DAR-04 Digital Audio Recording Software DAR-04 Digital Audio Recording Software
10 11
DAR-04 Digital Audio Recording Software 10
2. Enter the point in time you
wish to play, by date, hour
and minute.
3. In Continuous Minutes,
enter the time length
you wish to play
starting from the
point you selected on
step 2.
4. Press Listen and if the
selected time range was
found in the recordings,
you will get the following
message:
Upon pressing Accept,
the reproduction will start
automatically.
NOTE 1: Follow the same procedure with the other audio inputs.
NOTE 2: If the time range was not found in the recordings, you will get an error message.
Recording schedule confi guration
Select the DAR for which you wish to set up the recording
schedule. In the Recording Schedule frame enter the upper
and lower limits of the recording time range.
NOTE:
Once you set a recording time range for a DAR, it will remain as its default confi guration
even after it is turned off.
Manual download of recordings
It is possible to download recordings from
one or more audio inputs at a time. Select
the audio inputs you wish to include in the
download by clicking on the check box Inp
(see fi gure on the right).
The downloaded audios are saved in the folder C:\DARaudios. Inside that folder, the fi les are
distributed in subdirectories by Input device, Year, Month, Day and Hour.
Download
Downloads the entire collection of recorded audios that have not been previously downloaded.
This procedure checks for already saved fi les and omits those during the download.
By Range
Downloads the recorded audios belonging to a
specifi c period of time.
Upon starting the download By Range, the frame
Select Time Frame gets enabled. Enter upper and
lower limits of the time range to download.
NOTE: During any download procedure the interface gets disabled to prevent breaking the
connection to the DAR and interrupt the download.
Automatic backup
If you wish to schedule a daily automatic backup of the
recordings, in the frame Automatic Download, click on the check
box Enable.
Enter the time at which the backup will start every day; the
program allows to schedule the backup only between 18 to 23 hr,
as it is the recommended time frame for such procedures.
If you wish to program a backup of recorded audio belonging to
a specifi c time range, click on the check box Download Range and
DAR-04 Digital Audio Recording Software 11
enter upper and lower limits of the range; otherwise (if Download Range is left unchecked),
the program will automatically save a backup of the last 24 hours.
If you wish to check the report of performed backups, open the fi le BackupHistory.txt located
in C:\DARaudios.
NOTE 1: Scheduled backups will download everyday, as long as the software is running.
NOTE 2: Once you hit Save Confi guration, the automatic backup confi guration will be saved in
the computer and it will load upon starting the program.
Playing recorded audios already saved in the computer
Downloaded audios are saved by the program in
C:\DARaudios; from that location, you can play
the audios by going to Play Downloads in the
menu bar.
You will then get a pop-up window where you can enter the minute you wish to play (see
fi gure below). For playing an entire hour, starting from the hour you entered, hit Play an Hour
(A); at any time during the reproducing you can pause, stop or go forward/backwards by
using the audio player’s controls (B)).
B
A
TECHNICAL SPECIFICATIONS
Input voltage 110 VDC
Maximum audio input devices 4
LAN connection outlet UTP connector RJ 45
Dimensions 21.5 x 15 x 4.5 cm 8.5’’ x 5.9’’ x 1.8’’
B&G ELECTRONICS
ONE YEAR LIMITED WARRANTY
BYG Electrónica S.A.S. guarantees that this product leaves the factory free from defects related to
materials and manufacturing. If a failure related to materials and manufacturing were to occur during the
period of one year after the date of purchase, BYG Electrónica S.A.S. would repair or replace the failing
equipment free of charge.
This warranty shall be voided if the product is modifi ed, tampered with, misused, or subjected to abnormal
working conditions. This warranty does not cover physical damage to the product surface. This warranty
does not apply when the malfunction results from the use of this product in conjunction with accessories,
other products, or peripheral equipment not designed by BYG Electrónica S.A.S.
