Bacharach H25-IR Manual de usuario

These instructions describe how to replace the IR Sensor in the H25-IR Infrared Gas Leak Detector.

It is assumed that the user is familiar with the operation and menu system of the H25-IR. If necessary, refer to

Instruction 3015-4342 or 3015-5286 (dependent on generation of model) for detailed operation and

maintenance information.

Items Required:

Replacement IR Sensor Kit:*

Model Bench Kit Solo Bench (450 mW)** Solo Bench (540 mW)**

CFC, HCFC, HFC &

Halogen gases 3015-4501 3015-5086 -

R600 3015-4502 - 3015-5089

SF63015-4561 3015-5087 -

CO23015-4562 3015-5090 -

** Not for individual sale. Used for ID purposes only. (i.e. To order replacement kit for your bench which is

labeled model number 3015-5086, place order for kit number 3015-4501.)

Medium Phillips head screwdriver

Small flat blade screwdriver

Wire cutter (for removing cable ties)

Kit contains IR Sensor of gas being detected, cable ties (Qty. 2), and this instruction sheet

Top Cover Removal

1. Remove both the front and rear bezels by first disengaging the plastic tabs on the right and left sides of

the bezel, and then pulling the bezel straight out.

2. Remove the two top screws that secure the front panel.

3. Remove the four screws that secure the rear panel.

4. Remove all rear panel electrical connectors.

5. Drop down the rear panel far enough to allow the top cover to clear, being careful not to stress the

cables attached to the panel.

6. Remove top cover by sliding it toward rear of instrument.

Figure 1.

H25-IR

IR Sensor Replacement

Instruction 3015-4526

Rev. 7 – August 2010

www.netzerotools.com

Installing the New IR Sensor

7. Carefully remove tubing and electrical connectors from old IR sensor. See Figure 2.

8. Cut off two cable ties that secure IR sensor to chassis, and remove sensor from instrument.

9. Place new IR sensor inside chassis, positioning its 10-pin electrical connector toward the rear of the

instrument. Rotate the sensor so that its gas inlet and outlet fittings and its electrical connectors are

positioned as shown in Figure 2.

10. Remove protective caps from the gas inlet and outlet fittings of the new IR sensor.

11. Connect the 12-conductor ribbon cable from IR SOURCE connector J5 on main board to IR sensor

emitter connector (front of instrument).

12. Connect the 10-conductor ribbon cable from DET connector J6 on main board to IR sensor detector

connector (rear of instrument).

13. Using the two supplied cable ties, secure the IR sensor to the chassis by threading each cable ties

through its cable-tie mount; around the foam insulation that surrounds the IR sensor; and around the

12-conductor ribbon cable. Cut off the cable-tie excess.

14. Connect tubing from pump to the IR sensor gas inlet fitting, and connect the IR sensor gas outlet fitting

to the instrument’s exhaust port as shown below.

IR SENSOR

Figure 2.

www.netzerotools.com

IR Emitter Adjustment

WARNING! SHOCK HAZARD. When performing the following step, be careful not to come in contact

with AC voltages when working inside the instrument with the cover off and AC voltage applied.

15. Reconnect the AC power cord, and then turn the instrument ON while holding down the front panel ENT

button to enable the Factory menu

16. Wait until the instrument warms up and the Data Display screen appears before proceeding.

17. Press the ENT and ESC buttons simultaneously to access the Main menu. From the Main menu, select

DIAGNOSTICS > IR EMITTER to display the IR Emitter Parameters screen.

18. If the R37 potentiometer is present on your generation of the H25-IR, adjust it clockwise to a reading of

450 ±20 mW or 540 ±20 mW (R600 model only), corresponding to the version of the part as seen in

the items required section of this manual containing the part numbers. If your generation of the H25-IR

does not have an R37 potentiometer, the IR Emitter power can be adjusted by pressing the

VOL/RANGE (higher/lower adjustment in small increments) or SETUP/MODE (higher/lower adjustment

in larger increments) buttons on the front of the unit.

Figure 3.

DIGIPOT Adjustment

19. Press ESC twice to return to the Main menu. From the Main menu, select FACTORY > DIGIPOT to

display the DIGIPOT screen.

IMPORTANT! When performing the following Step, the instrument must be sampling fresh air

(zero gas) when adjusting the DIGIPOT value.

20. Use the Up and Down buttons to adjust the DIGIPOT value until the IR VOLT reading is

4.2000 ±0.0500 volts. Press ENT to save the new DIGIPOT value.

IMPORTANT! If adjusting the DIGIPOT does not reach 4.20000±volts then return to step 18 to lower

the IR Emitter setting. If the IR Emitter setting is 450±mW adjust the IR Emitter setting

to 375±mW. Next, repeat the DIGIPOT adjustment.

21. Turn OFF instrument and remove AC power cord.

22. Reassemble instrument.

IR EMITTER PARAMETERS

VOLTS=5.7345 mA=77.5

OHMS=75.0 mW=450.0

DIGIPOT=220

IR VOLT=4.2000

NOTE:

Your readings for the other

parameters on this screen may vary.

www.netzerotools.com

Factory Calibration

NOTE: Factory calibration establishes the instrument’s default calibration setting that is recalled when

“RESTORE FACTORY CAL” is selected from the CAL DATA menu.

23. With all covers in place, turn the instrument back ON while holding down the front panel ENT button to

enable the Factory menu.

IMPORTANT: Before calibrating, allow the instrument to warm up for at least 15 minutes.

24. Perform an internal calibration as described in the H25-IR instruction manual, 3015-4342.

25. After the instrument has been calibrated, store the flow and pressure calculations of that calibration as

the default factory calibration values as follows:

a. Press the ENT and ESC buttons simultaneously to access the Main menu. From the Main menu,

select FACTORY > SENSOR CAL > FLOW RATE to display the Flow Rate and Pressure screen:

b. INT: This line shows the flow rate in moles/minute for both the Search and Measure modes after

performing a calibration using the internal leak source, along with showing the manifold’s pressure

drop.

FAC: This line shows the flow rate and pressure drop values that are currently stored as the default

factory calibration values. These values are used to validate calibrations performed by the user. A

calibration error will occur if the user’s calibration and factory values differ by more than 20%.

c. Press ENT to store the internal calibration numbers as the default factory calibration values.

d. Press ESC until the Data Display screen appears.

26. This completes replacing the IR Sensor.

S-Mpm/dP M-Mpm/dP

INT 0.0177/-1.33 0.0100/-2.28

FAC 0.0177/-1.33 0.0100/-2.28

ENTER TO SAVE INT AS FACTORY

www.netzerotools.com

Otros manuales para H25-IR

Tabla de contenidos

Otros manuales de Detector de gas de Bacharach

Bacharach

Bacharach MGS 550 Manual de usuario

Bacharach

Bacharach MGS-400 Manual de usuario

Bacharach

Bacharach Leakator 10 Manual de usuario

Bacharach

Bacharach MGS-350 Manual de usuario

Bacharach

Bacharach GDA-1600 Manual de usuario

Bacharach

Bacharach IAM-100 Manual de usuario

Bacharach

Bacharach MVR-300 Manual de usuario

Bacharach

Bacharach HGM300 Manual de uso y cuidado

Bacharach

Bacharach Leakator 10 Manual de usuario

Bacharach

Bacharach H25-IR PRO Manual de usuario

Bacharach

Bacharach HFO1234ZE Manual de usuario

Bacharach

Bacharach MGS-410 Manual de usuario

Bacharach

Bacharach MGS-400 Manual de usuario

Bacharach

Bacharach MGS-460 Manual de usuario

Bacharach

Bacharach MGS 550 Manual de usuario

Bacharach

Bacharach Leakator 10 Manual de usuario

Bacharach

Bacharach Multi-Zone 3015-6143 Manual de usuario

Manuales populares de Detector de gas de otras marcas

Macurco

Macurco GD-6 Manual de usuario

Evikon

Evikon E2632 Manual de usuario

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Manual de usuario

MSA

MSA altair 5 Manual de usuario

DOD Technologies

DOD Technologies ChemLogic CL96 Manual de usuario

DEGA

DEGA NS III LCD Series Manual de usuario

RKI Instruments

RKI Instruments 35-3001A-08-01 Manual de usuario

PEMTECH

PEMTECH PT2008 Series Manual de usuario

Coster

Coster RGS 328 Manual de usuario

Sygonix

Sygonix 2483186 Manual de usuario

Perry

Perry 1GA 50917MET/P Manual de usuario

isweek

isweek AS8900 Manual de usuario

Oldham

Oldham OLC 10 Manual de usuario

Wizmart

Wizmart NB983 Manual de usuario

Beacon

Beacon MEGA Manual

RKI

RKI GX-6000 Manual de usuario

Dräger

Dräger PIR 7000 Manual de usuario

GDS

GDS GASMAX EC Manual de usuario