Bali SRGF11610 Manual de usuario
Questions, problems, missing / replacement parts? Before returning to your retailer,
call our customer service department at 1-866-814-0585, 8 a.m. - 8 p.m., EST
Monday-Friday.
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or fire department.
Do not store or use gasoline or
other flammable vapors and liquids
in the vicinity of this or any other
appliance.
DANGER
WARNING
WARNING: For Outdoor Use
Only.
CAUTION:
Installer: Leave the instruction manual
to the user for future use.
Consumer: Please keep this manual
for future reference.
Read the instructions before use. This
appliance must be installed in accordance
with such regulations as are in force.
Owner’s Manual
An LP-cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
36" Square Gas Fire Pit
Model#SRGF11610
TM
36'' Gas Fire Pit
SRGF11610
50,000 BTU/HR
LP
20-lb. LP - gas cylinder
2.18 mm
s Do not try to light the appliance.
s Do not touch any electrical switch; do not use any phone in the vicinity of this product.
s Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
s If you cannot reach your gas supplier, call the fire department.
WARNING
CARBON MONOXIDE HAZARD
: Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Read the installation, operation and
maintenance instructions thoroughly before installing or servicing this
equipment.
WHAT TO DO IF YOU SMELL GAS?
Installation and service must be performed by a qualified installer, service agency or gas
supplier.
PRECAUTIONS
This appliance can produce carbon monoxide which has
no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such
as a camper, tent, car or home.
2
IMPORTANT SAFETY INFORMATION
tThe installation must comform with local codes or, in the absence of local codes, with
the CAN/CGA-B 149.2, Propane Installation Code.
tAlways place the appliance on a firm and level surface.
tDo not burn solid fuels in this gas appliance.
tUse the appliance outdoors in a well-ventilated space only, not in a building, garage, or any other
enclosed area.
tWhen using the appliance, keep the appliance area clear and at least 50 inches from combustible
materials, gasoline and other flammable liquid and vapors. Certain items or materials, when stored
under the appliance or nearby, will be subjected to radiant heat and could be seriously damaged.
t
Inspect the gas connections of appliance prior to each use. Do not operate the unit if there is gas leak.
A qualified service person should inspect the appliance annually.
tAlert children and adults to the hazards of high surface temperatures and keep them away
to avoid burns or clothing ignition.
tCarefully supervise children and pets when they are near the appliance.
tReplace and guard or other protective device removed for servicing.
tDo not hang clothing or other flammable materials on or near the appliance.
tDo not use the appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and to replace any part of the control system and any gas
control which has been under water.
t
t
Use only a cylinder supply system arranged for vapor withdrawal, and the cylinder must include a
tThe LP-gas supply cylinder to be used must be: Constructed and marked in accordance with the
Specifications for LP-gas cylinders of the U.S. Department of Transportation (DOT); or the Standard
for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission,
CAN/CSA-B339, as applicable;
The LP-gas supply cylinder to be used must be provided with a listed overfilling prevention device;
and provided with a cylinder connection device compatible with the connection for the appliance.
collar to protect the cylinder valve.
tThis appliance requires 20 lb (9 kg) LP gas supply cylinder.
tThe burner must be replaced prior to the appliance being put into operation if it is evident that the
burner is damaged. The replacement burner shall be that specified by the manufacturer.
tInstallation and repair should be done by a qualified service person. The appliance should
be inspected before use and at least annually by a qualified service person. More frequent
cleaning may be required as necessary. It is imperative that control compartment, burners,
and circulating air passageways of the appliance be kept clean.
WARNINGS AND CAUTIONS
3
This appliance is designed to operate with a standard 20 Ib propane cylinder with Approved
Cylinder Connection.
WARNING:
This product can expose you to chemicals including lead, which is known to the State of
California to cause cancer, and carbon monoxide, which is known to the State of California to
cause birth defects or other reproductive harm. For more information, go to:
www.P65Warnings.ca.gov.
NOTE: PLEASE READ THE FOLLOWING SAFETY RULES:
Before beginning assembly of product, make sure all parts are present. If any part is missing or
damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
Perform a leak test with a soapy solution:
1. To check gas connections.
2. After connecting a new cylinder.
3. Upon re-assembly after disassembly.
WARNINGS AND CAUTIONS
PREPARATION
TOOLS NEEDED: (NOT INCLUDED)
Philips screwdriver
Adjustable open end wrench
Estimated time for assembly: 40 minutes.
4
A
O
N
M
L
K
J
I
B
C
D
E
F
G
H
EXPLODED VIEW
5
AA
BB
CC
DD
EE
FF
Parts Description Quantity Picture
PARTS & HARDWARE
M6x20 Bolt
M4x25 Bolt
M4x12 Bolt Assembly
D6 Washer
D5 Washer
M5 Nut
30Pcs
4Pcs
8Pcs
1Pc
4Pcs
1Pc
Lid handle
Fire bowl lid
Burner assembly
Table top panel
Right panel
Front panel
Sliding track
ytitnauQnoitpircseDtraPA
B
C
D
E
G
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
2 pcs
F
Caster
Cylinder clamp screw
Stator
Cylinder holder assembly
Left panel
Rear panel
ytitnauQnoitpircseDtraPH
I
J
K
L
M
N
O
2 pcs
1 pc
2 pcs
1 pc
1 pc
1 pc
1 bag
1 pcLimited strip
Lava rocks/ glass chips
6
G
E
N
AA
GN
Choose a flat place to assemble the product, pad a
cardboard to protect the table surface.
20
AA M6x20 Bolt 16Pcs
AA M6x20 Bolt 6Pcs
Attach the right panel (F) and limited strip (O)to the
front panel (G) & rear panel (N) with 6 M6x20mm bolts
(AA) (Fig. 2)
O
N
G
F
AA
ASSEMBLY INSTRUCTIONS
7
Step 3
Hardware Used
Fig. 3
Step 4 Fig. 4
AA M6 x 20 Bolt 8Pcs
CC M4 x 12 Bolt Assembly 8Pcs
IL
L
K
L
J3
20
two
20
M
M
I
ML
K
AA
AA
AA
L
H
J
CC
H4
two stators
with 4
ASSEMBLY INSTRUCTIONS
8
5Fig. 5
6Fig. 6
L
H5end (locking position).
MLH
Place the burner assembly (D) onto the table top panel (E) .
Attach two parts with 4 M4 x 25 bolts (BB), 4 D5 washers (EE).
The control panel on the burner assembly (D) should fit the
position on the front panel (G).
6
D
E
EEEBB
BB M4x25 Bolt 4Pcs
EE D5Washer 4Pcs
G
ASSEMBLY INSTRUCTIONS
9
Place lava rocks/ glass chips (C) (Max. 5.5 lbs) onto the
burner assembly (D). (Fig.7)
C
D
7Fig. 7
8Fig. 8
Insert the lid handle (A) through fire bowl lid (B) and attach
it with the D6 washer (DD) and M5 nut (FF). Place the fire
bowl lid (B) onto the table top panel (E) when not use. (Fig.8)
A
B
B
E
FF
DD
DD D6Washer 1Pc
FF M5 Nut 1Pc
ASSEMBLY INSTRUCTIONS
10
Tabla de contenidos
