BAK Thermoplastic Welding Technology MION Manual de usuario
1
OPERATING INSTRUCTIONS
Automatic wedge welding machine MION
Please read the operating instructions carefully before use and keep for further reference!
APPLICATION
The MION is an automatic hot wedge welding machine for overlap welding and for
manufacturing of films and geomembrane liners in tunnels as well as in earthwork and civil
engineering.
Overlap max. 95mm
Type of seam Welding seams are produced in accordance with DVS 2225 part I
Other dimensions of seams are possible on request.
Type of wedge In standard version the MION is supplied with a ceramic wedge.
This allows welding of all different kind of material without
changing the wedge.
2
SECURITY WARNING
Danger! Unplug the tool before opening it as live components
and connections are exposed.
Danger of fire and explosion in case of incorrect use of the hot
wedge welder, especially near combustible materials and/or
explosive gases.
Danger of burns Do not touch the hot wedge when hot, allow the
tool to cool down.
Connect the tool to a socket outlet with protective earth conductor.
Any interruption of the protective earth conductor within or outside
the tool is dangerous!!! Use only extension cables with a protective
earth conductor!
The voltage rating stated on the tool should correspond to the
mains voltage.
For personal protection, we strongly recommend to connect the tool
to a RCCB(Residual Current Circuit Breaker)before using it on
construction sites.
The tool must be operated under supervision.
Radiant heat from the hot wedge can ignite flammable materials.
Protect the tool from damp and wet.
TECHNICAL DATA Tool with protection of class I
Voltage V~ 230 or 120V
Power consumption W 850
Frequency Hz 50/60
Temperature °C 20 - 520
Welding pressure N max. 1000
Drive m/min. 0.8 –3.2
Size LxWxH mm 200 x 200 x 210
Weight kg 5.5
3
OPERATING
1 Motor button (green) 5 Up ward button
2 Motor LED (green) 6 Heating button (red)
3 Status LED (yellow) (plus button 5 = Heating on/off)
4 Heating LED (red) 7 Down ward button
OPERATING LEVEL
Change value with buttons 5 and 7
Forward to next level with the red button.
This message only shows up when the recommended service time is reached. Confirm with
the red button.
Standard display to adjust the parameters.
Speed adjustment
Motor Start/Stop with green button.
The green LED shows you the condition.
4
Standard display to adjust the parameters.
Temperature adjustment
Press the red button, beside the set-temperature appears a X. Now adjust the temperature.
To switch on the heating press the red and the up ward button together, the red LED is
flashing up until the temperature is reached.
Switch off the heat with pressing this two buttons together.
ADJUSTMENT LEVEL
To reach adjustment level
Press the up- and down ward buttons together for approx. 5 seconds.
Change value with the up- and down buttons.
Forward to the next level with the red button. It shows serial number and working hours
(can’t be changed).
5
Maximum speed tolerance to alarm.
Maximum temperature tolerance to alarm.
Alarm signal on / off
Choice of display
°C- m/min.
°F -ft/min.
Adjustment of language
German –English –Spanish
6
Don’t save parameter = EXIT
Save parameter = SAVE
Menu end with the red button
Pressure adjustment –DON’T HEAT UP THE WEDGE!!
Engage and position the welding tool onto the material to be welded. Pull the toggle lever (10).
By rotating the adjustment screw (5) the drive/pressure rollers will lightly touch the material to
be welded, in this way you will define the POINT ZERO(0) N of pressure. Set the desired
pressure by rotating the adjustment screw (5), to every single step of rotation you will set 65N of
pressure on seam. Lock the desired pressure with the locking screw (16)
.
Warning: If the maximum welding pressure (1000 N) is exceeded, mechanical damage may
occur.
DESCRIPTION OF MACHINE
7
1Buttonincrease 9 LEDmachineon
2Buttondecrease 10 Togglelever
3ButtonDriveon/off 11 Lowerpressureroller
4ButtonHeatingon/off(togetherwithbutton1) 12 Upper pressureroller
5Pressure adjustment screw 13 Guide handle (optional)
6Main switch 14 Heater cartridge
7LED Motor (on/off alarm) 15 Handle
8LED Heating (on/off alarm) 16 Locking screw
MAINTENANCE
Clean the hot wedge with a wire brush at the end of a working day.
Clean the drive/pressure rollers with a wire brush.
As required, treat the chain with a suitable spray.
After use, always check the mains cable and the plug to ensure that they are not damaged.
SERVICE AND REPAIR
The welding machine should be checked by an authorised service centre approx. every 1000
hours of running time.
Inspections and repairs have to be executed exclusively by BAK authorised service centres.
GUARANTEE AND LIABILITY
For BAK guarantee and liability see the general and sales conditions on the back of the invoice
paper.
BAK Thermoplastic Welding Technology rejects any guarantee claims for tools which are not in
original condition.
Technical data are subject to change without prior notice.
Tabla de contenidos
Otros manuales de Sistema de soldadura de BAK Thermoplastic Welding Technology
BAK Thermoplastic Welding Technology
BAK Thermoplastic Welding Technology MION II Manual de usuario
BAK Thermoplastic Welding Technology
BAK Thermoplastic Welding Technology Laron BL digital Manual de usuario
BAK Thermoplastic Welding Technology
BAK Thermoplastic Welding Technology LARON Version 2 Manual de usuario
Manuales populares de Sistema de soldadura de otras marcas
TAFA
TAFA 30*8B35 Manual de usuario
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manual de usuario
ESAB
ESAB Buddy Arc 145 Manual de usuario
CIGWELD
CIGWELD 636804 Guía rápida
Red-D-Arc
Red-D-Arc DC-400 Manual de usuario
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario
