Babcockdavis BDT Manual de instrucciones

, Inc.

Rev 7/2020

Installation, Operation

+ Maintenance Manual

Draft Stop Access Door

Model(s): BDT/BDW/BDP

GENERAL DESCRIPTION

Access Doors are designed and built for years of convenient and

easy access to mechanical areas in commercial buildings.

Transportation + Storage

1. Inspect all shipments and materials for missing or damaged components and hardware.

2. Material must be stored in a clean, dry location.

INSTALLATION

Please read the instructions before beginning work.

When correctly installed, the door will close and latch when released from an open position.

Preparation

Wall framing is required:

oHinge and Latch Side: Doors 24” x 24” and smaller

oAll Four Sizes: Doors larger than 24” x 24”

oWall opening is door size plus 1/4”. Example: 12“ x 12” door, opening should be 12-1/4” x 12-1/4”.

GENERAL SAFETY PRECAUTIONS Improper selection, installation, or use can cause personal injury or property damage. It

is solely the responsibility of the user, through its own analysis to select products suitable for their specific application

requirements, ensure they are properly maintained, and limit their use to its intended purpose. Follow proper local,

state and federal regulations for proper installation and operation requirements.

, Inc.

REV 7/2020

Draft Stop Access Door

Installation, Operation & Maintenance Model(s): BDT/BDW/BDP

STUD WALL

Tools Needed

5/32 Drill Bit and Driver

Screwdriver

Supplies Needed

#12 Drywall Screws

Installation

1. Place door in opening and mark location of attachments on studs using holes in latch and hinge side of

door frame as guides.

2. Remove door and drill 5/32” holes through studs at points marked for attachment.

3. Place door into position and fasten to wall as follows:

4. For panels utilizing a drywall bead flange (DW), screws should be fastened at 18” on center (O.C.)

maximum through the flange face in addition to the pre-existing holes located on the inside of the

frame.

5. Check door for freedom of movement. If it binds, shim to remove any racking of frame at attachment

points.

6. Install the spring. Self-closure of door is required for all draft stop applications; thus, spring must be

installed.

MASONARY WALL

Tools Needed

Drill Bit and Drill

Supplies Needed

#10-32 x 1” flat-head steel machine screws

Installation

1. For new construction, unfold masonry anchors prior to fill.

2. Place door in opening and mark location of attachments using holes in latch and hinge sides of door

frame as guides.

3. Remove door and install expansion shields in wall at points marked.

4. Place door into position and fasten with #10-32 x 1” flat-head steel machine screws.

Wood Substrate

#12 X 1-1/4” drywall screws; minimum of 2 per side

Steel Substrate

#12 X 1-1/8” drywall screws; minimum of 2 per side

, Inc.

REV 7/2020

Draft Stop Access Door

Installation, Operation & Maintenance Model(s): BDT/BDW/BDP

5. Check door for freedom of movement. If it binds, shim to remove any racking of frame at attachment

points.

7. Install the spring. Self-closure of door is required for all draft stop applications; thus, spring must be

installed.

, Inc.

REV 7/2020

Draft Stop Access Door

Installation, Operation & Maintenance Model(s): BDT/BDW/BDP

OPERATION

Access doors are designed and built for years of dependable wall and ceiling access.

Our access doors come standard with paintable powder coat finish

MAINTENANCE

oAccess doors should be manually operated once a year to check performance.

oLubricate moving parts such as hinges and latches with a silicone spray lube as required to

maintain a smooth opening and closing of the door. Do not over grease. Do not use regular

lubricating oil as it can attract dust and grit.

oNon-moving parts can be cleaned with a mild soap or dishwashing detergent and water

solution.

QUESTIONS?

For more information on installation, repair or replacement, please visit

www.Babcockdavis.com or call 800.547.2635.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de seguridad de babcockdavis

babcockdavis

babcockdavis Safe-T-Lume BEM-DS1 Manual de usuario

babcockdavis

babcockdavis Lume-A-Lite BEM-DSH1-10 Manual de usuario

babcockdavis

babcockdavis Personnel Series Manual de usuario

babcockdavis

babcockdavis BDC-1002 Manual de usuario

babcockdavis

babcockdavis BFDF Manual de usuario

babcockdavis

babcockdavis BCGVS-EW-P Manual de instrucciones

babcockdavis

babcockdavis Personnel II Roof Hatch Manual de usuario

babcockdavis

babcockdavis BSRA Manual de instrucciones

babcockdavis

babcockdavis BSTSB Manual de usuario

babcockdavis

babcockdavis BSRCAY Manual de usuario

babcockdavis

babcockdavis BNT Manual de usuario

babcockdavis

babcockdavis 31722 Manual de instrucciones

babcockdavis

babcockdavis Lume-A-Lite BEM-SLE100 Manual de instrucciones

babcockdavis

babcockdavis Lume-A-Lite BEM-DTO1-100 Manual de instrucciones

babcockdavis

babcockdavis Lume-A-Lit BEM-SNE Manual de usuario

Manuales populares de Equipo de seguridad de otras marcas

Innova

Innova Xtirpa Manual de instrucciones

bolle SAFETY

bolle SAFETY B810 Manual de usuario

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manual de usuario

Hiltron security

Hiltron security POWER8E Guía

Hatco

Hatco B-950P Manual de usuario

Sitec

Sitec TX MATIC Manual de usuario

TEUFELBERGER

TEUFELBERGER GRIP 12 Manual de usuario

MSA

MSA PremAire System Manual de usuario

AMC

AMC 1022M Series Manual de usuario

Trinity

Trinity CASS S3 Manual de usuario

CMC

CMC Helitack HotSeat Manual de usuario

Force

Force P-35 Manual de usuario

ACM

ACM SAFETY D200 Manual del producto

Honeywell

Honeywell Miller H-Design DuraFlex Manual del operador

ROCK

ROCK P-451 AS Manual de usuario

Power first

Power first 2XYR7A Manual de servicio

SCHUBERTH

SCHUBERTH SHP 28-C Manual de usuario

Trango

Trango CINCH Manual de usuario

babcockdavis BDT Manual de instrucciones

Manuales populares de Equipo de seguridad de otras marcas