Balcrank 1300-001 Manual de referencia

Tabla de contenidos

Otros manuales de Bomba de agua de Balcrank

Balcrank

Balcrank GIANT JET 1130-008 Manual de instrucciones

Balcrank

Balcrank 1120-015 Manual de instrucciones

Balcrank

Balcrank TIGER 500 Manual de instrucciones

Balcrank

Balcrank 1120-011 Manual de instrucciones

Balcrank

Balcrank Lynx Series Manual de instrucciones

Balcrank

Balcrank 1120-012 Manual de instrucciones

Balcrank

Balcrank JET POWER 1150-004 Manual de instrucciones

Balcrank

Balcrank Lynx Manual de instrucciones

Balcrank

Balcrank Lynx Series Manual de instrucciones

Balcrank

Balcrank BOBCAT 130 Series Manual de instrucciones

Balcrank

Balcrank Tiger HP 1130-019 Manual de instrucciones

Balcrank

Balcrank 1120-014 Manual de instrucciones

Balcrank

Balcrank Lion 600 Manual de funcionamiento

Balcrank

Balcrank LION 350 Manual de funcionamiento

Balcrank

Balcrank LION HP 1151-022 Manual de instrucciones

Balcrank

Balcrank Lion HP 1150-015 Manual de instrucciones

Balcrank

Balcrank PANTHER 1150-006 Manual de instrucciones

Balcrank

Balcrank PANTHER 1130-011 Manual de instrucciones

Balcrank

Balcrank 1300-027 Manual de instrucciones

Balcrank

Balcrank PANTHER HP Series Manual de instrucciones

Balcrank

Balcrank BOBCAT 130 Series Manual de instrucciones

Balcrank

Balcrank 1170-002 Manual de instrucciones

Balcrank

Balcrank BOBCAT 300 Series Manual de instrucciones

Balcrank

Balcrank CF10 Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario

SERVICE BUTTETIN SB1054

REV. B 2/03

Thoroughly read and understand this manual before

installing, operating or servicing this equipment.

OPERATION, INSTALLATION,

MAINTENANCE AND REPAIR GUIDE

BARREL PUMP

MODEL #1300-001

ITEM PART# DESCRIPTION

A 822519 Bushing, Compression

B 822520 Seal

C 820180 Gasket, Molded

D 820178 Base Assembly

E 820827 Piston Sub Assembly

F 820829 Rings, Brass (2)

G 820184 Tube Section Assembly

H 822275 Seal

®

Balcrank®Corporation

Weaverville, NC 28787

800-747-5300

800-763-0840 Fax

www.balcrank.com

SERVICE BULLETIN SB1054

REV. B 2/03

822101

PARTS LIST AND INSTRUCTIONS FOR ASSEMBLING AND OPERATING

HEAVY DUTY BARREL PUMP MODEL #1300-001

1. Screw the 822521 Spout into head, engaging threads until tight. If not properly aligned,

increase pressure to further tighten spout to correct position.

2. Insert the 820184 Tube Section Assembly into the 820178 Base Assembly of the pump and

tighten securely with a small pipe wrench to eliminate any air leaks. Do not use undue force

in tightening as the base or valve may be damaged.

3. Screw the pump into the threaded bung in the drum and tighten securely by grasping the

spout in one hand and the lever in the other hand.

NOTE: The 820184 tube suction assembly will automatically adjust to the proper position.

IMPORTANT: If when the pump is tightened into the drum bung and the spout is not in the

desired position above the drum, loosen the clamp bolt on base assembly and rotate pump

housing to the desired position and retighten.

4. Pull the piston rod of piston sub-assembly up and attach the operating lever to the piston rod,

using the rivet and retainer clip, enclosed in the envelope.

5. Start the pump by several quick strokes of the lever. If the pump fails to start, check Step 2.

6. If the pump fails to start, and Item 2 has been checked, remove the pump from the drum

and check the 820184 Tube Suction Assembly to see that it is extended to reach the bottom

of the drum.

7. In as much as certain liquids have a tendency to build up a coating on the surface when

the pump is not in use.

8. If pump leaks around the 822519 compression bushing, tighten bushing by hand only.

NOTICE: This pump is made of steel. If it is used with uids that cause rusting, the rust

may interfere with the operation of the pump. Our guarantee does not cover any pump

showing rust.

Distributed by: