Baby Brezza Formula Pro Advanced WiFi Manual

Instructions

for set-up, use and cleaning

Please read fully to ensure your Formula Pro® Advanced WiFi works properly every time.

Customer Service

If you are experiencing problems with your Baby Brezza Formula Pro®Advanced WiFi,

please call Baby Brezza Customer Service at 1-888-396-6552 or email cs@babybrezza.com

before returning the product to the store you purchased it at so that we can oer you our best service

customized to your particular situation.

babybrezza.com

The limited warranty is valid only on products bought through authorized resellers and used in the

United States & Canada. Buying through an unauthorized reseller or using this product outside of the

United States and Canada automatically voids this warranty.

This warranty is available to consumers only. You are a consumer if you own a Baby Brezza Formula

Pro® Advanced WiFi that was purchased at retail for personal, family or household use. Except as

otherwise required under applicable state law, this warranty is not available to retailers or other com-

mercial purchasers or owners. We warrant that your Baby Brezza Formula Pro® Advanced WiFi will be

free of defects in material or workmanship under normal home use for one year from the date of

original purchase. Customer will be required to present original proof of purchase in order to obtain

the warranty beneﬁts. In the event that you do not have proof of purchase date, the purchase date for

purposes of this warranty will be the date of manufacture. If your Baby Brezza Formula Pro® Advanced

WiFi should prove to be defective within the warranty period, we will repair it or, if we consider it

necessary, replace it.

To obtain warranty services, please call Customer Service at:

1-888-396-6552, cs@babybrezza.com

or write to:

Baby Brezza, 250 Passaic Street, Newark, NJ 07104 Attn: Customer Service.

Limited 1-Year Warranty

This product may be covered under one or more of the following including U.S. Patent No. 8,584,901, Canada Patent

No. 2,842,603, China Patent No. CN103874441, Australia Patent No. 2011374309,

Spain Patent No. ES2473790B2 and pending patent application(s)

in the U.S. and other countries.

TECHNICAL DATA Model: FRP0066

Supply Voltage: 120V ~ 60Hz

Current: 2.5A

Heater Power: 260W

• Get a cup or bottle larger than 10oz and place it under the funnel.

• Press the“ounce” button on the control panel repeatedly until the LCD screen says“10oz”.

• Now press the“water only” button on the control panel. The Formula Pro® Advanced WiFi will dispense 10oz of water.

• Dispose of the water dispensed, or use it to water your plants.

Attention: Don’t take anything apart yet.

Follow these steps before doing anything else.

Now let’s rinse the inside of the machine.

Now you can turn o and unplug the machine,

remove all the parts shown on the next page and

set-up your new Formula Pro® Advanced WiFi

Save these instructions

IMPORTANT SAFEGUARDS

1. Read all instructions before using.

2. Do not touch hot surfaces.

3. To protect against electric shock and injury to persons, do not immerse cord, plug, or appliance in water or other liquid.

4. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of

experience and knowledge, unless they are closely supervised and instructed concerning use of the appliance by a person responsible for

their safety. Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they

do not play with the appliance.

5. Turn o and unplug the appliance from the outlet when not in use, before assembling or disassembling parts and before cleaning.

To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.

6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner.

Contact the manufacturer at their customer service telephone number for information on examination, repair, or adjustment.

7. The use of accessory attachments not recommended by the appliance manufacturer may cause re, electric shock or injury.

8. Use on level surface and be sure there is no debris under the unit and the rubber wheels are touching the surface.

9. Household use only. Do not use outdoors.

10. Do not let cord hang over edge of table or counter, or touch hot surfaces.

11. Do not place on or near hot gas or electric burner, or in a heated oven.

12. Do not use appliance for other than intended use.

13. Do not attempt to use the machine without water in the water tank.

14. This appliance has a polarized plug (one blade wider than the other). To reduce risk of electric shock, this plug is intended

to t into a polarized outlet only one way. If the plug does not t fully into the outlet, reverse the plug. If it still does not t,

contact a qualied electrician. Do not attempt to modify the plug in any way.

15. A short power-supply cord is provided to reduce risks of becoming entangled in or tripping over a longer cord. Longer

detachable power-supply cords or extension cords are available and may be used if care is exercised in their use. If using the

machine with an extension cord, make sure the cord is the proper electrical rating for the machine. The extension cord

should be arranged so that it does not drape over a counter top or tabletop, where it can be pulled on by children or

tripped over unintentionally.

16. Before serving make sure formula mixture is at safe temperature for baby.

17. Avoid contact with moving parts. Never remove powder container, powder container lid, funnel or water tank while

machine is in operation.

18. Please note that changes or modications of this product is not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment. Do not disassemble or open base of machine.

19. NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o & on,

the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

20. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

When using electrical appliances, basic safety precautions should be followed, including the following:

WARNING:

• Set-up & cleaning is critical to the function of your Formula Pro® Advanced. Please follow all instructions properly.

•Always use distilled or boiled water cooled to room temperature.

• Never pour boiling/hot water in water tank.

• Unboiled tap water and/or unsterilized baby bottles can potentially lead to adverse eects for the health

of your baby. Use puried water suitable for infant formula preparation.

• Only prepare one bottle at a time, feed immediately & follow all instructions carefully.

•Do not keep leftover formula mix. If your child was born premature, with low birth-weight or is immune decient,

please consult your pediatrician before using this machine.

• Place the Formula Pro® Advanced WiFi on the counter or other level surface and turn it around so the back is facing you.

• Remove the water tank from the back of the machine, wash it with warm soapy water and rinse thoroughly, then dry.

• Fill water tank with bottled water suitable for infant formula preparation, or boiled water, cooled to room temperature.

• Place water tank back on base, turn the machine around so the front is facing you and then plug it in. The machine

will turn on and the LCD screen will light up.

• The machine will beep once to tell you it’s powered on. You’ll also see the LCD display turn on.

• Get familiar with the part names on the next page, then proceed with the set-up on the App or the following pages.

Disassembly tip:

Powder Container Lid

Stirring Wheel

Locking Cover with Silicone Scraper

Measuring Wheel

Powder Container

Axle

Powder-Dispensing Hole

Control Panel

Base Power Cord

(on back - not shown)

Bottle Grate

Funnel

Water Tank

Funnel Cover

Drip Tray

Funnel Compartment

Using the App

App Home Screen

Formula Pro®Advanced WiFi - parts

Disassemble and wash all parts (except the base) and dry thoroughly.

Never clean the Powder Container

in a dishwasher, sterilizer or microwave!

To remove the Stirring Wheel, grasp it

as shown above & pull up while

holding the powder container down.

Download the Free Baby Brezza Formula Pro®App

Open the app on your mobile device, then follow the steps to register your Formula Pro Advanced® WiFi, create an account, and

connect the Formula Pro Advanced WiFi to your home network. After connecting to WiFi, you can set-up the machine,

set-up bottles and use the app to control the Formula Pro Advanced WiFi.

Selected bottle settings

Touch to dispense water only

App menu

Includes all instructions,

and other functions

Touch to edit bottle settings

Touch to select pre-set bottle

Touch to add a bottle pre-set

Touch to stop dispensing

Touch to dispense formula

Tip: Follow the set-up and cleaning instructions on the app or on

the following pages to use your Formula Pro® Advanced properly.

7 8

Formula Pro® Advanced WiFi set-up instructions

Now place the powder container on the base

with the printed markings facing you.

Now place the stirring wheel on the axle

and push down rmly until you hear a click.

Make sure the stirring wheel is snapped in

place and does not lift up easily.

Place the axle on the base as shown.

After hand washing these parts, make sure

they are all completely dry before assembly.

Assemble the funnel & funnel cover.

Then Insert funnel assembly into funnel

compartment by sliding it up, then in.

Make sure the locking cover & measuring wheel

look like this when assembled.

Place the measuring wheel into the powder

container, tting it over the axle with the at

side facing down.

Make sure the holes in the measuring wheel

are in the same position as shown above.

1. Place the front edge of locking cover

in the recess in the inside/front of the

powder container, UNDER THE TAB.

2. Fit hole in locking cover over top of axle.

It will not lay completely at.

IMPORTANT

Set-up and cleaning videos available at babybrezza.com/video.

click

3 4

Carefully pour formula powder into the

powder container. Wipe up any spilled

formula powder.

Make sure that the powder is lled between the

MIN & MAX lines on the powder container.

Place the powder container lid on the

powder container and turn clockwise

until it stops.

This will engage the safety switch & lock

the powder container onto the base.

To remove the powder container, turn the

lid counter-clockwise.

Fit the drip tray on the base to t your bottle

height. Adjust it so the mouth of the bottle is

as close to the funnel as possible.

Push the drip tray rmly against the base to

set it in place

You can use the app to make a bottle or

review the controls on the next page to make

a bottle with the buttons on the machine. .

Now you’re ready to add powder & make a bottle

Powder setting

button: Press to

select setting number

for your formula

brand and type

Water only button:

Press to dispense

ounces displayed

on LCD (selected by

the “ounce” button)

Temp button:

Press to select your

warming temperature

LCD Display:

Shows selected functions & warnings

Ounce button:

Press to select ounces

of water dispensed

Stop button:

Press to stop

dispensing

Start button:

Press to dispense

formula

Using the Formula Pro®Advanced WiFi control panel

= Slightly warmer than body temperature= Body temperature= Room temperature

Powder Lid Open - The powder container lid is not closed completely or is not on the powder container

correctly. Close the powder container lid completely and correctly when this symbol is illuminated.

Low Water - Rell water tank when this symbol is illuminated.

Clean Funnel - This symbol will illuminate after every 4 bottles are made. When this symbol is illuminated,

remove funnel assembly, wash, and dry completely, then place it back into the base. See Page 11 for details.

Funnel Out - Funnel is removed or not inserted completely. Make sure the funnel is pushed all the way in

when this symbol is illuminated.

Warning symbols

Temperature indicator symbols

Powder & water settings

Powder Setting Indicator - Use the“powder setting”button to chose your powder setting 1-10.

Ounce Indicator - Use the“ounce”button to chose how many ounces of water to mix with powder.

2, 3, 4, 5, 6, 7, 8, 9, 10 ounces of water are available. There is no option to make a 1oz bottle.

The Formula Pro® Advanced will not run if any of these symbols are illuminated on the LCD display.

Bottle LED:

Lights up when

bottle is placed

on drip tray WiFi LED:

Lights up when

connected to WiFi

(if blinking, see

troubleshooting)

Press the “start” button to dispense formula.

The Formula Pro® Advanced WiFi will dispense

powder & water together, then stop

automatically when dispensing is complete.

Check for clumps and shake or stir the bottle

if necessary. Check temperature and feed

your baby.

Ounce size indicates water volume only.

It does not include the volume of powder

added when mixing.

Using the Formula Pro®Advanced WiFi control panel

Press the “powder setting”button repeatedly

to select your setting 1 - 10.

Press the “temp” button to select temperature.

The temperature indicator will ash when

heating and will stay solid when the set

temperature is reached.

= Slightly warmer than body temperature

= Body temperature

= Room temperature

Press the “ounce” button repeatedly to select

the ounces of water you want to dispense.

Rell the powder when the arms of the

stirring wheel become visible. This is very

important for accurate formula measuring.

PLEASE NOTE: The level will appear higher

than the ounce size selected because of added

powder volume and/or variance in

bottle markings.

The formula pro will remember the setting

& ounce size even if it is unplugged or

turned o.

You do not need to select a powder setting

every time you make a bottle.

You can always change the ounce size or

powder setting by pressing the buttons again.

Example: 4 ounces of water plus powder volume

is approximately 4.5-4.75 ounces depending on

your formula powder type.

It is essential that you choose the correct

setting for your formula brand and type.

Use the app or go to babybrezza.com/FPA

to nd the correct setting for your formula.

Check the level

of mixed formula.

Some clumping may occur with hypoallergenic

formula and specialty formula powders that are

inherently dicult to mix with water.

IMPORTANT

109

11 2

Monthly Cleaning Instructions

Hand-wash all parts shown above with warm

soapy water, rinse well and dry thoroughly.

Hand wash water tank with warm soapy

water, rinse well and dry thoroughly.

Easy Daily Cleaning Instructions

Once a month, give your Formula Pro® Advanced WiFi a thorough cleaning.

Remove Funnel & Funnel Cover by pulling

out and down.

Wash Funnel & Funnel Cover with warm,

soapy water & rinse well.

Dry completely before re-installing.

Wipe the powder-dispensing hole on the

underside of the powder container using a

dry paper towel or soft dry cloth.

IMPORTANT

Monthly Descaling Instructions

Please watch set-up and cleaning videos at babybrezza.com/video.

You can leave the formula powder in the powder tank during the descaling process.

To prevent mineral scale on the water heater inside your Formula Pro® Advanced WiFi, follow these easy steps:

1. Remove the water tank, empty it and ll it with 20oz distilled vinegar & 20oz of puried water.

2. Place the water tank on the base of the machine & place a cup larger than 10oz under the funnel.

3. Select “10oz” with the“ounce” button, then press the “water only”button to dispense.

4. Empty the cup, place back under the funnel, then press the“water only” button again to dispense another 10oz.

5. Now unplug the machine, remove the water tank, and empty it. Let the machine sit for 4 hours.

6. Wash, rinse and ll the water tank to the max line with puried water, then place it back on the base.

7. Plug in the machine, place a cup to catch 10oz water and use the “water only” button to run an 10oz cycle.

Dispose of the water dispensed in the cup and then repeat this step to run the entire tank of puried water

through the machine. When the“Low Water” indicator turns on, you’re done rinsing.

8. Rell the water tank with puried water and return to normal use.

It is EXTREMELY IMPORTANT to clean the funnel after every 4 bottles made.

This will keep your Formula Pro® Advanced WiFi dispensing accurately.

Always make sure Funnel & Funnel cover are COMPLETELY DRY before re-assembling.

PLEASE NOTE: You don’t need to remove the powder container or the powder container parts for daily cleaning.

To make daily cleaning even easier, you can

purchase an extra funnel & funnel cover on

BabyBrezza.com Then you can swap the

spare funnel with the funnel that needs

to be cleaned. NOTE: you will still need to

wipe the powder dispensing hole as shown in Step 3

Suggestion to make cleaning easier

1211

If you can not remedy problems by using the troubleshooting chart above, do not return your Formula Pro® Advanced WiFi to the store.

Please contact Baby Brezza Customer Service at [email protected], 1-888-396-6552 or visit babybrezza.com for videos.

Possible Remedy

Temperature of dispensed

formula is too cold.

Water has not yet been heated to

correct temperature.

Wait for heater to warm water. Make sure selected

temperature symbol stays on solid instead of ashing.

Powder container lid is not completely closed. Turn Powder container lid clockwise to close completely.

See page 7, step 3 for details.

Water in Water Tank is too cold.

( Temp Symbol on LCD Flashing)

Wait for water to warm up.

Powder container is removed or not fully seated. Make sure powder container is placed on base properly.

Troubleshooting

Condition Possible Cause

Machine will not start. Make sure the plug is securely inserted into the power outlet.Machine is unplugged.

Insert funnel or push front of funnel until ush with machine.Funnel is removed or not fully inserted.

Add more water to water tank.Water level is below“MIN”line.

Water in Water Tank is too hot.

( Temp Symbol on LCD panel is ashing)

Wait for water to cool down.

Funnel cover is not straight on funnel and/or

not pushed down completely.

Align tab on front of Funnel Cover with notch in Funnel

and push down Funnel Cover completely.

Funnel will not t all the way

in Funnel Compartment.

Clean Funnel symbol is on, Formula Pro

beeps when start button is pressed.

Funnel and hole on underside of

Powder Container require cleaning.

Follow Steps on Page 7 to clean and dry Funnel and hole on

underside of Powder Container.

Not enough powder dispensed. Rell Powder Container with more powder.Powder level in powder container is too low.

Make sure silicone scraper is installed correctly.Silicone scraper is not installed correctly.

Incorrect powder setting selected. Go to: babybrezza.com/fpa to conrm setting for your

powder brand and type, then choose correct setting using

the “powder setting”button on the control panel.

Incorrect powder setting selected. Make sure to select the correct setting number for your

powder type. For details, go to: babybrezza.com/settings

Too much powder dispensed. Locking cover is not installed correctly. Check locking cover and make sure the front edge is locked

under the tab in the powder container.

See page 4, step 6 for details.

Not dispensing water. Water Tank not fully seated. Push Water Tank down all the way on Base.

Powder build-up on funnel cover &

underside of powder container.

Clean funnel, funnel cover and underside of

powder container every 4 bottles.

Frequent use without cleaning underside of

powder container. See page 7, step 3 for details.

No connection to Formula Pro® from

app.

Wi and/or Bluetooth on mobile device is o. Turn on WiFi and Bluetooth on mobile device to regain

connection.

Blinking Blue WiFi LED on Formula Pro®

control panel.

Connection error. Unplug Formula Pro® from power supply, wait 10 seconds,

then plug in Formula Pro and wait for WiFi LED on control

panel to light up without blinking.

Formula Pro® requires connection reset. With The Formula Pro plugged in, hold“temp” button for 10

seconds to reset Wi. Restart the app on your mobile device

and follow steps in-app to reconnect your Formula Pro® to WiFi.

Machine has not been cleaned well. Disassemble, clean by hand-washing, completely dry all parts

and reassemble.

Long Term Storage Instructions

Error Codes

It is EXTREMELY IMPORTANT to clean the machine and remove all formula powder residue before storage.

If you’re going to store your Formula Pro® Advanced for later use, or will not use it for a while, please follow the

instructions below:

1. Remove the powder container parts, funnel, funnel cover, drip tray and water tank from the base.

2. Wipe the base with a clean damp cloth and make sure to remove any and all formula residue. Dry the base well.

3. Empty the powder container, wash all powder container parts, dry throughly, reassemble, & reinstall on the base.

4. Follow the Monthly Descaling Instructions on page 12, steps 1-7 only. Do not remove or rell the water tank after

step 7.

5. Now place a cup to catch 10oz water under the funnel, then press & hold the “water only” button for 5 seconds.

Water will dispense continuously until the machine is completely empty, then stop automatically.

6. Unplug the machine, remove the funnel, funnel cover and water tank, dry them both throughly and reinstall

them on the machine.

7. Your machine is now ready for storage. Pack the machine in its box, or enclose it in a bag to keep it dust free.

In the unlikely event of electrical component error or interruption during operation, the following codes will

be displayed on the LCD screen. Pressing and holding the stop button will clear the code and operation should

return to normal. If the code returns or is unable to be cleared, please contact Baby Brezza Customer Service.

Indicates an operation error of the motor that turns the powder container parts.