B-K lighting EC Guía de configuración
PRELIMINARY
7-11-12
REFERENCE NUMBER
INS000942
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
EC™/ ED™/ AS™/ SM-AR™
Architectural Surface Installation Instructions
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
SM-AR
TOOLS
NEEDED:
By Others
5/32” Allen wrench
Phillips Screwdriver
Wire connectors
(recommended silicone filled wire connectors)
ED AS
This set of instructions works for:
EC - El Capitan™
ED - El Dorado™
AS - Accent Star™
SM-AR - Arti-Star Surface Downlight™
EC
4 inch octagonal junction box
(By Others)
Universal Ring
18 Gauge Wire
TECHNOLOGY
with
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
• Suitable for wet locations
Hot Surface
Warning High Voltage
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
B-K LIGHTING
PROJECT:
TYPE:
3. Mount fixture using two (2) #10-24 hex screw
to installed back box. Do not over tighten.
Phase 2 - Finish Installation of Fixture with Transformer in Junction Box.
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
1. Ground primary branch circuit to junction box
per NEC. Remove #10-24 Stainless Steel Phillips
screws from mounted back box. Install universal
mounting ring (supplied with faceplate) using
#10-24 screws onto back box. Align faceplate
mounting holes to final mounting position.
2. Make two connections from 12V transformer
to LED source leads (18 gauge wire) and two
connections to primary branch cuircuit using
proper wire connectors (By Others).
Phase 1 - Rough In
Installation of Back box
1. Install Conduit (by others) to be used with
this product.
2. Install junction box so that front face is flush
with finished wall or ceiling.
3. Connect box to conduit and pull wires for
connections (See Wiring diagram).
Additional Info
• Please follow National and Local electrical codes for your area.
• 4” round cast box is provided with Five (5) 1/2” threaded hubs
for conduit entry (4 on sides and one on back of box).
• Suitable for through wire
• Suitable for installation into combustible materials.
• Rated for 90° C.
Please refer to the low voltage design guide at www.bklighting.com/
lvguide before installation for proper wire selection.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
3167387
ETL LISTED
CONFORMS TO ANSI/UL STANDARD 1838,
CERTIFIED TO CSA STD C22.2 NO.250.7
CSA STD C22.2 TIL B-58A
EC™/ ED™/ AS™/ SM-AR™
Architectural Surface Installation Instructions
PRELIMINARY
7-11-12
REFERENCE NUMBER
INS000942
3. Mount fixture using two (2) #10-24 hex screw
to installed back box. Do not over tighten.
Phase 2 - Finish Installation of Fixture with Remote Transformer.
1. Remove #10-24 Stainless Steel Phillips screws
from mounted back box. Install universal
mounting ring (supplied with faceplate) using
#10-24 screws onto back box. Align faceplate
mounting holes to final mounting position.
2. Make two connections from remote 12V
transformer to LED source leads (18 gauge
wire) using proper wire connectors (By
Others).
TECHNOLOGY
with
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
B-K LIGHTING
PROJECT:
TYPE:
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
3167387
ETL LISTED
CONFORMS TO ANSI/UL STANDARD 1838,
CERTIFIED TO CSA STD C22.2 NO.250.7
CSA STD C22.2 TIL B-58A
EC™/ ED™/ AS™/ SM-AR™
Architectural Surface Installation Instructions
PRELIMINARY
5-17-12
REFERENCE NUMBER
INS000942
TECHNOLOGY
with
To Change Lumen Output (when required).
1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.
3. Place cap on fixture and tighten set screw.
Tighten screw to 1/2 inch pounds. Top of
screw should sit flush with fixture cap.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and
will void warranty.
2. With flat head screw driver rotate dial to
desired lumen output.
This product is available with Adjust-e-Lume® (Patent Pend.) for DynamicLLumen Output Control
Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set
to the appropriate light level desired during installation.
RELEASED
7-13-12
REFERENCE NUMBER
INS000001
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
TECHNOLOGY
with
5/64” allen wrench
Small Flat Head Screw Driver
Warning High Voltage Hot Surface
NEEDED
FOR
INSTALLATION:
By Others
LED BOARD/DRIVER/OPTICS
2 1/4” Body Size
Standard Installation/Replacement
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
Re-placing LED Board/Driver and Optics
1. Use 5/64” Allen wrench to loosen #8-32 stainless
set screw and remove cap.
2. Space three fingers evenly around the optic and
gently rock optic to remove.
4. Disengage LED board and driver assembly. Replace
with new board and driver assembly.
5. Reverse install LED board and driver by carefully
engaging quick disconnects and inserting into
fixture body. Secure LED board in place with
stainless steel screws. Snap optics in place.
6. With flat head screw driver rotate dial to desired
lumen output.
3. Use 5/64” Allen wrench to remove two (2) #2-56
socket head cap screws on LED board, grasp
LED board and gently pull up to expose quick
disconnect.
To Change Lumen Output (when required).
This product is available with Adjust-e-Lume® (Patent Pend.) for DynamicLLumen Output Control
Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set to the
appropriate light level desired during installation.
RELEASED
7-13-12
REFERENCE NUMBER
INS000001
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
TECHNOLOGY
with LED BOARD/DRIVER/OPTICS
2 1/4” Body Size
Standard Installation/Replacement
7. Place cap on fixture and tighten set screw. Tighten
screw to 1/2 inch pounds. Top of screw should sit
flush with fixture cap.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and
will void warranty.
8. If your fixture requires aiming, use 5/32” Allen
wrench to slightly loosen #10-32 stainless steel
black oxide socket head cap screw at the knuckle
for aiming purposes. Tighten to secure desired
location.
To Change Lumen Output (when required).
1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.
3. Place cap on fixture and tighten set screw.
Tighten screw to 1/2 inch pounds. Top of
screw should sit flush with fixture cap.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and
will void warranty.
2. With flat head screw driver rotate dial to
desired lumen output.
This product is available with Adjust-e-Lume® (Patent Pend.) for DynamicLLumen Output Control
Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set
to the appropriate light level desired during installation.
Este manual sirve para los siguientes modelos
7
Otros manuales de Luz exterior de B-K lighting
B-K lighting
B-K lighting SARATOGA Series Manual de usuario
B-K lighting
B-K lighting Brick Star Manual de usuario
B-K lighting
B-K lighting GARDEN STAR GR-K Manual de usuario
B-K lighting
B-K lighting ALPINE Series Manual de usuario
B-K lighting
B-K lighting HP2 SERIES Manual de usuario
B-K lighting
B-K lighting CO2 Manual de usuario
B-K lighting
B-K lighting MB2 Manual de usuario
B-K lighting
B-K lighting Well Star WS Series Manual de usuario
B-K lighting
B-K lighting BKSSL MINI-MICRO iLUME Manual de usuario
B-K lighting
B-K lighting Precision2 HP2 Series Manual de usuario
B-K lighting
B-K lighting CK Manual de usuario
B-K lighting
B-K lighting PM4RM ROUND CAMLOCK Guía de configuración
B-K lighting
B-K lighting CATSKILL Series Manual de usuario
B-K lighting
B-K lighting HP2 SERIES Manual de usuario
B-K lighting
B-K lighting DENALI Manual de usuario
B-K lighting
B-K lighting Litestick Manual de usuario
B-K lighting
B-K lighting DENALI ST-DE-TR-A Manual de usuario
B-K lighting
B-K lighting HP2 SERIES Manual de usuario
B-K lighting
B-K lighting ARTISTAR UPLIGHT Manual de usuario
B-K lighting
B-K lighting TENAYA2 Series Manual de usuario
Manuales populares de Luz exterior de otras marcas
Lindby
Lindby 9949029 Manual de usuario
HEPER
HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento
HEPER
HEPER LW8034.003-US Instrucciones de instalación y funcionamiento
Maretti
Maretti VIBE S 14.6080.04.A Manual de usuario
BEGA
BEGA 84 253 Manual
HEPER
HEPER MINIMO Instrucciones de instalación y funcionamiento
LIGMAN
LIGMAN BAMBOO 3 Manual de usuario
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Manual de usuario
urban ambiance
urban ambiance UQL1273 Manual de usuario
TotalPond
TotalPond 52238 Manual de usuario
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Manual de usuario