B-K lighting DENALI Manual de usuario

Hot SurfaceHigh VoltageWarning

Standard Installation

DENALI

SURFACE MOUNT - INTEGRAL

Flammable

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local and

Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective

equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and

lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause an

unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part, as

this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body.

• Replace LED assembly only with correct wattage and type of

power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause an

unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before

replacing lamp/LED. Fixture gets HOT quickly!

Contact only switch/plug when turning on.

Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time.

Use a soft cloth or gloves. Oil from skin may cause

damage.

SAVE THESE INSTRUCTIONS

· Suitable for wet locations

IMPORTANT LISTINGS AND CERTIFICATIONS

5/32” Allen Wrench

Phillips Screwdriver

Waterproof Wire Connectors

TOOLS

NEEDED:

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

INSTRUCTIONS

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL

ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

RELEASE DATE

06/26/2023

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS-2824-00

SM-DE

Universal

Mounting Ring

Phase 2 - Finish Installation of Fixture with Remote Driver

RELEASE DATE

10/25/2022

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS-2815-00

RELEASE DATE

06/26/2023

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS-2824-00

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Standard Installation

DENALI

SURFACE MOUNT - INTEGRAL

4. Mount fixture using two (2) #10-24 hex screws to

installed back box. Seal building envelope as per

NEC. Do not overtighten.

1. Install universal mounting ring (included with

fixture) using #10-24 screws onto back box. Align

fixture mounting holes to final mounting position.

2. Pull primary branch circuit wiring out of back box.

Leave sufficient wiring for any future service and

maintenance.

WIRING DIAGRAM

3. Make watertight connections from branch circuit

wiring to fixure leads using waterproof wire

connectors (not included) in splice location as

per NEC. Connect incoming green ground wire to

ground wire from fixture. See wiring diagram.

All line voltage connections must be made in

compliance with the National Electrical Code.

Failure to do o will void warranty.

HOT (BLACK)

GROUND (GREEN) GROUND FIXTURE

NEUTRAL

HOT

NEUTRAL (WHITE)

WIRING DIAGRAM - Dimming

HOT (BLACK)

GROUND (GREEN) GROUND

FIXTURE

NEUTRAL

HOT

NEUTRAL (WHITE)

DIM + DIM +

DIM -

Phase 1 - Rough In

Installation of Back box

1. Install conduit (not included) to be used

with this product.

2. Install junction box so that front face is

flush with finished wall or ceiling. Seal

building envelope as per NEC.

3. Connect box to conduit and pull wires for

connections (See wiring diagram).

Additional Info

• Please follow National and Local electrical codes for your area.

• Use 4” round cast box (not included).

• Suitable for through wire.

• Suitable for installation into combustible materials.

• Rated for 90° C.

• Junction box, universal mounting ring screws, box mounting

hardware and gaskets (not included).

RELEASE DATE

10/25/2022

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS-2815-00

RELEASE DATE

06/26/2023

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

REFERENCE NUMBER

INS-2824-00

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

3. Remove retainer.2. Twist and pull away optic.1. Loosen three (3) #8-32 set screws with a 5/64”

allen wrench on cap, then remove cap.

8. Connect new driver assembly to fixture leads. Place

connections inside body cavity, then slide down

fixture body along guides.

4. Disconnect driver assembly from fixture body.

5. Separate heatsink from driver assembly via quick

disconnect.

11. Install cap by tightening three (3) #8-32 set screws

with a 5/64” allen wrench. Do not over tighten.

Cap should be able to rotate without force.

10. Twist to reinstall optic onto optic holder.

6. Remove protective plastic from the double-sided

tape square on clean top of driver assembly.

7. Reconnect heatsink assembly to driver assembly

via quick disconnect. Quick disconnect tucks into

space underneath heatsink. Press heatsink down

along guides until flush and even with tape on

driver.

9. Reinstall retainer.

LINE UP WITH THE HOLE

Integral Driver Replacement

Standard Installation

DENALI

SURFACE MOUNT - INTEGRAL

Otros manuales de Equipo de iluminación de B-K lighting

B-K lighting

B-K lighting Denali Series Manual de usuario

B-K lighting

B-K lighting LT Manual de usuario

B-K lighting

B-K lighting SS Manual de usuario

B-K lighting

B-K lighting BACK BOX Manual de usuario

B-K lighting

B-K lighting Precision2 HP2 Series Manual de usuario

B-K lighting

B-K lighting ArtiStar Remote ES16 Metal Halide Manual de usuario

B-K lighting

B-K lighting Precision2 HP2 Series Manual de usuario

B-K lighting

B-K lighting PRECISION2 CO2 Series Manual de usuario

B-K lighting

B-K lighting ArtiStar Integral Manual de usuario

B-K lighting

B-K lighting Path Star Manual de usuario

B-K lighting

B-K lighting PS Manual de usuario

B-K lighting

B-K lighting MICRO NITE STAR Manual de usuario

B-K lighting

B-K lighting YOSEMITE Series Manual de usuario

B-K lighting

B-K lighting ORION Manual de usuario

B-K lighting

B-K lighting ArtiStar Series Manual de usuario

B-K lighting

B-K lighting ORION Manual de usuario

B-K lighting

B-K lighting SQUARE ADJUSTABLE WELL STAR Manual de usuario

B-K lighting

B-K lighting MB2 Manual de usuario

B-K lighting

B-K lighting Union Bollard Manual de usuario

B-K lighting

B-K lighting HP2RM Manual de usuario

B-K lighting

B-K lighting Mini-Micro Series Manual de usuario

B-K lighting

B-K lighting SIGN STAR Series Manual de usuario

B-K lighting

B-K lighting Altair Manual de usuario

B-K lighting

B-K lighting MINI-MICRO DRIVESTAR Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario