B&C IC-1355 Manual de usuario

Ironer

IC-13 Series Installation and Operation Manual

July 25, 2017

Revision 1.0

Contents

1 Important Safety Information 1

1.1 FORYOURSAFETY-CAUTION! ............................. 1

2 Important Instructions 2

2.1 BeforeAttemptingRepairs.................................. 2

2.2 PartsOrderingInformation ................................. 3

2.2.1 NameplateLocation ................................. 3

2.3 KeySymbols.......................................... 3

2.4 SafetyInformation ...................................... 3

2.5 Installation and Operational Safety Instructions . . . . . . . . . . . . . . . . . . . . . 5

3 Installation 7

3.1 InstallationNote........................................ 7

3.2 ReceivingInspection ..................................... 7

3.3 ElectricalInstallation ..................................... 8

3.4 GasConnection ........................................ 9

3.4.1 GasSupplyLine ................................... 9

3.4.2 Gas Supply Connection Requirements . . . . . . . . . . . . . . . . . . . . . . . 10

3.5 ExhaustRequirements .................................... 11

3.6 FreshAirRequirements ................................... 12

3.7 HandlingandUnpacking .................................. 13

3.8 RoomRequirements ..................................... 14

4 Operation 15

4.1 HeatCircuitOperationTest ................................. 15

4.2 InitialStartup ......................................... 16

4.3 UserSafety........................................... 17

4.4 HeatingSystemSafety .................................... 17

4.5 WorkingPrinciple....................................... 17

5 User Instructions 18

5.1 DailyUse............................................ 18

6 Easy Control 20

6.1 Introduction .......................................... 20

6.2 UserInterface ......................................... 20

6.3 MachineUse.......................................... 21

6.3.1 StartingtheMachine................................. 21

6.3.2 ShutDownProcedure ................................ 21

6.4 IroningSpeedControl .................................... 22

6.5 Heating............................................. 22

6.5.1 Electrical Heating Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.5.2 GasHeating...................................... 23

6.5.3 Progamming the Working Temperature . . . . . . . . . . . . . . . . . . . . . . 23

6.6 AlarmMessages........................................ 24

6.6.1 AL1 - Insufﬁcient Airﬂow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.6.2 AL4-FanThermalRelay .............................. 24

6.6.3 AL5-InverterFault ................................. 25

6.6.4 AL6-FlameFailure ................................. 25

6.6.5 AL7 - Overheat / Temperature Probe Fault . . . . . . . . . . . . . . . . . . . . 26

6.7 ProgrammingParameters .................................. 26

6.7.1 Temperature Measurement Unit . . . . . . . . . . . . . . . . . . . . . . . . . . 27

6.7.2 MaximumTemperature ............................... 28

6.7.3 OperatingTemperature ............................... 28

6.7.4 TemperatureRegulation............................... 28

6.7.5 StopTemperature................................... 29

6.7.6 HeatingType ..................................... 29

6.7.7 Number of Resistor Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

7 Maintenance 31

7.1 Warranty............................................ 31

7.2 RoutineMaintenance..................................... 32

7.2.1 Cleaning........................................ 32

7.2.2 MaintenanceIntervals ................................ 32

7.3 Service&Parts ........................................ 35

7.3.1 Service......................................... 35

7.3.2 Parts .......................................... 36

8 Maintenance Instructions 37

8.1 ReplacingInfeedBelts .................................... 37

8.2 ReplacingIroningBelts.................................... 38

8.3 Replacing the Support Rollers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

8.4 ReplacingtheSideRollers .................................. 39

9 Basic Troubleshooting 41

9.1 Power Failure During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

9.2 OtherFaults .......................................... 41

9.3 Lengthy Out of Service Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

10 Decommisioning 43

A Gas Conversion Technique 44

iii

Chapter 1

Important Safety Information

1.1 FOR YOUR SAFETY - CAUTION!

WARNING: For your safety the information in this manual must be followed to minimize the

risk of ﬁre or explosion or to prevent property damage, personal injury, or death.

•Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or

any other appliance.

•WHAT TO DO IF YOU SMELL GAS:

–Do not try to light any appliance

–Do not touch any electrical switch; do not use any phone in your building.

–Clear the room, building or area of all occupants.

–Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

–If you cannot reach your gas supplier, call the ﬁre department.

•Installation and service must be performed by a qualiﬁed installer, service agency or the gas

supplier.

Contact your local gas supplier to obtain particular instructions in the event that a user smells

gas. Place this sheet and any other instructions obtained from your gas supplier in a prominent

location.

Chapter 2

Important Instructions

2.1 Before Attempting Repairs

Moving parts can cause serious injury or death. Before attempting repairs, follow proper shut-

down procedures, remove power, and allow the machine to fully cool before commencement of

service.

Safety is of primary concern with any maintenance or repair operation. If you are in any way

unsure of how to proceed with a repair or adjustment, consult this manual, a qualiﬁed mainte-

nance technician, your local distributor, or the B&C Technologies Technical Service Department at

850-249-2222.

Only trained and experienced personnel should attempt maintenance or repair work on this equip-

ment. Follow all safety procedures including lock-out/tag-out procedures carefully. Ensure that

any loose ﬁtting clothing or jewelry is tucked in or not worn to avoid being pulled into the ma-

chine. Remember, the machine has no brain - you must use your own.

Before attempting repairs, follow proper shutdown procedures, remove power, and allow the ma-

chine to fully cool before beginning service.

Never attempt to clean or service any area of the machine without removing power at the main

disconnect and allowing time for the machine to cool completely.

Read, follow, and obey these safety rules! The B&C Technologies Technical Service Department

is available to answer any questions you may have about the operation and servicing of your

machine. Please call with any questions or concerns about the operation of your machine.

2.2 Parts Ordering Information

If you require literature or spare parts, please contact your local distributor. If a local distributor

is unavailable, you may contact B&C Technologies directly at (850) 249-2222 for the name of your

nearest parts dealer.

For technical assistance in the United States, contact B&C Technologies:

(850) 249-2222 Phone

(850) 249-2226 FAX

[email protected]

www.bandctech.com

2.2.1 Nameplate Location

When contacting B&C Technologies about your equipment, please make note of the model and

serial number, located on the nameplate on the rear of the machine.

2.3 Key Symbols

Anyone operating or servicing this machine must follow the safety rules in this manual. Partic-

ular attention must be paid to the DANGER, WARNING, and CAUTION blocks which appear

throughout the manual and shown in ﬁgures 2.1 on page 4 and 2.2 on page 4.

2.4 Safety Information

Installation Notice: For personal safety and for proper operation, the machine must be grounded

in accordance with state and local codes and in the USA in accordance with the National Electric

Code, article 250-96. Elsewhere, the equipment should be grounded in accordance with ANSI/NFPA

70, or the Canadian Electrical Code, CSA C22.1. The ground connection must be to a proven earth

ground, not to conduit or water pipes.

Figure 2.1: Key Symbols

Figure 2.2: Key Symbols

Natural Gas or Liquid Propane Gas (LP Gas) heated equipment installation must comply with

state and local codes, and in the USA, in accordance with the National Fuel Gas Code. Elsewhere,

the equipment should comply with ANSI Z22.1 or CSA B149.

Provisions must be made for adequate make-up air and ventilation, and access for equipment

service and installation.

2.5 Installation and Operational Safety Instructions

1. Read all instructions prior to operating this equipment.

2. Ensure that the equipment is properly grounded before applying power and operation be-

gins.

3. Do not process goods that have been previously cleaned in, soaked in, or exposed to gasoline,

dry cleaning chemicals, or any other ﬂammable or explosive materials, as they could catch

ﬁre or explode without warning, even after being washed.

4. Do not allow children to play in or around or operate this equipment.

5. Check the operation of all safety interlocks at the start of every shift. If the interlocks do not

stop the equipment immediately, the machine must be removed from service. Notify your

immediate supervisor, and do not operate the machine.

6. Never attempt to service the machine while it is running. Never reach over, under, around, or

behind any safety device, or into any area near moving parts or hot surfaces without shutting

off power and allowing the machine to adequately cool.

7. Read, understand, and follow all safety instructions. Do not come close to moving parts and

hot surfaces. Do not wear loose clothing, jewelry, neckties, or any other garment that could

become caught in the machine while operating or near the machine.

8. Only a qualiﬁed technician should attempt to service or repair the ironer.

9. Do not install the machine in an area where it could be exposed to water or weather.

10. Do not alter or tamper with the control system.

11. To reduce the risk of ﬁre, do not process plastics or articles containing foam rubber or simi-

larly textured rubber-like materials.

12. Keep the area near the exhaust ducting clean and free of lint, dust, dirt or debris.

13. Keep the interior and exterior of the machine clean of lint, dirt, dust and debris. The inte-

rior of the machine, along with the exhaust ductwork should be periodically inspected and

cleaned to avoid potential ﬁres (lint is highly ﬂammable).

14. Improper installation, operation and maintenance of this machine can cause exposure to sub-

stances in the fuel or from combustion that can cause serious illness or death. The machine

must be exhausted to the outside.

15. Always disconnect the electrical service from the machine and allow it to cool before per-

forming service.

16. This machine must be installed according to the installation instructions. All exhaust, elec-

trical connections, and gas or steam connections must comply with state and local codes and

must be made by a licensed installer where required.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hierro de B&C

B&C

B&C IC-20 Series Manual de usuario

Manuales populares de Hierro de otras marcas

Clatronic

Clatronic DB 3703 Manual de usuario

TEFAL

TEFAL FV4093Z0 Manual de usuario

Gorenje

Gorenje SIH 2200 BS Manual de usuario

Philips

Philips GC6012 Manual de usuario

Bosch

Bosch 2 Series Manual de usuario

Riffel

Riffel Catena KB-819 Manual de usuario

Texi

Texi Hestia Manual de usuario

Maxwell

Maxwell MW-3010 Manual de usuario

TREVIDEA

TREVIDEA Girmi ST60 Manual de usuario

Philips

Philips HI5914/30 Manual de usuario

Primula

Primula Vapormat Manual de usuario

Magio

Magio MG-541 Manual de usuario

Scarlett

Scarlett SC-1334S Manual de usuario

Bosch

Bosch Sensixx B22L Manual de usuario

Philips

Philips GC651 Manual de usuario

Vitek

Vitek VT-1247 VT Manual de usuario

Cleanmaxx

Cleanmaxx 3397 Manual de usuario

Philips

Philips GC800 Manual de usuario