet Grill on the side of the Projector can reach high temperatures

WARNING:Do not touch this Air Outlet Grill when the projector is switched on, respect a cool down period

of 10 minutes before touching this Grill, when switching off the projector!

1.3 FCC statement

Federal Communication Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area may cause harmful interference, in which case the user will be responsible for correcting any interference.

1.4 Note

Definitions

Definition Qualified service technicians or Qualified technicians : Persons having appropriate technical training and experience nec-

essary to be aware of hazards to which they are exposed in performing a task and of measures to minimize the danger to themselves

or other persons.

Extra Safety manual

Read also safety instructions in separate manual (R5976125).

6R5976698 BARCO GALAXY WARP™ 10 HB 05/04/2004

Tabla de contenidos

Otros manuales de Proyector DLP de Barco

Barco

Barco MSWU-81E Guía del usuario

Manuales populares de Proyector DLP de otras marcas

LG CineBeam PH450U Manual de usuario

JVC

JVC LX-WX50 Manual de usuario

ViewSonic

ViewSonic PX725HD Manual de usuario

Panasonic

Panasonic et-jpc100bu Manual de usuario

ViewSonic

ViewSonic PJD7830HDL Manual de usuario

LG HW300A Manual de usuario

Marantz

Marantz VP-11S2 Manual de usuario

Panasonic

Panasonic PT-TW331RU Manual de usuario

ViewSonic

ViewSonic PJD7822HDL Manual de usuario

ViewSonic

ViewSonic PJD5353LS Manual de usuario

Panasonic

Panasonic PT-LW321U Manual de usuario

NEC

NEC NC1500C Manual de usuario

ViewSonic

ViewSonic LS800WU Manual de usuario

LG RD-JT90 Manual de usuario

LG PW600G Manual de usuario

ViewSonic

ViewSonic PJD6250L Manual de usuario

LG Minibeam UST Manual de usuario